in tension or compression. [A,=1.2kN, A,=0.88KN, C,=1.8kN, C,=3.13KN, FBc= 2.37(T), FCD= 5.21(C), d) Draw FBD of pin at A. Determine unknown member force. 3 kN 1.5 m 10 = 30° %3D A QAK 2 m -2 m 4 kN Fig. Q5 [A=1.2kN, A,=0.88KN, C,=1.8kN, C-3.13KN, FBc= 2.37(T), Fen= 5.21(C), FAB=2.37(T), FBD= 4.0(T), FAD= 1.47(C)] ВС %3D CD %3D %3D %3D АВ

in tension or compression. [A,=1.2kN, A,=0.88KN, C,=1.8kN, C,=3.13KN, FBc= 2.37(T), FCD= 5.21(C), d) Draw FBD of pin at A. Determine unknown member force. 3 kN 1.5 m 10 = 30° %3D A QAK 2 m -2 m 4 kN Fig. Q5 [A=1.2kN, A,=0.88KN, C,=1.8kN, C-3.13KN, FBc= 2.37(T), Fen= 5.21(C), FAB=2.37(T), FBD= 4.0(T), FAD= 1.47(C)] ВС %3D CD %3D %3D %3D АВ

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(1) E 4 kips C Lon -9 ft-9 ft——9 ft——94—- 1 kips What are the member forces in BD, BE and CE? Indicate if they are in tension (T) or compression (C).
The frame is used to carry high-voltage wires. If b=600mm, α=30° and W=981 N, find the internal force in member HJ? (Draw free body diagram)
Hi! Hope you can help me with this. F1 = 500kN F2 = 600kN Find the force member in CD, BD, AB, BC. Indicate if Tension or Compression
What is the shear stress, fv, for the glue of the lap of the connection with P= 15,000 lb? What is the axial stress due to tension, ft, on the thinner of the two plates?
PROBLEM: Determine the forces in each member using any methoddiscussed in your theory of structures/mechanics. Using Software is notallowed. Show complete solution and tabulate your answers indicatingwhether it is compression or tension. Use Pn = 205 kN, Po = Zero. a) From the Problem and the image , Design one tension member, use either a double angle of a wt section. Check its adequacy using 1 line of bolts (three bolts in a line spaced at 75mm on centers) Assume a bolt diameter from 16-22mm. Use A 36 for all steel. Neglect block shear.
Given a 2meter Wide Flange steel compression member with A=4,513mm2, Ix=86,630,006mm4 and Iy=3,824,544mm4 with Fy = 345MPa. Calculate the critical buckling stress in MPa if both ends are fixed or rigid. Express your answer in 2 decimal places.
Static Problem. Indications:The system shown is composed of an ABG bar, supported by a pin at point A and by a collarsmooth at point B (the collar slides on the bar ABG). The collar is pinned to the BDE bar, and theRod BDE is supported by a pin at D and a cable at end E.Based on the above, determine:a) The load P, such that the cable force EF is T.b) The internal loads in a section passing through point G (normal and shear force, and momentflexing).c) Draw bar BDE horizontally and generate the shear force and moment diagramsflexing Indicate the maximum values of shear force and bending moment and their location.?= 22 lb ? = 7 in ? = 6 in
The cover of a cylindrical pressure vessel made of cast iron is shown in fig.1 The inner diameter of the cylinder is 500 mm and the internal pressure is limited to 2MPa. The cover is fixed to the cylinder by means of 16 bolts with a nominal diameter of 20 mm. Each bolt is initially tightened with a preload of 20 KN. The bolts are made of steel FeE250 (S yt = 250 N/ mm 2 ). Assume. E for steel = 207 KN/mm 2 ,E for cast iron = 100 KN/mm 2, E for Zinc = 90 KN/mm 2,Determine the factor of safety for bolts considering the effect of the gasket.
A central horizontal section of a hook is a symmetrical trapezium of inner width=67.5mm and of outer width =22.5mm. The depth of the section is 90mm. The hookcarries a load of 37.5kN. The load line passes through the centre of curvature. Theradius of the hook is 52.5mm. Determine the maximum compressive and tensilestresses in the section of the hook.
Why is is that when I compute for the diameter, the answer is 7.9706? How was 13.22 obtained? Bartleby link for solution: https://www.bartleby.com/questions-and-answers/a-steel-rod-is-stretched-between-two-rigid-walls-and-carries-a-tensile-load-of-5000-n-at-20c.-if-the/5c99ed3b-d083-41be-a905-b15aa3bc8648
Design the spigot (in tension and compression) of the spigot and socket cotterjoint which is subjected to alternate tensile and compressive loading of 50 kN usingthe following data:Yield strength of cotter material SYS = 400 N/mm2, Factor of safety = 4 (for spigot)Assume thickness of cotter, t = 0.30d, where d is the diameter of the rod.
Rigid bar ABC is supported by pin-connected bar (1). Bar (1) is 2.0-in. wide, 1.00-in. thick, and made of aluminum that has anelastic modulus of E = 12,000 ksi. Determine the maximum magnitude of load P that can be applied to the rigid bar withoutcausing member (1) to buckle