mild steel shaft of 50 mm diameter is subjected to a bending moment of 2000 N-m and a torque T. If the yield point of the steel in tension is 200 MPa, find the maximum value of this torque without causing yielding of the shaft according to: The maximum distortion strain energy theory of yielding

mild steel shaft of 50 mm diameter is subjected to a bending moment of 2000 N-m and a torque T. If the yield point of the steel in tension is 200 MPa, find the maximum value of this torque without causing yielding of the shaft according to: The maximum distortion strain energy theory of yielding

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.5.1P: A circular copper bar with diameter d = 3 in. is subjected to torques T = 30 kip-in. at its ends....

See similar textbooks

Related questions

Q: Q1-A 75-Kg man wants to pull a 145- Kg box and the coefficient of static friction between the box…

Q: 6.8 Review Questions 1. Balanced spectral composition of artificial white light is critical for…

A: Please find the solution below

Q: A certain fighter aircraft is set to travel at a speed of 3200km/h. The ambient temperature is…

Q: 3. Electrode This is usually made of graphite, brass, copper and copper tungsten alloys and is…

A: Electrical discharge machining is also known as spark machining is a metal fabrication process in…

Q: The 15 lb suitcase is released from rest at C. After it slides down the smooth ramp, it strikes the…

Q: The simple truss shown supports the two loads, each of magnitude L. Deter- mine the forces in…

A: When a push or the pull applied on the body having mass 'm', it has the tendeycy to change it's…

Q: Air enters the compressor of 5 m3/s. The compressor back work ratio. of an ideal air-standard…

Q: Air enters the compressor of an ideal air-standard Brayton cycle at 100 kPa, 27 °C, with a…

Q: Determine the position of the centroid for the figures shown below.

Q: Can you discuss the process of lock bumping? In fact, there’s an electric device that uses…

A: Around 2002, the method known as "lock bumping" was first identified as a security risk. A…

Q: Refrigerant 22 is the working fluid in a Carnot vapor refrigeration cycle for which the evaporator…

A: R22 refrigerant is used in central air conditioners, heat pumps, vehicle AC systems etc. Chemical…

Q: Find the sum and angle of two displacement vectors A and B Laying in the XY- Plane and given by A =…

A: Given data The given vectors are :A→ = 2 i^ + 2j^B→ = 2i^ - 4j^ We have to find the sum and angle of…

Q: Vector A has a magnitude of 6 units and it is in the direction of positive X-axis vector B has a…

Q: Determine the direction of force F in the direction of the vector AB when A = (2,3,6) and B =…

Q: The 46-kg homogeneous smooth sphere rests on the 32° incline A and bears against the smooth vertical…

A: When an amount of push or the pull applied on the object, it has the ability to change its state…

Q: (Q1 A hollow shaft has to transmit 6 MW at 150 rev/min. The maximum allowabl て 180 L=1 stress is not…

Q: The figure below shows a snapshot of the travelling wave in space at some arbitrary time to > 0.…

A: Write the expression of angular frequency. ω=vkω=ck ...... (1)

Q: AB -1.5m 9 'G 15m FAC Part C If the maximum tension allowed in each cable is 3.8 kN determine the…

Q: A simply supported wood beam is reinforced with a steel plate of width b as shown in the figure. The…

Q: A Pelton wheel has a diameter of 2 m and develops 500 kW when rotating 180 rpm. What is the average…

A: Givenpelton wheel turbined=2mP=500kWN=180rpmoperating at maximum efficiency

Q: Let's consider a rod subjected to the shown axial forces. If we consider a linear elastic behavior,…

Q: Draw the shear-force and bending-moment diagrams for the beam shown. Determine the bending moment…

Q: 6. A propeller shaft in a ship is 350 mm in diameter. The allowable working stress in shear is 50…

Q: 1. Water with a density of ρ=1000 kg/m3 flows through a pump with a flow rate of 0.40 m3 /s. The…

Q: If an isotropic material has a Young's modulus of 200 Gpa and a Poisson's ratio of 0.3, calculate…

Q: Water enters the heater at 30°C and leaves at 150°F, what is the temperature difference in °C? A.…

A: Given : inlet temperature , T1 = 30 0C outlet temperature , T2 = 150 0F To find :…

Q: 3. An octahedron of sides 50 mm lying on the HP on a face such that one side of the face which is on…

Q: If a pump requires a minimum of 2.75 m of NPSHA, how high can the centerline of the pump be located…

Q: A car jack uses a single square-thread screw to raise a known load. The major diameter and pitch of…

Q: ANCIENT INVENTION Mechanical Clock 725 A.D. Do and Answer the following Question: 1. Make a…

A: Given questions: 1. Make a description of Mechanical clock2. What is the invention?3. What are the…

Q: Consider a cold air-standard Diesel cycle. Operating data at principal states in the cycle are given…

Q: (A) In a food processing plant a brine solution is heated from 6°C to 12˚C in a double pipe heat…

Q: Consider a cold air-standard Diesel cycle. Operating data at principal states in the cycle are given…

A: Draw the P-V diagram of the a cold air-standard Diesel cycle.

Q: Consider a cold air-standard Diesel cycle. Operating data at principal states in the cycle are given…

A: GIVEN DATA- p1 = 100 kPa, T1 = 340 K, and T3 = 4850.3 K, r = 15 and rc = 2. For n = 1.3, cv = 0.718…

Q: Refrigerant 22 is the working fluid in a Carnot vapor refrigeration cycle for which the evaporator…

Q: Assume that a skater of mass m, moving at a constant speed Vo, suddenly stands stiffly with skates…

Q: Compute for the vertical reaction at the hinged support at C. Given the following data and figure:…

A: P1=9 NP2=17 NF1=12 Nx=2 mz=5 my=7 m

Q: Air enters the compressor of an ideal air-standard Brayton cycle at 100 kPa, 27 °C, with a…

A: Given: Let us consider the given, P1=100 kPaT1=27°C= 300 kV1=5 m3sr=5T3=1127°C =1400 K To find: The…

Q: Refrigerant 22 is the working fluid in a Carnot refrigeration cycle operating at steady state. The…

A: Given data Refrigerant : R22 Cycle : Carnot refrigeration cycle Condenser temperature : 36°C…

Q: Give the formula for ∆U, ∆H, Q , W, ∆S for the following thermodynamic processes: 1. isothermal 2.…

Q: Continuous level measurement in a tank filled with grain can be done using a _________ sensor.

Q: Calculate the internal energy for each of the four stages given in Problem no. 3.

A: Given data We have to calculate the internal energy for each of the given points: a. T=212.4°C and…

Q: is exposed to cooler air at 30 °C with h = 60 W²/m °C. Calculate the heat loss from the tube to the…

A: d1=5cm=0.05mr1=0.025md2=7.6cm=0.076mr2=0.025mRadius,r3=r2+Insulation…

Q: 17-102. The 25-lb slender rod has a length of 6 ft. Using a collar of negligible mass, its end A is…

Q: Nanometer is equal to ------------- meter.

A: To find : 1 Nanometer into meter

Q: Vector A has a magnitude of 6 units and it is in the direction of positive X-axis vector B has a…

Q: At C two cables are tied and loaded as shown in Fig. figure. Knowing that Q = 60 lb, determine the…

Q: Use the method of sections to compute for the force in members BD, CD, and CE of the cantilever…

Q: Describe the changes to the pressure, temperature and velocity of the air as it passes through a…

Q: Air enters the compressor of an ideal air-standard Brayton cycle at 100 kPa, 27 °C, with a…

Concept explainers

Strain energy

The term strain indicates the variation in an object's length, area, and volume when the object is subjected to an external force. The external force may be of normal, shear, moment, torque, etc. The strain in an object depends on the types of external force and cross-section of the object. Mathematically, the evaluation of strain can be obtained with the help of elastic constants.

Question

100%

A mild steel shaft of 50 mm diameter is subjected to a bending moment of 2000 N-m and a torque T. If the yield point of the steel in tension is 200 MPa, find the maximum value of this torque without causing yielding of the shaft according to:

The maximum distortion strain energy theory of yielding

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
-7 A steel tube (G = 11.5 x 106 psi) has an outer diameter d2= 2.0 in. and an inner diameter dt=1,5 in. When twisted by a torque 7", the tube develops a maximum normal strain of 170 x 10-6. What is the magnitude of the applied torque T?
A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
A solid circular bar A BCD with fixed supports at ends A and D is acted upon by two equal and oppositely directed torques T0, as shown in the figure. The torques arc applied at points B and C each of which is located at distance x from one end of the bar. (The distance x may vary from zero to L/2.) For what distance x will the angle of twist at points B and C be a maximum? What is the corresponding angle of twist 0max?
Solve the preceding problem for the following data: diameter LO m, thickness 48 mm, pressure 22 MPa, modulus 210 GPa. and Poisson's ratio 0.29
A hollow steel shaft used in a construction auger has an outer diameter d2= 6.0 in. and inner diameter d1= 4.5 in. (see figure). The steel has a shear modulus of elasticity G = 11.0 × 106 psi. For an applied torque of 150 kip-in., determine the following quantities: shear stress at the outer surface of the shaft, shear stress at the inner surface, and rate of twist (degrees per unit of length). Also, draw a diagram showing how the shear stresses vary in magnitude along a radial line in the cross section.
A circular steel tube of length L = 1.0 m is loaded in torsion by torques T (see figure). (a) If the inner radius of the tube is r1= 45 mm and the measured angle of twist between the ends is 0.5°, what is the shear strain y1(in radians) at the inner surface? (b) If the maximum allowable shear strain is 0.0004 rad and the angle of twist is to be kept at 0.45° by adjusting the torque T, what is the maxi mum permissible outer radius (r2)max?
Solve the preceding problem if the cube is granite (E = 80 GPa, v = 0.25) with dimensions E = 89 mm and compressive strains E = 690 X l0-6 and = = 255 X 10-6. For part (c) of Problem 7.6-5. find the maximum value of cr when the change in volume must be limited to 0.11%. For part. find the required value of when the strain energy must be 33 J.
Two sections of steel drill pipe, joined by bolted flange plates at B, arc subjected to a concentrated torque 4000 kip-in. at x = 3 ft, and a uniformly distributed torque t0= 50 kip-ft/ft is applied on pipe BC. Let G = 11,800 ksi and assume that pipes AB and BC have the same inner diameter, d = 12 in. Pipe AB has a thickness tAB= 3/4 in., and pipe BC has a thickness tBC= 5/8 in. Find the reactive torques at A and C and the maximum shear stresses in each segment.
A thin-walled hollow tube AB of conical shape has constant thickness I and average diameters dAand dBat the ends (see figure). Determine the strain energy U oT the tube when it is subjected to pure torsion by torques T, Determine the angle of twist of the tube. Note: Use the approximate formula / ird^tlA for a thin circular ring; see Case 22 of Appendix E.