O 15 KN/m 1. The beam shown in the figure carries distributed loads. Design the square (a x a) cross-section of the timber columns of the beam. Column A has the same dimensions as Column B. The strength of the column is 80 MPa. Express the dimensions of the column in whole number. 1.50 m 3 m 1 m 10 KN/m 1 m 10 KN/m A B

O 15 KN/m 1. The beam shown in the figure carries distributed loads. Design the square (a x a) cross-section of the timber columns of the beam. Column A has the same dimensions as Column B. The strength of the column is 80 MPa. Express the dimensions of the column in whole number. 1.50 m 3 m 1 m 10 KN/m 1 m 10 KN/m A B

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.16P: Figure (a) shows the cross-sectional dimensions for the structural steel section known as C1020...

See similar textbooks

Similar questions

An aluminum rod is hanging from one end. The rod is 1 m long and has a square cross section 20 mm by 20 mm. Find the extension of the rod resulting from its own weight. Take E = 70 GPa and the unit weight = 27 kN/m3.
The horizontal beam is assumed to be rigid while supporting the distributed load. Determine the angle of inclination of the beam after the load is applied. Each support consists of a wooden post with a diameter of 120 mm and an original length (unloaded) of 1.40 m- Consider E = 12 GPa
As shown in the figure below, determine the internal loadings at points D and. Consider the weight of the beamwhich is SN lbs per ft complete solution and drawing. if u can please add some explanation thankyou FN = 49 MN = 101 SN = 94
In a 2.5 cantilevered I-beam, 2500 kg weight is applied at 0.75 meter from the free end. If the allowable stress in beam is 120 Mpa, determine the section modulus and The base and height of the beam if the base is 75% of its height mm.
An aluminum wire 3.0 m in length and 4.0 mm in diameter supports a 1000 N mass. Determine the stress in the wire.
The section modulus for the beam of rectangular cross section of size 80 mm x 85 mm, is ______________ mm3. The section modulus (unit is in mm3)= ______________ Answer
The composite shaft, consisting of aluminum, copper, and steel sections, is subjected to the loading shown. Determine the displacement of B with respect to C. The cross-sectional area and modulus of elasticity for eachsection are shown in the figure. Neglect the size of the collars at B and C.
consider the beam shown in. EI is constant. assume that EI is in kip * ft2. determine the expression for the elastic curve using the coordinate x1 for 0 < x1 < 20 ft, where x1 is in feet. v1 in ft answer in terms of the variables x1, E and I. determine the expression for the elastic curve using the coordinate x2 for 0 < x2 < 10 ft where x2 is in feet. v2 in ft. answer in terms of the variables x2, E and I. specify the deflection of the beam at C. vc in ft. answer in terms of E and I. specify the slope at A, measured counterclockwise from the positive x1 axis. Theta A in rad. answer in terms of E and I.
Material A (shown below) is experiencing forces shown below at different points along its body. If the area of its cross section is equal to 0.35 in^2, determine the total new length of the material if modulus of elasticity is equal to 5x10^6 psi. AB =4 ft BC =4.5 ft, CD = 3.5 ft. Note: Final Answer in 4 decimal places.
The three-bar truss in Fig. a is subjected to a horizontal force of 5 kip. If the cross-sectional area of each member is 0.20 in2, determine the horizontal displacement at point B. E = 29(103) ksi.
a) A simply supported beam has a symmetrical rectangular cross-section. If the second moment of area (I) of a beam with a rectangular cross-section is11.50 x 106 mm4 about its centroidal x-axis and the depth dimension (d) of the rectangular section is 180 mm, determine the breadth dimension (b) for this beam section. Give your answer in millimetres (mm) and to 2 decimal places. Assume the beam section material is homogeneous. b) The same rectangular cross-section beam in Q2b is subjected to a maximum bending moment of 25,000 Nm and experiences sagging. Assuming that the centroidal axis passes through the beam section at (d/2), calculate the maximum bending stress (σmax) the beam will experience. Give your answer in N/mm2 and to 2 decimal places.
a) A simply supported beam has a symmetrical rectangular cross-section. If the second moment of area (I) of a beam with a rectangular cross-section is11.50 x 106 mm4 about its centroidal x-axis and the depth dimension (d) of the rectangular section is 180 mm, determine the breadth dimension (b) for this beam section. Give your answer in millimetres (mm) and to 2 decimal places. Assume the beam section material is homogeneous. b) The same rectangular cross-section beam in Q2b is subjected to a maximum bending moment of 25,000 Nm and experiences sagging. Assuming that the centroidal axis passes through the beam section at (d/2), calculate the maximum bending stress (?max) the beam will experience. Give your answer in N/mm2 and to 2 decimal places.