O a. Students cannot put a chemical directly on the balance pan. O b. Solid waste can be disposed in the sink. O c. If acid is spilled on your skin, wash it immediately and thorougly with soap and warm water. O d. Students should'nt remove shared chemicals from their original locations. O e. Pipettes and droppers should not be inserted into reagent bottles.

O a. Students cannot put a chemical directly on the balance pan. O b. Solid waste can be disposed in the sink. O c. If acid is spilled on your skin, wash it immediately and thorougly with soap and warm water. O d. Students should'nt remove shared chemicals from their original locations. O e. Pipettes and droppers should not be inserted into reagent bottles.

Introductory Chemistry: A Foundation

9th Edition

ISBN:9781337399425

Author:Steven S. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Donald J. DeCoste

Chapter1: Chemistry: An Introduction

Section: Chapter Questions

Problem 13ALQ

See similar textbooks

Similar questions

True or False: The accuracy of a buret is to 0.05 mL. True or False: Burets are stored with distilled water to help prevent against corrosion of the inside of the glass tube.
THE QUESTION IS AT THE PICTURE... 1 QUESTIONS ONLY.. AND THE GIVEN PROBLEMS IS THE ONE I TYPEDA. Concentration1. Place 3 mL each of 6N, 3N, & 1.5N hydrochloric acid in separate test tubes.2. Drop simultaneously equal lengths (about 1cm) of magnesium ribbon and note thetime it takes for the magnesium to dissolve in each use.B. Surface Area1. Weigh a small iron nail to the nearest hundredths of a gram and weigh an equalamount of iron fillings.2. Place them in a separate test tubes.3. Add simultaneously 3 mL of 3N hydrochloric acid and compare the rates of reaction.C. Temperature1. Place 5 mL each of 0.1N sodium thiosulfate solution into 5 test tubes.2. Place all five test tubes in the water bath and let it stand for 1 minute.3. Record the temperature of the water bath. Remove the first test tube from thewater bath and place it in the test tube rack.4. Add 1 mL of 0.1M sulfuric acid and stir with a glass rod. Record the time it takes forthe turbidity to appear.5. Increase the…
What substances did not pass through the filter paper?
What specific material(s) is (are) used and what specific properties this (these) material(s) possess(es) in order for the cellphone/digital camera batteries to function properly? write a short essay in which you report your findings.
What hazardous byproducts are created in pulp mill effluent treatment processes? If possible links to references on processes.
When jump-starting a car with a dead battery, the ground jumper should be attached to a remote part of the engine block. Why?
Trye or false? information about the hazards of a particular chemical can be obtained from a document referred to as a SDS. The first aid for chemicas gotten in eyes or on skin is to wash the eyes or skin immediately with water for at least 15 minutes. safety goggles are to be worn in the laboratory by all whenever chemicals arw used in the laboratory.
Adhesives are used widely in industries as well as in daily live. They are considered temporarily assembly method. O permanent assembly method. O one of the processing operations. () none of the above. O
Please clearly label the following where they appear: pinacol, sulfuric acid, water, pinacolone, direction of water flow, keck clips, metal clamps, thermometer positioning, heat source, and list any hazards or important notes for this set up.
A 0.9092 g sample of wheat flour was analysed by the Kjeldahl procedure. The ammonia formed was distilled into 50.00 mL of 0.02532 M H2SO4. A 7.46 mL backtitration of 0.04917 M NaOH was required. (Note the stoichiometry of your acid and base) Calculate thea. %N (FM=14.007) in the sample,b. %Protein in the sample (factor = 5.70)
A 0.53 g sample containing KBr (MW=119) is dissolved in 50 mL of distilled water. Titrating with 0.04614 N AgNO3 requires 28.5 mL to reach the endpoint. Calculate the %w/w KBr in the sample. (Round-off your answer to 2-decimal places) Answer = ____%
What volume of 0.10 M H2C2O4 would be required to remove the rust stain weighing 1.0 grams?