Problem 2The containers A and B, shown on the figure, are filledwith water, with density Pwater = 1000 kg/m³. The pressure inBH00,5mcontainer A is PA= 40 kPa. The two containers are connected1,5mwithinclined U-shaped liquid manometer, with0,5manmanometric fluid density Pmanometric = 2600 kg/m³. Determinethe pressure in container B, considering the shown geometryon the figure.Manometricfluid

Answered: Image /qna-images/answer/0c2c305d-f3c5-438d-9fad-852633063cf0.jpg

Problem 2 The containers A and B, shown on the figure, are filled HO with water, with density Pwater = 1000 kg/m³. The pressure in 0,5m container A is pa = 40 kPa. The two containers are connected %3D B H0 1,5m with inclined U-shaped liquid manometer, with 0,5m an manometric fluid density pmanometric = 2600 kg/m³. Determine the pressure in container B, considering the shown geometry on the figure. Manometric fluid

Problem 2 The containers A and B, shown on the figure, are filled HO with water, with density Pwater = 1000 kg/m³. The pressure in 0,5m container A is pa = 40 kPa. The two containers are connected %3D B H0 1,5m with inclined U-shaped liquid manometer, with 0,5m an manometric fluid density pmanometric = 2600 kg/m³. Determine the pressure in container B, considering the shown geometry on the figure. Manometric fluid

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

You have a rectangular box 1.5m long, 0.8m wide and 0.6m high. How many gallons of water can it hold? (1.0 gal = 0.134ft^3 and 1.0m = 3.281 ft)
Q.5 Determine the volumetric flow of water in m3/hr flowing in a pipehaving a diameter of 40 mm through an orifice having a diameter of 20 mm.Manometer reading across the tapping is 15 cm of Hg. Assume correctionfactor = 1. Reynolds number Ra is 105 . Assume density of water = 1000 kg/m3and kinematic viscosity is 10–2 stokes (cm2/sec). Also calculate the pressuredifference at the tappings. Assume Cd = 0.61.
SHOW COMPLETE SOLUTION AND FINAL ANSWER INTO 3 DECIMAL PLACES 3. A large pipe called penstock in hydraulic work is 1.5 m in diameter. Here it is composedof wooden staves bound together by steel hoops each 300 mm2in cross sectional area, and is used to conduct water from a reservoir to a powerhouse. If the maximumtensilestress permitted in the hoops is 130 MPa, what is the maximum spacing between hoops under a head of water of 30m? Use density of water equal to 1000 kg/m3
Water flows through a pipe at 152 L/s that changes gradually in diameter from 196 mm at point A to 456 mm at point B. Point B is 6 m higher than point A. The pressures at point A and point B are 126 kPa and 69.3 kPa, respectively. Assume that the datum line passes through point A. Which of the following most nearly gives the head loss in the pipe? (m). Round your answers in 3 decimal places.
1. THERE IS A LEAK IN A HORIZONTAL 300 MMDIAMETER PIPELINE. UPSTREAM FROM THE LEAK TWOGAGES 600 METER APART SHOWED A DIFFERENCE OF140 ???. DOWNSTREAM FROM THE LEAK TWO GAGES600 METER APART SHOWED A DIFFERENCE OF 126??? . ASSUMING ? = 0.025. HOW MUCH WATER ISBEING LOST FROM THE PIPE. show answer in litre per sec
A liquid is flow throw Rotameter to a tank of size ( L x W x H ) and it is required to full the tank to level of H as shown in Figure . What time is required to full the tank by this liquid ? What time is required to drop the liquid in the tank to from level H to D by rectangular notch ?
Show complete solution. Units must be included in all calculations. All numerical values should be rounded off to the nearestthousandths. 2.If the velocity in a 12-in pipe is 1.65 ft/s, what is the velocity in a 3-in-diameter jet issuing from a nozzleattached to the pipe?
Based on the layout of the water supply system, as show in Figure 1, flow through the delivery pipe, Q = 2.50 cfs and diameter of the pipe, D = 2.65 inch with e = 0.015 inch. Ingore the minor pressure losses and use the following formulae to calculate the major pressure losses. The velocity of flow through the pipe and the friction factor, f, range are estimated to be nearly. Use g = 62.4 lb/ft^3 for water and use Moody's diagram. Water temperature is 20°C (68°F).
Water flows in a Venturi meter shown at a rate of 1.49 ft3/s and the differential gage isdeflected as shown. If the SG of the gage liquid is 1.25, compute the following:a) the difference in pressure from A to B (psi),b) velocity at the throat (ft/s), andc) the coefficient of the venture meter.
A 12-inch by 6-inch Venturi meter is installed in a vertical pipeline carrying water as shown inthe Figure C. The flow is upward through the meter. A differential manometer containing fluid,with sp.gr 1.67, is attached to inlet and throat, the difference z in gage levels being 5.76 ft.Neglecting loss of head, write energy equation from inlet to throat of meter. Also write stepby step equation of the differential gage between inlet and throat and combine the twoequations to compute the discharge
Theflowrateofwaterthroughacastironpipeis5000GPM.The diameter of the pipe is 330mm, and the coefficient of friction is f=0.0173. What is the pressure drop over a 30m length of pipe
Show all problem solution's steps. Direct formula substitution solutions will have NO CREDIT POINTS. 1. A 75 mm diameter fire hose discharges water through a nozzle having a jet diameter of 25 mm. The lost head in the nozzle is 25% of the velocity head in the jet. If the pressure at the base of the nozzle is 625 KPa: compute the discharge in m3/min; the maximum horizontal range to which the stream can be thrown; the maximum vertical reach, and the diameter of the jet at a point two-third of the maximum vertical reach from the tip of the nozzle. Neglect air resistance.