One - half length of 50 mm diameter steel rod is solid while the remaining half is hollow having a bore of 25 mm. The rod is subjected to equal and opposite torques at its ends. If the maximum shear stress in solid portion is S, the maximum shear stress in the hollow portion is

One - half length of 50 mm diameter steel rod is solid while the remaining half is hollow having a bore of 25 mm. The rod is subjected to equal and opposite torques at its ends. If the maximum shear stress in solid portion is S, the maximum shear stress in the hollow portion is

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.4.5P: A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions...

See similar textbooks

Related questions

Q: The angular velocity of link BC. The angular velocity of triangular plate ABD. The velocity magnitud...

A: Given: Angular velocity of link AO is 3 rad/s CW To determine: Angular velocity of link BC Angular...

Q: The first element in a feature control frame in Solidworks denotes what?

A: The products may vary slightly in terms of dimensions as compared to the initial designs because of ...

Q: 16-69. Rod AB is rotating with an angular velocity of WAB = 60 rad/s. Determine the velocity of the ...

A: vB=ωAB×rABvB=(60K)×(-0.3sin60°i+0.3cos60°j)vB=-9i-93j m/s For rod BC Vc=VB+ωBC×r-vcj=(-9i-93j)+(ωBCK...

Q: For each of the plates and loadings shown, determine the reactions at A and B.

Q: Two uniform cylinders, each of mass m = 6 kg and radius r = 125 mm, are connected by a belt as shown...

A: Given Data Mass of each cylinder is: m=6 kg Radius of each cylinder is: r=125 mm=0.125 m (a) The v...

Q: 2. A stone is dropped into a well and 4 seconds later, the sound of the splash is heard. If sound tr...

Q: *4-28. Due to an unequal distrihation of fuel in the wing tanks, the centers of gravity for the airp...

A: Apply condition of equilibrium ∑Fy=0D+E+F-WA-WB-Wc=0D+E+F-225-40-30=0D+E+F=295 KN∑My=0 WA(1.2+0.9)+W...

Q: Hot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates. The gas at 220°C flows in pa...

Q: draw a shear and bending moment diagram for the beam shown. Label each diagram with values at locati...

A: Given Draw a sheer and bending moment diagram for given figure

Q: Mechanical Engineering Question

A: Note:As per our guidelines we are supposed to answer only one question. Kindly repost other questi...

Q: Determine the amount of force the two supports of the shelf need to exert in order to keep the plate...

Q: Determine the tension in the cables AB and AC , if the tension in the cable AD is 200 lb and for h v...

A: Given, The tension in the cable AD is 200 lb From the figure, we can find that, tanα=124α=tan-13=71...

Q: QB2: Determine the force in members GH, GB, and BC, and state whether each of these three members is...

Q: A sharp-crested triangular weir with a notch angle of 80° is used to measure the discharge rate of w...

A: Given Data The sharp-crested triangular weir with a notch angle of 80° For Sharp crested triangular...

Q: The water in a large lake is to be used to generate electricity by the installation of a hydraulic t...

Q: The box with a force of 40 N can be made with the help of three ropes as shown in the figure.It is h...

Q: What are the two micro-scale plasticity mechanisms active in amorphous polymers? Are they likely to ...

A: The two micro-scale plasticity mechanisms active in amorphous polymers are shear banding and crazing...

Q: Figure Q2 shows a statically determinate plane truss subjected to a vertical and horizontal concentr...

A: Draw the free body diagram of the system as shown below.

Q: . To design a beam why do we require applications of shear and flexure formulas?

A: To design a beam we need to find out the bending moment and shear force And these two quantities ar...

Q: 2. Explain the principle of strain gauge? Write done any two application of strain gauge in mechanic...

A: Strain gauge is one of the significant sensors used in geotechnical field for the measurement of str...

Q: It has been estimated that a minimum run off of approximately 94 m3/sec will be available on a hydra...

Q: Due to a fabrication error, the inner circle of the tube is eccentric with respect to the outer circ...

A: The expression for the average stress of the outer circle is, τavg=V2tAV=τavg×2tA=τavg×2×(a-b)×π×a+b...

Q: As shown in the figure, A and B are sliding along the horizontal bar with velocities VA = 2 m/s and ...

A: Draw the velocity diagram of the system. Here, the velocity bars ac and bc are perpendicular to the...

Q: The aluminum rod AB (G=36 GPa) is bonded to the brass rod BD (G=51 GPa). Knowing that portion ...

A: For aluminum rod AB (Ga=36 GPa)=36×109 PaFor brass rod BD (Gb=51 GPa)=51×109 PaNow for rod ABMx=08...

Q: Determine the magnitude and direction of the resultant for system of forces shown in the figure. Tak...

Q: 8-23. The plug has a diameter of 30 mm and fits within a rigid sleeve having an inner diameter of 32...

A: Given: The diameter of the plug is dp=30 mm=0.03 m. The diameter of the sleeve is ds=32 mm=0.032 m....

Q: answer 96,97,98

Q: T or F -The α-phase is rich in iron. -The cementite phase is rich in iron -Pearlite steel has a l...

A: Answer 1. The α-phase is rich in iron is true. Reason: The α-phase having the least carbon percentag...

Q: A hollow mast of circular section as shown is to be stiffened by bonding two strips of the same mate...

Q: In a manufacturing process, a large, cylindrical roller is used to flatten material fed beneath it. ...

A: Note: As per our guidelines we are supposed to answer only the first 3 sub-parts. Kindly repost othe...

Q: Concept Revolves around Friction

A: Pulling and pushing of a heavy packing case, the force required to slide it is smaller while pulling...

Q: Two baseballs of diameter 7.35 cm are connected to a rod7 mm in diameter and 56 cm long, as in Fig. ...

A: Given data: The diameter of baseball, db = 7.35 cm. The diameter of the rod, dr = 7 mm. The total l...

Q: 10. MC Critical damping is defined as a. C, = 2sqrt(km) b. C = sqrt(k/m) c. C = k/m d. C, = k/m? 'cr...

Q: Series of free-body diagrams and equilibrium equations to determine important reactions/loads impart...

A: Consider the free body diagram of the handle as shown below.

Q: 20 The particular integral for an damped single degree of freedom system subjected to a harmonic for...

Q: Member ABC is supported by a pin and bracket at B and by an inextensible cord attached at A and C an...

A: Free body diagram

Q: A main pipe of 150 mm diameter is branched into two pipes of 75 mm diameter each as shown. The branc...

Q: Maximum shear stress developed on the surface of a solid circular shaft under pure torsion is 235 MP...

Q: The 2 kg physics book in figure is connected by a string to a 0.2 kg coffee cup. The book is given a...

Q: J. Plot the variation of the maximum weight of the cylinder F for the system to remain in equilibriu...

A: let the weight of the cylinders E and F in the general case be E and F respectively. As per the give...

Q: answer 81-82

Concept explainers

Torsion

In mechanical engineering, torque, torsion, and twisting moment are three of the most important concepts which have different meanings. Torque is the consequence of a moment of a force that produces an angular acceleration in a body or induces rotational kinetic energy in a body. For instance, in an automobile, the power transmission shaft is a body that is always under rotation due to the external torque acting on it, this torque is created by the engine.

Question

One - half length of 50 mm diameter steel rod is solid while the remaining half is hollow having a bore
of 25 mm. The rod is subjected to equal and opposite torques at its ends. If the maximum shear stress in
solid portion is S, the maximum shear stress in the hollow portion is

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
Solve the preceding problem if the length L = 56 in., the inner radius r1— 1.25 in., the angle of twist is 0.5°, and the allowable shear strain is 0.0004 rad.
A circular steel tube with an outer diameter of 75 mm and inner diameter of 65 mm is subjected to torques 7"at its ends. Calculate the maximum permissible torque 7jliajl if the allowable normal strain is ea= 5 X 10"4 Assume that G = 15 GPa.
Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the adequacy of both the pipes. In the test, the pipe structure is fixed at A, a concentrated torque of 500 kN - m is applied at x = 0.5 m, and uniformly distributed torque intensity t1= 250 kN m/m is applied on pipe BC. Both pipes have the same inner diameter = 200 mm. Pipe AB has thickness tAB=15 mm, while pipe BC has thickness TBC= 12 mm. Find the maximum shear stress and maximum twist of the pipe and their locations along the pipe. Assume G = 75 GPa.
A solid circular shaft AB of diameter d is fixed against rotation at both ends (sec figure), A circular disk is attached to the shaft at the location shown. What is the largest permissible angle of rotation 0max of the disk if the allowable shear stress in the shaft is Tallow? [Assume that a >b. Also, use Eqs. (3-50a and b) of Example 3-9 to obtain the reactive torques.]
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
A solid brass bar of diameter d = 1.25 in. is subjected to torques T1as shown in part a of the figure. The allowable shear stress in the brass is 12 ksi. What is the maximum permissible value of the torques T1? If a hole of diameter 0.625 in. is drilled longitudinally through the bar, as shown in part b of the figure, what is the maximum permissible value of the torques T2? What is the percent decrease in torque and the percent decrease in weight due to the hole?
The steel axle of a large winch on an ocean liner is subjected to a torque of 1.65 kN · m (see figure). What is the minimum required diameter dminif the allowable shear stress is 48 M Pa and the allowable rate of twist is 0.75º/m? (Assume that the shear modulus of elasticity is 80 G Pa.) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d/8, Compare dminvalues to corresponding values from part (a)
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
Solve the preceding problem if the shaft has an outer diameter d2=150 mm and inner diameter d1= 100 mm. Also, the steel has a shear modulus of elasticity G = 75 GPa, and the applied torque is 16 kN ·m.