Outdoor air conditions are: 28°C db, 19.5°C wb Return air conditions are: 22°C db, 50% RH. The mixture air condition outlet the cooling coil are: 10°C db, 0.00735 kg/kgda Draw the system on the Psychrometric chart, then calculate: 1. Cooling coil load. 2. Room sensible heat. 3. Room latent heat. 4. Fresh (outdoor) load. 5. Duct and fan heat gain 6. Sensible heat ratio SHR. If the supply air temperature increases with a value 1°K due to fan motor heat gain and 2°K due to duct heat gain.

Outdoor air conditions are: 28°C db, 19.5°C wb Return air conditions are: 22°C db, 50% RH. The mixture air condition outlet the cooling coil are: 10°C db, 0.00735 kg/kgda Draw the system on the Psychrometric chart, then calculate: 1. Cooling coil load. 2. Room sensible heat. 3. Room latent heat. 4. Fresh (outdoor) load. 5. Duct and fan heat gain 6. Sensible heat ratio SHR. If the supply air temperature increases with a value 1°K due to fan motor heat gain and 2°K due to duct heat gain.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1.1 Determine the electrical power supplied to a boiler when the temperature of the enteringwater is 20 C and the exiting temperature is 89 C. The flow of.the pressured water is 2 Kg/s. There is anegligible pressure drop through this boiler and it operates at a constant pressure of 3 bars. The specificheat is c = 4,370 J/(Kg K). There is a 1.5(105) W rate of heat loss from the boiler during this process to asurrounding at 293.2 k. Consider steady state conditions.1.2 Calculate the total rate of entropy production in Problem 1.1.1.3 Calculate the total rate of exergy destruction (W) in Problem 1.1. The dead statetemperature is 293.2 K and pressure is 1 bar.1.4 Calculate the mass flowrate of fuel (natural gas, CH4) required to heat the water flow to theconditions of problem 1.1 if the electrical heating device is replaced with a gas fired boiler. The highheating value (HHV) of the fuel is 50.02 MJ/kg.1.5 Calculate the exergy destroyed in the process described by problem 1.4. The exergy…
An ice plant produces 10 tons of ice per day at 0°C using water at room temperature of 33°C. Estimate the power rating (Electrical Power consumed by the motor to run compressor) of the compressor-motor, if the C.O.P. of the plant is 3.0 and overall electro-mechanical efficiency (η) is 91%. Note: Latent heat of ice is 335 kJ/kg, Cp = 4.18 kJ/kg.K.
A vapour compression refrigerator circulates 4.5 kg of NH3 per hour. Condensation take place at 30°C and evaporation at – 15°C. There is no under-cooling of the refrigerant. The temperature after isentropic compression is 75°C and specific heat of superheated vapour is 2.82 kJ/kg K. Determine : (i) Co-efficient of performance. (ii) Ice produced in kg per hour in the evaporator from water at 20°C and ice at 0°C. Take : Enthalpy of fusion of ice = 336 kJ/kg, specific heat of water = 4.187 kJ/kg. (iii) The effective swept volume of the compressor in m3 /min.
A single-acting, single-cylinder air compressor is rated at 4.25 m3/min of air. The suction conditions are 1 atm and 27 C and discharge pressure is 1034 kPa. The compression process follows the equation PV1.35 = A. Determine the power, in kW, required to compress the air. B.)what is the engine kW power needed to drive the unit if the combined engine-compressor efficiency is 84%? C.)if the compressor is to run two-stage at optimum intercooler pressure with perfect intercooling, what will be percentage of power saved?
Steam enters the condenser of a steam power plant at a flow rate of 18000 kg/h, a degree of dryness of 0.86 and a pressure of 15 kPa, leaving the condenser as a saturated liquid at the same pressure.A nearby river water is used for the cooling of the condenser.Calculate the water flow rate of the cooler if the water of the river can be heated up to 10°C in order to avoid thermal pollution. (Cp,su=4,18 kj/kgK) (Note: the potential energy change is negligible.)
An auditorium is to be maintained at a temperature of 26℃ DB and 50% RH. Air is to be supplied at a temperature not lower than 15℃ DB. The sensible heat gain is 110 kW and the latent heat gain is 37.5 kW. Take the outdoor ventilating air as 25% by weight of the air from the room (meaning 75% of the airconditioned supply air is recirculated) and is at 35℃ DB and 60% RH. Determine the refrigerating load in Tons of Refrigeration (TR).
Design, analyze, and optimize a triple pressure heat recovery steam generator (HRSG) for a large advanced combined cycle power plant whose net steam power output is 150 MW. The gas turbine exhaust gases can be treated as ideal gases and the outlet temperature and mass flow rate are 550°C and 500 kg/s respectively. Water enters a low-pressure economizer for this HRSG at P = 200 kPa and T = 40°C. Make reasonable assumptions as required.
The cooling load of a cold store is 24kW, the evaporator temperature is -10 ° C, the condenser temperature is 40 ° C. R134a is used as the refrigerant. Calculate the mass flow rate, the power consumed by the compressor, the cooling effect coefficient and coefficient according to all these data. (compressor characteristics Heating effect hik (compressor internal efficiency) = 0.75, hmk (mechanical efficiency) = 0.80, hec (electric efficiency) = 0.97 and hkk (belt pulley efficiency) = 0.95) motor
A performance test of an ice plant gave the following data: Capacity: 20 tons of ice/day Refrigerant: Ammonia Condenser pressure: 1391.5 kPa Evaporator pressure: 208.26 kPa Raw water temperature: 32OC Harvest temperature: -7OC Block of ice: 300 lb/block The compressor is twin-cylinder, single acting, D/L = 1.25, 450 rpm, mechanical efficiency is 80%. Additional heat load due to infiltration and conduction is 20%. Determine: a) Number of cans needed b) Product cooling load c) Refrigerating capacity in tons of refrigeration d) Amount of refrigerant flow e) Size of motor to drive the compressor f) Bore diameter and length of stroke
1. A heat exchanger is located on the roof of a warehouse to heat the air in winter. It is a coil-shaped pipe into which water vapor enters at 0.1 MPa and 300 °C and leaves with a quality of 30%. The warehouse has the following dimensions: 80m x 160m x 10m. The air must be heated from 5°C to 22°C. a. What must be the mass flow rate of the water to heat the air in less than half an hour? b. We want to cool the steam from the exchanger outlet and bring it up to 50 °C. For this, a mixing chamber with water at 20 °C is used, what will be the proportion of the steam mixture? c. The exchanger is damaged and only liquid water can be used at the same pressure (inlet T. 1 °C below saturation and outlet T. at 30°C). How long does it take to heat the air with the same flow of water?
A refrigerator with tetrafluoroethane as refrigerant operates with an evaporation temperature of −25°C and a condensation temperature of 26°C. Saturated liquid refrigerant from the condenser flows through an expansion valve into the evaporator, from which it emerges as saturated vapor. (a) For a cooling rate of 5 kJ·s−1, what is the circulation rate of the refrigerant? (b) By how much would the circulation rate be reduced if the throttle valve were replaced by a turbine in which the refrigerant expands isentropically?
. A meeting hall is to be maintained at 25°C, 18Cwb. The space has a cooling load of 40kW of which 32kW is sensible cooling load. The temperature of the supply air to the space must not be lowered than 18°C. Outdoor conditions are 35°C, 50% RH. Assume that 75% by weight of the supply air from the room is recirculate but a portion of these bypassed the cooling equipment. Determine a) amount of air supplied to the space b) TOR required of the cooling equipment c) average cooling coil surface temperature.