P' 120 mm 80 mm

Q: An aluminum [E = 10000 ksi] control rod with a circular cross section must not stretch more than…

A:

Q: For the connection shown, the average shear stress in the 16-mm-diameter bolts must be limited to…

A: Givend=16mmAverage shear stress=260Mpa

Q: For the connection shown, the average shear stress in the 14-mm-diameter bolts must be limited to…

A: Given is a double shear connection.

Q: In the steel structure shown, a 6-mm-diameter pin is used at C and10-mm-diameter pins are used at B…

A: Given Data: The ultimate shear stress is:τul=150 Mpa The ultimate normal stress is: σul=400 MPa.…

Q: 1. The structure is used to support a distributed load of w = 15 kN/m. The bolts at A, B, and C each…

A:

Q: For the connection shown, the average shear stress in the 15-mm-diameter bolts must be limited to…

A:

Q: Knowing that, for the plate shown, the allowable stress is 125 MPa, determine the maximum allowable…

A: Given Allowable stress =125 MPa Fillet radius a) 12 mm b) 18 mm To find Maximum value of P

Q: Knowing that the allowable stress in section ABD is 80 MPa, determine the largest force P that can…

A:

Q: Straight rods of 0.30-in. diameter and 200-ft length are sometimes used to clear underground…

A: (a) The radius of the rod is given as, Moment of inertia is written as, The diameter of the spool…

Q: A fabric used in air-inflated structures is subjected to a biaxial load-ing that results in normal…

A: Given data: The normal stress in the x-direction is; σx = 120 MPa. The normal stress in the…

Q: [2.37] The 1.5 m concrete post is reinforced with six steel bars, each with 28 mm diameter. Knowing…

A:

Q: Two wooden members of uniform cross section are joined by the simple scarf splice shown. Knowing…

A:

Q: A cast-iron machine part is acted upon by the 3 kN-m couple shown. Know-ing that E= 165 GPa and…

A: Given data Couple acting on the machine part, M = 3 kN-m. Draw the cross-section of the beam,…

Q: Knowing that, for the plate shown, the allowable stress is 136 MPa, determine the maximum allowable…

A: given data, allowable stress =136MPa diameter DA = 20mm db = 50 mm p max? when no stress…

Q: Knowing that the allowable stress in section ABD is 10 ksi, determine the largest force P that can…

A: Given data: The allowable stress in the section ABD is; σallow=10 ksi. Evaluate the cross-section…

Q: A steel plate 5/16 in. thick is embedded in a horizontal concrete slab and is used to anchor a…

A: Given data t=516 in=0.3125 indhole=34 in=0.75 inσu=36 ksiτ=300 psiFOS=3.6P=2.5 kips

Q: The boom AB is made up of a hollow square 100-mm tube having a wall thickness of 5 mm. A 10-mm…

A: Given data, Outer dimension of hollow boom AB is 100 mm and thickness is 5 mm. So, cross-sectional…

Q: A timber beam AB of length L and rectangular cross section carries a single concentrated load P at…

A: (a) Given Data Length of AB is : L Load at midspan is : P Area of cross-section is : A=b×h Now due…

Q: The ABC element is supported by a pin at C and a BD cable. Knowing that the limit load for the BD…

A:

Q: The lap joint shown is connected by 6 pieces rivets. Assuming that the load P = 70 KN is carried…

A: Given Data Applied load is: P=70 kN=70000 N. Number of rivets are: n=6 Allowable shear stress is:…

Q: In the structure shown, an 8-mm diameter pin is used at A, and 12-mm diameter pins are used at B and…

A:

Q: |275 kN B (a) Knowing that o =160 MPa and 7 =100 MPa, select the most economical metric wide-flange…

A: Consider the free body diagram: Taking moment about Point C:RB*3.6=275*5.1+275*1.5RB=504.17 KN…

Q: Two forces P can be applied separately or at the same time to a plate that is welded to a solid…

A: Given data as per the question forces applied on the solid rod =P, P (a) when both forces…

Q: Three wooden planks are fastened together by a series of bolts to form a column. The diameter of…

A: Given data dblt=0.012 mσmax=36×106 psi

Q: For the clevis connection shown, the shear stress in the 5/16-in.-diameter bolt must be limited to…

A: To Find : The maximum load P. Given :  The shear stress is τ=20 ksi. The diameter is d=516 in. FBD:…

Q: A 1.50-in.-diameter brass [G = 5800 ksi] rod is used as a shaft. Determine the thickness of hollow…

A: d=1.50 in Gbrass=5800 ksi Gsteel=11200 ksi τmax=7200 psi τmin=9600 psi

Q: 125 mm 75 mm 1.32 Two wooden members of uniform cross section are joined by the simple scarf splice…

A: Given data:

Q: The frame shown consists of four wooden members, ABC, DEF, BE,and CF. Knowing that each member has a…

A: The free body diagram of the wooden members is as follows: Calculate the moment about the point A…

Q: PROBLEM 7.20 Two members of uniform cross section 50x 80 mm are glued together along plane a-a that…

A: Any action that can change the state of motion is called force. Force is described by its magnitude,…

Q: 1.55 In the structure shown, an 8-mm-diameter pin is used at A, and 12-mm-diameter pins are used at…

A:

Q: Knowing that the allowable stress in section ABD is 70 MPa, determine the largest force P that can…

A:

Q: The rigid bar ABD is connected to the rod BD which consists of a single bar with a width of 25,0 mm…

A:

Q: 5. The load P applied to a steel rod is distributed to a timber support by an annular washer. The…

A: Given:stress in steel rod, σst=35 MPaDiameter of rod, dr=22 mmInner diameter of washer, di=25…

Q: 1. A steel plate 5 /16 in. thick is embedded in a horizontal concrete slab and is used to anchor a…

A:

Q: 1.53 In the steel structure shown, a 6-mm-diameter pin is used at C and 10-mm-diameter pins are used…

A:

Q: For the connection shown, the average shear stress in the 15-mm-diameter bolts must be limited to…

A:

Q: Knowing that the central portion of the link BD has a uniform cross-sectional area of 1350 mm,…

A: To determine the magnitude of force P.

Q: Two wooden members of uniform rectangular cross section of sides a = 100 mm and b = 60 mm are joined…

A:

Q: The steel tie bar shown is to be designed to carry a tension force of magnitudeP=120 kN when bolted…

A: a) Diameter of bolt    Since bolt is in double shear ,    F1=12P=60 KN    ⟌=F1A; 60π4d2…

Q: Knowing that the clamp shown has been tightened on wooden planks being ghued together until P= 900…

A:

Q: Two wooden members of uniform cross section are joined by the simple scarf splice shown. Knowing…

A:

Q: Two L4 x 3 rolled-steel angles are bolted together and used to sup-port the loading shown. Knowing…

A: Draw the free body diagram.

Q: mpostE bar Is made up of a brass rod of 20 mm diameter that enclosed in a steel tube with outer…

A:

Q: A glue-laminated column of 3-m effective length is to be made from boards of 24 x 100-mm cross…

A:

Q: A14-kN tensile load will be applied to a 50-m length of steel wire with E = 200 GPa. Determine the…

A: Given data:

Q: B The steel tie bar shown is to be designed to carry a tension force of magnitude P = 120 kN when…

A:

Q: Two horizontal 5-kip forces are applied to pin B of the assembly shown. Knowing that a pin of…

A:

Q: In the structure shown, an 8-mm-diameter pin is used at A and 12 mmdiameter pins are used at B and…

A: Draw free body diagram of links  and . In addition, draw free body diagrams of pins ,  and . Here,…

Q: For the connection shown, the average shear stress in the 17-mm-diameter bolts must be limited to…

A:

Q: Two wooden members of uniform cross section are joined by the simple scarf splice shown. Knowing…

A: