125 mm 75 mm 1.32 Two wooden members of uniform cross section are joined by the simple scarf splice shown. Knowing that the maximum allowable tensile stress in the glued splice is 500 kPa, determine (a) the largest load P that can be safely supported, (b) the corresponding shearing stress in the splice. 60

125 mm 75 mm 1.32 Two wooden members of uniform cross section are joined by the simple scarf splice shown. Knowing that the maximum allowable tensile stress in the glued splice is 500 kPa, determine (a) the largest load P that can be safely supported, (b) the corresponding shearing stress in the splice. 60

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two wooden members of uniform cross section are joined by the simple scarf splice shown. Knowing that the maximum allowable tensile stress in the glued splice is 90 psi, determine the largest load P that can be safely supported if W = 2.4 in, L = 8.2 in and θ= 51.8. Round off the final answer to two decimal places.
A14-kN tensile load will be applied to a 50-m length of steel wire with E = 200 GPa. Determine the smallest diameter wire that can be used, knowing that the normal stress must not exceed 150 MPa and that the increase in length of the wire must not exceed 25 mm. The smallest diameter that can be used is ___mm?
The five-bolt connection shown must support an applied load of P = 214 kN. If the average shear stress in the bolts must be limited to 249 MPa, determine the minimum bolt diameter that may be used in the connection.
An aluminum plate (E= 74 GPa, ν= 0.33) is subjected to a centric axial load that causes a normal stress σ. Knowing that, before loading, a line of slope 2:1 is scribed on the plate, determine the slope of the line when σ=125 MPa.
Two gage marks are placed exactly 250mm apart on a 12mm-diameter aluminum rod with E=73Gpa and an ultimate strength of 140Mpa. Knowing that the distance between the gage marks is 250.28mm after a load is applied, determine (a) the stress in the rod, (b) the factor of safety.
THe bracket shown is made of cold drawn steel with Sy=400MPa and Su=480 MPa, and is fastened to a beam made of the same material by five rivets that are made of a steel with Sy=300 MPa and Sut=365 MPa. The thickness of the bracket and the beam are 12 mm and 16 mm respectively.Diameters of the rivets are 20 mm. What safe load F(steady) can be supported by the riveted joint for a factor of safety of 2. Use distortion energy theory of failure.
The lap joint shown is connected by three 16-mm diameter rivets. If the allowable stress for shear in rivets is 40 MPa and bearing between therivets and the plates is 60 MPa determine the safe load P.
Two wooden members of uniform cross section are joined by the simple scarf splice shown. Knowing that the maximum allowable tensile stress in the glued splice is 82.4 psi, determine the largest load P that can be safely supported if W = 4.5 in, L = 8.9 in and θ= 55.3
Knowing that a 0.02-in. gap exists when the temperature is 75°F, determine (a) the temperature at which the normal stress in the alumi-num bar will be equal to –11 ksi, (b) the corresponding exact length of the aluminum bar.
A 10-mm diameter steel bolt is surrounded by bronze sleeve. The outer diameter of the bronze sleeve is 20 mm and its inner diameter is 10-mm. Given that the yield stress for the steel is 640 MPa and the yield stress for the bronze is 520 MPa, determine the magnitude of the maximum allowable total load that can be applied to this assembly. (Assume full bond between the steel and the bronze sleeve) Esteel = 200 GPa, Ebronze = 100 GPa, Factor of safety = 1.5
PLS ANSWER ASAP TY! For the assembly shown, a yoke on a 30 mm diameter rod is attached to a 25 mm thick bracket via 15 mm diameter bolt as shown. The ultimate axial strength in the 30 mm dia. rod is 150 MPa. a)Determine the largest load P (in KN) that can be applied to the rod if a factor of safety of 2.5 with respect to the ultimate axial strength is required. b) What is the tensile axial stress on the rod (in MPa)? c) What is the shear stress on the bolt (in MPa)? d) What is the factor of safety for the 15 mm. dia. bolt with respect to the ultimate shear strength? (in 2 decimal places)
A short column is made by nailing two 1 * 4-in. planks to a 2 * 4-in. timber. Determine the largest compressive stress created in the col-umn by a 12-kip load applied as shown at the center of the top section of the timber if (a) the column is as described, (b) plank 1 is removed, (c) both planks are removed.