Two horizontal 5-kip forces are applied to pin B of the assembly shown. Knowing that a pin of 0.8-in. diameter is used at each connection, determine the maximum value of the average normal stress (a) in link AB, (b) in link BC. 05 in. 1.S in. 5 kips 5 kips 0,5 in. 60 1.8 in.

Two horizontal 5-kip forces are applied to pin B of the assembly shown. Knowing that a pin of 0.8-in. diameter is used at each connection, determine the maximum value of the average normal stress (a) in link AB, (b) in link BC. 05 in. 1.S in. 5 kips 5 kips 0,5 in. 60 1.8 in.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Two members of uniform cross section 50 *80 mm are glued together along plane a–a that forms an…

A: Draw the stress element of the cross-section.

Q: A 1-in. square (thickness 0.12-in) plate was subjected to a uniform load of 0.72 kip/in in the…

A: Givensquare platea=1int=0.12inFx=0.72 kip/inFy=1.44 kip/inE=29×106 psiv=0.3

Q: Portions of a 1/2 x 1/2 -in. square bar have been bent to form the two machine components shown.…

A: Given Data: The coss-sectional area of the squer bar is: 0.5 X 0.5 in2. The allowable stress is :…

Q: The vertical portion of the press shown consists of a rectangular tube having a wall thickness t5 10…

Q: The rigid castings A and B are connected by two 20 mm diameter steel bolts CD and GH and are in…

Q: PROBLEM 1.3 3 in. 30 kips Two solid cylindrical rods AB and BC are welded together at B and loaded…

Q: Two horizontal 9-kips forces are applied to pin B of the assembly shown. Knowing that a pin of…

Q: Straight rods of 0.30-in. diameter and 200-ft length are sometimes used to clear underground…

A: (a) The radius of the rod is given as, Moment of inertia is written as, The diameter of the spool…

Q: [2.37] The 1.5 m concrete post is reinforced with six steel bars, each with 28 mm diameter. Knowing…

Q: determine the largest load P t

Q: The boom AB is made up of a hollow square 100-mm tube having a wall thickness of 5 mm. A 10-mm…

A: Given data, Outer dimension of hollow boom AB is 100 mm and thickness is 5 mm. So, cross-sectional…

Q: Two loads are applied to the bracket BCD as shown. (a) Knowing that the control rod AB is to be made…

A: Moment about C = (?)(0.6) − (50 x 103)(0.3) − (15 x 103)(0.6) = 0…

Q: 17. Two horizontal 5-kip forces are applied to pin B of the assembly shown. Knowing that a pin of…

A: (17)Draw the free body diagram of pin B. Let consider the equilibrium condition Now consider the…

Q: Two horizontal 6.42-kip forces are applied to pin B of the assembly shown. Knowing that a pin of…

Q: Link BD consists of a single wooden member 38.2 mm wide and 20.4 mm thick. Knowing that each pin has…

Q: The steel tie bar shown is to be designed to carry a tension force of magnitude P = 130KN when…

Q: The ABC element is supported by a pin at C and a BD cable. Knowing that the limit load for the BD…

Q: An offset h must be introduced into a metal tube of 0.75-in. outer diameter and 0.08-in. wall…

Q: Link BD consists of a single wooden member 38 mm wide and 19.2 mm thick. Knowing that each pin has a…

A: Width of link BD, b= 38 mm Thickness of link BD, t= 19.2 mm Diameter of the pin, d= 14.30 mm θ= 0∘…

Q: Two gage marks are placed exactly 10 in. apart on a 1⁄2-in.-diameter aluminum rod with E = 10.1 x…

A: GivenL1=10inL2=10.009ind=0.5inE=10.1×106 psiσu=16ksi

Q: Three wooden planks are fastened together by a series of bolts to form a column. The diameter of…

A: Given data dblt=0.012 mσmax=36×106 psi

Q: Two hydraulic cylinders are used to control the position of the robotic arm ABC. Knowing that the…

A: a) Draw free body diagram of member ABC Force in rod AE can be determined as Stress in rod AE can…

Q: The vertical portion of the press shown consists of a rectangular tube having a wall thickness t5 10…

A: Given data: The thickness of the tube is t = 10 mm. The maximum load is P = 20 kN. The length of…

Q: Two horizontal 14.52-kip forces are applied to pin B of the assembly shown. Knowing that a pin of…

A: The bearing stress at A in member AB is 67488 psi.

Q: The elevation of the platform is controlled by two identical mechanisms, only one of which is shown.…

A: Load = 1500 lb Here we need to draw free body diagram and solve the sum So here I am drawing it in…

Q: Two horizontal 12.39-kip forces are applied to pin B of the assembly shown. Knowing that a pin of…

A: Given: P = 12.39 kip d = 0.8 inch t = 0.5 inch

Q: The steel pressure tank shown has a 750-mm inner diameter and a 9-mm wall thickness. Knowing that…

A: Given data The inner diameter of the tank is d=750 mm The wall thickness is t=9 mm The gauge…

Q: Two horizontal 5.92-kip forces are applied to pin B of the assembly shown. Knowing that a pin of…

A: P = 5.92 kip d = 0.82 inch t = 0.5 inch

Q: An 18-m-long steel wire of 5-mm diameter is to be used in the manu-facture of a prestressed concrete…

A: Given is: Length of steel wire, l=18m Diameter of the wire, d= 5mm = 0.005m Stretch or change in the…

Q: A vertical force P of magnitude 18 kips is applied at a Point C located on ti column. Knowing that y…

Q: 5. The load P applied to a steel rod is distributed to a timber support by an annular washer. The…

A: Given:stress in steel rod, σst=35 MPaDiameter of rod, dr=22 mmInner diameter of washer, di=25…

Q: 1. A steel plate 5 /16 in. thick is embedded in a horizontal concrete slab and is used to anchor a…

Q: Two gage marks are placed exactly 250 mm apart on a 12-mm-diameter aluminum rod with E5 73 GPa and…

A: Given: The initial distance between the gage marks is l=250 mm. The final distance between the gage…

Q: A block of 10-in. length and 1.8 3 1.6-in. cross section is to sup-port a centric compressive load…

A: length, L=10-in Sides of the block a=1.8 in, b=1.6 in normal stress = 18 ksi…

Q: Two wooden members of 80 *120-mm uniform rectangular cross section are joined by the simple glued…

A: Given Data: The centric load acting on the block is P. The cross-section of the rectangular block…

Q: In the structure shown, an 8-mm diameter pin is used at A, and 12- mm diameter pins are used at B…

A: Given data :- At A (d) = 8mm At B and D (d) =12 mm Shear stress = 100 Mpa Normal stress = 250 MPa…

Q: An annular washer distributes the load P applied to a steel rod to a timber support. The rod's…

A: Given Diameter of rod, D = 22 mm Inner diameter, di = 25 mm Normal stress = 35 MPa Find…

Q: An offset h must be introduced into a solid circular rod of diameter d. Knowing that the maximum…

A: Given data: Maximum eccentric load stress must not exceed 4 times the center load stress, σe = 4σc.…

Q: aluminum pipe must not stretch more than 0.05 in. when it is subjected to a tensile load. Knowing…

Q: PROBLEM 1.6 Two brass rods AB and BC, each of uniform diameter, will be brazed together at B to form…

A: Given data: L=100 mρ=8470 kg/m3 Need to determine the length of rod AB for which the maximum nominal…

Q: The steel tie bar shown is to be designed to carry a tension force of magnitudeP=120 kN when bolted…

A: a) Diameter of bolt Since bolt is in double shear , F1=12P=60 KN ⟌=F1A; 60π4d2…

Q: Two gage marks are placed exactly 250mm apart on a 12mm-diameter aluminum rod with E=73Gpa and an…

Q: PROBLEM 1.2 Two solid cylindrical rods AB and BC are welded together at B and loaded as shown.…

A: The diameter of the small shaft can be determined as shown below.

Q: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that the…

A: given:

Q: Two horizontal 9-kips forces are applied to pin B of the assembly shown. Knowing that a pin of…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked .…

Q: A glue-laminated column of 3-m effective length is to be made from boards of 24 x 100-mm cross…

Q: Two horizontal 4.3-kip forces are applied to pin Bof the assembly shown. Knowing that a pin of…

Q: B The steel tie bar shown is to be designed to carry a tension force of magnitude P = 120 kN when…

Q: of the assembly shown. Knowing that a pin of 20 mm diameter is used at each connection, determine 2…

Q: The four forces shown are applied to a rigid plate supported by a solid steel post of radius a.…

A: Given data: The value of force P is P=24 kips The value of radius a is a=1.6 in

Concept explainers

Forced undamped vibrations

In mechanical engineering, vibration is expressed as the term that occurs due to an object's backward and forward movement about a point of equilibrium. Generally, there are three types of vibrations which are,

Question

Two horizontal 5-kip forces are applied to pin B of the assembly shown. Knowing that a pin of
0.8-in. diameter is used at each connection, determine the maximum value of the average normal
stress (a) in link AB, (b) in link BC.
0.5 in.
1.S in.
5 kips
5 lips
0,5 in.
60
1.8 in.
Fig. P8.8

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

In the steel structure shown, a 6-mm-diameter pin is used at C and 12-mm-diameter pins are used at B and D. The ultimate shearing stress is 150 MPa at all connections, and the ultimate normal stress is 350 MPa in link BD. Knowing that a factor of safety of 3.0 is desired, determine the largest load P that can be applied at A. Note that link BD is not reinforced around the pin holes. The largest load P that can be applied at A is kN.
Two links BF are made of steel with a 450-MPa ultimate normal stress and has a 6x12–mm uniform rectangular cross section. Links BF are connected to members ABD and CDEF by 8-mm diameter pins; ABD and CDEF are connected together by a 10-mm diameter pin; CDEF is connected to the support by a 10-mm diameter pin; all of the pins are made of steel with a 170 MPa ultimate shearing stress. Knowing that a factor of safety of 3 is desired, determine the largest load P that may be applied
Each of the two vertical links CF connecting the two horizontal members AD and EG has a 10x40-mm uniform rectangular cross section and is made of a steel with an ultimate strength in tension of 400 MPa,while each of the pins at C and F has a 20-mm diameter and is made of a steel with an ultimate strength in shear of 150 MPa. Determine the overall factor of safety for the links CF and the pins connecting them to the horizontal members.
The ABC element is supported by a pin at C and a BD cable. Knowing that the limit load for the BD cable is 150 kN, and the coefficient Safety with respect to cable failure for BD of 3.5 determine the maximum value of the load P that can be supported. Determine the diameter of pin C, knowing that it is made of steel with an admissible stress of σadm = 270 Mpa, and that it is subjected to shear double.
A glue-laminated column of 3-m effective length is to be made from boards of 24 x 100-mm cross section. Knowing that for the grade of wood used, E= 11 GPa and the adjusted allowable stress for com-pression parallel to the grain is σC= 9 MPa, determine the number of boards that must be used to support the centric load shown when (a) P= 34 kN, (b) P= 17 kN
In the structure shown, an 8-mm-diameter pin is used at A and 12 mmdiameter pins are used at B and D. Knowing that the ultimate shearingstress is 100 MPa at all connections and the ultimate normal stress is 250 MPa in each of the two links joining B and D, determine the allowable load P if an overall factor of safety of 3.0 is desired.
In the structure shown, an 8-mm-diameter pin is used at A, and 12-mm-diameter pins are used at B and D. Knowing that the ultimate shearing stress is 100 MPa at all connections and that the ultimate normal stress is 250 MPa in each of the two links joining B and D, determine the allowable load P if an overall factor of safety of 2.6 is desired.
Determine the largest axial load P that can be safely supported by a flat steel bar consisting of two portions, both 10 mm thick and, respectively, 40 and 80 mm wide, connected by fillets of radius r=4 mm. Assume an allowable normal stress of 180 MPa.
A 2-m length of an aluminum pipe of 240-mm outer diameter and 10-mm wall thickness is used as a short column to carry a 640-kN centric axial load. Knowing that E= 73 GPa and ν=0.33, determine (a) the change in length of the pipe, (b) the change in its outer diam-eter, (c) the change in its wall thickness
In the structure shown, an 8-mm diameter pin is used at A, and 12- mm diameter pins are used at B and D. Knowing that the ultimate shearing stresses is 100 MPa at all connections and that the ultimate normal stress is 250 MPa in each of the two links joining B and D, determine the allowable load P if an overall factor of safety of 3.0 is desired.
A rectangular cross section steel column of length L, a fixed end at B and supports a concentric load at A as shown. Point A is restrained from moving in one of the vertical planes of symmetry of the column, but allows to move in the other plane by the use of two smooth and rounded fixed plates.(a) Determine the ratio a/b of the two sides of the cross section corresponding to the most efficient design against buckling.(b) Design the most efficient cross section for the column, knowing that L = 45 in., E = 10 x 106 psi, P = 20 kips, and that a factor of safety of 2.7 is required. Answers: (a) _______ (b) _______
Each of the five struts shown consists of a solid steel rod. (a) Know-ing that strut (1) is of a 0.8-in. diameter, determine the factor of safety with respect to buckling for the loading shown. (b) Determine the diameter of each of the other struts for which the factor of safety is the same as the factor of safety obtained in part a. Use E=29 *106 psi