P12.20 The cylinder in Figure P12.20 consists of spirally wrapped steel plates that are welded at theseams. The cylinder has an outside diameter of 280 mm and a wall thickness of 7 mm. The cylinder issubjected to axial loads of P = 90 kN. For a seam angle of ẞ= 35°, determine:(a) the normal stress perpendicular to the weld seams.(b) the shear stress parallel to the weld seams.P

A.Step 1:First, determine the cylinder's circumference. The circumference may be computed with the…

Answered: P12.20 The cylinder in Figure P12.20…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the cracking moment in kN-m for the section shown if: f'c = 28MPa fr=(0.7)
Determine the cracking moment in kN-m for the section shown if: f'c = 28MPa fr=0.7(square root of (f')(c))
The copper pipe has an outer diameter of 40 mm and an inner diameter of 37 mm. If it is tightly secured to the wall at A and three torques are applied to it as shown, determine the maximum shear stress developed in the pipe. Let T1=66, T2 =11, T3 =26
The shaft is made from a solid steel section AB and a tubular portion made of steel having a brass core. It is fixed at a rigid support at A and a torque T=50lb-ft is applied at C. Gsteel= 11,500 ksi Gbrass= 5,600 ksi What is the angle of twist at C? What is the maximum shear stress in the steel and brass? What is the maximum shear strain in the steel and brass?
2.2 The hydraulic cylinder CF, which partially controls the position of rod DE, has been locked in the position shown. Member BD is 5/8 in. thick and is connected to the vertical rod by a 3/8-in.-diameter bolt. Determine (a) the average shearing stress in the bolt, (b) the bearing stress at C in member BD.
To determine the state of stress in a solid rod using the principle of superposition. A solid rod has a diameter of e = 50 mm and is subjected to the loading shown. Let a = 190 mm, b= 220 mm, c = 310 mm, d = 220 mm, and P = 3.0 kN. Take point A to be at the top of the circular cross-section. (Figure 1) Figure < 1 of 2 ▼ ▼ Part A - Moment about the x axis at A M₂ = As shown (Figure 2), a cut was made at A to determine the resultant internal loadings. Determine the moment about the x axis, M, Express your answer to three significant figures and include the appropriate units
An aluminum alloy pipe AB [EAB = 12,000 ksi]with a cross-sectional area of AAB = 6.40 in.2 isconnected at flange B to a steel pipe [EBC =50,000 ksi] with a cross-sectional area of ABC= 7.60 in.2. The assembly is connected to rigidsupports at A and C.[LAB = 86 in.; LBC = 146 in.; PB = 177 kips ⇾]Determine the normal stresses in aluminumpipe AB and steel pipe BC.
The pipe shown, has an inner diameter of 80mm and an outer diameter of 100mm. If its end is tightened against the support at A using a torque wrench at B, determine the shear stress developed in the material at the inner and outer walls along the central portion of the pipe when the P (in newtons) forces are applied to wrench. P=74 Show detailed solution
The long bolt passes through the 30-mm-thick plate. If the force in the bolt shank is 9 kN, determine the magnitudes of the average normal stress in the shank, the average shear stress along the cylindrical area of the plate defined by the section lines a–a,and the average shear stress in the bolt head along the cylindrical area defined by the section lines b–b. Answers should be in MPa.
Find the deformation of the bar in the figureE= 200gpa
Two forces P1 and P2, of magnitude P1 = 15 kN and P2 = 18 kN, are applied as shown to the end A of bar AB, which is welded to a cylindrical member BD of radius c= 20 mm. Knowing that the distance from A to the axis of member BD is a= 50 mm and assuming that all stresses remain below the proportional limit of the material, determine the following: 1. What is the absolute value of the axial stress at point K of the transverse section of member BD located at a distance b = 60 mm from end B in MPa. 2. What is the flexural stress at point K of the transverse section of member BD located at a distance b = 60 mm from end Bin MPa. 3. What is the total normal stress at point K of the transverse section of member BD located at a distance b = 60 mm from end B in MPa.
The compound shaft consists of bronze and steel segments, both having 120-mm diameters. If the torque T causes a maximum shear stress of 100 MPa in the bronze segment, determine the angle of rotation (in degrees) of the free end. Use G = 83 GPa for steel and G = 35 GPa for bronze.

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS