P5.94. A delta-connected source delivers power to a delta-connected load, as shown in Figure P5.94. The rms line-to-line voltage at the source is Vabrms =440 V. The load impedance is ZA = 12 + j3. Find InA, VAB, IAB, the total power delivered to the load, and the power lost in the line. %D 1Ω +2Ω Vm [30° 12 +j2 2 ZA a B Vm/-90° Vm /150° 12 +j2 2 Figure P5.94

P5.94. A delta-connected source delivers power to a delta-connected load, as shown in Figure P5.94. The rms line-to-line voltage at the source is Vabrms =440 V. The load impedance is ZA = 12 + j3. Find InA, VAB, IAB, the total power delivered to the load, and the power lost in the line. %D 1Ω +2Ω Vm [30° 12 +j2 2 ZA a B Vm/-90° Vm /150° 12 +j2 2 Figure P5.94

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.18P: Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of...

See similar textbooks

Similar questions

Two loads, A and B, are connected in parallel across a 1-kV-rms 60-Hz line, as shown in Figure P5.81. Load A consumes 10 kW with a 90 percent lagging power factor. Load B has an apparent power of 15 kVA with an 80 percent lagging power factor. Find the power, reactive power, and apparent power delivered by the source. What is the power factor seen by the source? Repeat Problem P5.81 if load A consumes 5 kW with a 90 percent lagging power factor and load B consumes 10 kW with an 80 percent leading power factor.
In U.S. residences, electrical power is generally utilized at a nominal voltage of 120 V rms. What problems would become pronounced if the power distribution system and household appliances had been designed for a lower voltage (say, 12 V rms)? For a higher voltage (say, 12 kV)?
Find the rms value of the current waveform shown in Figure P5.13.
Assuming that a nonzero ac voltage source is applied, what can you say about whether the power and reactive power are positive, negative, or zero for a pure capacitance in series with a pure inductance? Consider cases in which the impedance magnitude of the capacitance is greater than, equal to, or less than the impedance magnitude of the inductance. Repeat Problem P5.74 for the inductance and capacitance in parallel.
Two loads, A and B, are connected in parallel across a 1-kV-rms 60-Hz line, as shown in Figure P5.81. Load A consumes 10 kW with a 90 percent lagging power factor. Load B has an apparent power of 15 kVA with an 80 percent lagging power factor. Find the power, reactive power, and apparent power delivered by the source. What is the power factor seen by the source?
Find the phasors for the current and for the voltages of the circuit shown in FigureP5.41. Construct a phasor diagram showing and What is the phase relationshipbetween and I?
Find the total impedance, voltage drop on the 100-ohm resistor, draw the phasor diagram of the voltage and current at R1, total power (apparent) delivered by the current source, draw the phasor diagram of the voltage and current at the source. Also, is the circuit inductive, capacitive, or neither (resistive)? please give the step-by-step solution NOTE: Polar form for Voltage & Current. Rectangular form for Impedance
For the maximum average power transfer in the circuit shown in Figure 2, use the impedance ??.and ??Find the value of the maximum average power transferred to ? (Can you write the steps in detail in sentences?)
Describe the concept of load flow analysis in power systems. How is it used to determine the steady-state operating conditions of a network?
Assuming that a nonzero ac voltage source is applied, what can you say about whether the power and reactive power are positive, negative, or zero for a pure capacitance in series with a pure inductance? Consider cases in which the impedance magnitude of the capacitance is greater than, equal to, or less than the impedance magnitude of the inductance.
Discuss the importance of reactive power in power systems. How is it controlled, and what are the consequences of poor reactive power management?
For maximum average power transfer in the circuit shown in the figure, set the impedance ZLand ZLFind the value of the maximum average power transferred to ? (Can you write the steps in detail in sentences?)