Answered: +j50 N ) 2/0° 100 2 Figure P5.89

Engineering

Electrical Engineering

+j50 N ) 2/0° 100 2 Figure P5.89

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.1MCQ: The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax

See similar textbooks

Related questions

Q: Consider the phasors shown in Figure P5.22. The frequency of each signal is f=200 Hz. Write a…

A: Frequency is given f = 200 Hz. Angular frequency is given by,

Q: QI: Draw the impedance diagram for the series R-C circuit for the figure, then find the : Q2: For…

Q: Two loads, A and B, are connected in parallel across a 1-kV-rms 60-Hz line, as shown in Figure…

A: For load active power is given, Power factor is given, Therefore, apparent power is, Reactive…

Q: *P5.33. A voltage vL(t) = 10 cos(2000rt) is applied to a 100-mH inductance. Find the complex…

Q: Consider the circuit shown in Figure P5.79. Find the phasor current I. Find the power, reactive…

A: Calculating reactance of the inductor Calculating equivalent impedance

Q: P5.28. Reduce 5 sin(wt) + 5 cos(wt + 30°) + 5 cos(wt + 150°) to the form Vm cos(wt + 0).

A: Answer:- Zero.

Q: Consider the situation shown in Figure P5.85. A 1000-V-rms source delivers power to a load. The load…

A: (a) When capacitor is not connected, to calculate the RMS value of current we will use the actual…

Q: A 60-Hz 240-V-rms source supplies power to a load consisting of a resistance in series with an…

A: Given data, Frequency f = 60 Hz Voltage V = 240 V Real power P = 1500 W Apparent power S = 2500 VA

Q: b. Q =-3KVAR ,P = 5kW %3D Determine the Complex Power, Apparent Power, Current, Voltage and Power…

A: (b) It is given that: Q=-3 KVArP=5 KW

Q: P5.7. Find the phasors for the current and for the volta in Figure P5.7. Construct a phasor diagram…

A: Given vst=10cos500t V In phasor form, Vs=10∠0° V and ω=500 rad/s Apply KVL, we get Vs=VR+VL=IR+IXL…

Q: The impedance ZL in the circuit is adjusted for maximum average power transfer to ZL. The internal…

Q: The load impedance ZL for the circuit shown is adjusted until maximum average power is delivered to…

A: (A) The maximum average power to the load ZL, when ZL is adjustable is: Where, The magnitude of the…

Q: Consider the circuit shown in P5.50Figure . Find the phasors Vs, I, VL, VR and VC.Compare the peak…

A: Given data: Vs(t) is: 10 cos(104t) R is: 100 Ω The source voltage is given as, vs(t) = 10…

Q: The Thévenin equivalent of a two-terminal network is shown in Figure P5.93. The frequency is f=60…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: 100 N UR v,(t) = 10 cos(500r) 0.2 H Figure P5.41

Q: ZL impedance for maximum average power transfer in the circuit shown in Figure 2 and find the value…

Q: *P5.97. A balanced wye-connected three-phase source has line-to-neutral voltages of 440 V rms. Find…

A: In this question, A 3 phase star balanced sources is supplied to the 3 phase balanced star load.…

Q: Find the phasors for the current and the voltages for the circuit shown in Figure P5.40. Construct a…

A: To find the current in the circuit and voltage across resistor and capacitor. Draw the phasor…

Q: Find the following in rectangular form: a. What is the real power delivered by the source (in W)? b.…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: Discuss the following term in reactive circuit? a) Real power b) Apparent power G) Power factor 1.

Q: P5.63. Consider the circuit shown in Figure P5.63. Find the phasor current I. Find the power,…

A: Ac sinusoidal analysis Given Inductor value = 1H

Q: Find the phasors for the current and the voltages for the circuit shown in Figure P5.45. Construct a…

A: Here, reactance offered by capaciton is, Vc = 1jwc Vc=1j500×2×10-6Ω…

Q: A balanced wye-connected three-phase source has line-to-neutral voltages of 240 V rms. Find the rms…

A: Given data, The value of phase rms voltage VPrms = 240 V. The value of resistance R1 = 10 Ω The…

Q: Two loads, A and B, are connected in parallel across a 1-kV-rms 60-Hz line, as shown in Figure…

A: Given data: Real Power of load A, PA = 10 kW Power factor of load A, cosφA = 0.9 Apparent Power of…

Q: Find the phasors for the voltage and the currents for the circuit shown in Figure P5.48. Construct a…

A: Given data: is=0.1cos104tIs=0.1∠0°ω=104R=100 Ω

Q: (a). Write the instantaneous currents across the three circuit elements in terms of Vm amp > angular…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: The circuit shown in Figure having resistor 200N and a capacitor 50 µF is connected to a 230 V, 50…

Q: P5.17. Find the rms value of the voltage waveform shown in Figure P5.17 D. V(1) T= 2 Figure P5.17

Q: What are the customary units for real power? For reactive power? For apparent power?

A: Given: To describe the customary units for real power is shown as:

Q: Find the rms value of the current waveform shown in Figure P5.13.

A: Given data: T=4 The expression for the rms value of the current is given as, Irms=1T∫0Ti2tdt

Q: Q5/B: Explain delta-star connection of 3 ph transformers. What its advantages and disadvantages?

A: ∆-Y connection of 3-phase transformer: In a three-phase transformer with a delta-star connection,…

Q: Q2. A series of motor (Load 1) and lighting (load 2) are connected to an AC source as show in Figure…

Q: Find the rms value of the voltage waveform shown in Figure P5.17.

A: The function is expressed as: vt=5t2 0<t≤2 The rms value is given as: vrms=1T∫0Tvt2dt

Q: To attain maximum power delivered to a load, what value of load impedance is required if a. the load…

A: a) Given that, The load impedance is any complex value Let assume that thevenin impedance is Ze =…

Q: A balanced wye-connected three-phase source has line-to-neutral voltages of 440 V rms. Find the rms…

A: Given data, The value of line-to-neutral rms voltage is VPrms = 440 V. The value of resistance is R…

Q: Find the phasors for the voltage and the currents of the circuit shown in Figure P5.47. Construct a…

A: The reactance offered by the inductor is: Where, The angular frequency of the supply is “ω” which…

Q: Assuming that a nonzero ac voltage source is applied, what can you say about whether the power and…

A: Draw the circuit diagram for a series connection of the inductor and the capacitor.

Q: Consider the circuit shown in Figure P5.79. Find the phasor current I. Find the power, reactive…

A: To find the value of current I the circuit can be modified as The value of Z is given as Thus…

Q: P5.26. Write an expression for the sinusoid shown in Figure P5.26 O of the form v(t) = Vm cos(wt +…

Q: *P5.33. A voltage VL(t)=10 cos(2000TTt) is applied to a 100-mH inductance. Find the complex…

A: Key Points Let voltage across the inductance is taken as a reference then current in the inductor…

Q: When the average real power absorbed by an impedance is zero, then the impedance is: Select one: a.…

Q: P5.43. Compute the complex impedance of the net- work shown in Figure P5.43 for w = 500. 1000 and o…

Q: Figure P5.12

A: Using KVL at positive terminal of op amp Here vn is the voltage at negative terminal

Q: P5.94. A delta-connected source delivers power to a delta-connected load, as shown in Figure P5.94.…

Q: *P5.21. Suppose that v1 (t) = 100 cos (wt) and v2(t) = 100 sin(wt). Use phasors to reduce the sum v,…

A: In this question we have to find the sum of phasors v1(t) +v2(t) and also draw the phasor diagram

Q: Find the total impedance of the circuit, total power (apparent) delivered by the current source,…

Q: Find the total impedance, voltage drop on the 100-ohm resistor, draw the phasor diagram of the…

A: Current and voltage always in phase incase of resistance Current lag by 90 degree with respect to…

Q: Determine the capacitance value that, when placed in parallel with this load, would produce a unity…

A: Given Voltage V=230 V Frequency f=60 Hz When capacitance is placed in parallel with the load which…

Concept explainers

Norton Theorem

In the current circuit law, the Norton theorem (also known as the Mayer-Norton theorem) is a simplification that can be applied to networks generated by a constant line of opposition, power sources, and current assets. In two network terminals, it can be switched on with a current supply and single resistor respectively.

Question

a. Find the Thévenin and Norton equivalent circuits for the circuit shown in Figure P5.89.
b. Find the maximum power that this circuit can deliver to a load if the load can have any complex impedance. c. Repeat if the load is purely resistive.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Shown below is the voltage waveform applied to a pure capacitor of 100 uF. Solve for the RMS value and the average value of the voltage waveform. Choices for RMS value: A) 14.142 V B) 6.366 V C) 12.732 V D) 11.547 V Choices for average value: A) 5 V B) 20 V C) 10 V D) 12 V
The current in a pure capacitor circuit is i=0.17cos500t. If the rms value of the impressed emf is 80 volts. a) What are the equation for the voltage and power? b) What is the circuit frequency?
The power factor angle of a purely inductive circuit is 0 degrees Select one: True False
Given below are Za=Zb=Zc=(25+j5) Ω : Calculate the total average, reactive and complex powers?
13 ) RMS value of sinusoidal voltage is given by Vrms= 5 V, Calculate the value of peak voltage Vm? a. 1.4142 V b. 5 V c. 3.535 V d. 7.07 V
Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
The average value of a double-frequency sinusoid, sin2(t+), is given by (a) 1 (b) (c) Zero
Answers: a. 150 Vb. 106.066 Vc. 20 msd. 50 Hze. 200 Vf. 141.4214 Vg. 13.3333 msh. 75 Hz
An rms voltage of 22.2 V with a frequencyof 1.00 kHz is applied to a 0.290-mH inductor. (a) What is the rmscurrent in this circuit? (b) By what factor does the current changeif the frequency of the voltage is doubled? (c) Calculate the current for a frequency of 2.00 kHz
Calculate the rms value of a sinusoidal current of maximum value 20A.
Compute the reactive power for -j25Ω with a voltage source, Vg = 240∠0⁰ (rms) NOTE: EXPRESS YOUR ANSWER IN POLAR FORM