PART 3 1. Connect the circuit of Figure (2), the output of the power supply (20). 2. Slowly increase the supply voltage until E=20V , this voltage must remain constant, change the load resistance and record Vi, li, Iz, Rz, in table (3). 6802 100-10KO 20 V Figure (2) 5 ELECTRONIC LAB. EXP 6 LECTURER: MUSTAFA Y.AL-NAELI E(v) RL(Q) VL (v) L (mA) Iz (mA) 200 400 600 800 1K 20 1.5 K 2 K 4K 6 K 8 K 10 K

PART 3 1. Connect the circuit of Figure (2), the output of the power supply (20). 2. Slowly increase the supply voltage until E=20V , this voltage must remain constant, change the load resistance and record Vi, li, Iz, Rz, in table (3). 6802 100-10KO 20 V Figure (2) 5 ELECTRONIC LAB. EXP 6 LECTURER: MUSTAFA Y.AL-NAELI E(v) RL(Q) VL (v) L (mA) Iz (mA) 200 400 600 800 1K 20 1.5 K 2 K 4K 6 K 8 K 10 K

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter6: Reading Schematic Diagrams

Section: Chapter Questions

Problem 4RQ: Schematic diagrams break the wiring of control systems down into a(n) _____ arrangement. a....

See similar textbooks

Similar questions

Question lets assume:Vd=300V, D=0.5 I0=30A fs=100kHz Vswitch drop =0.0V And the figure 1 below has a extra magnetizing winding. (i) Calculate the rated output power and equivalent load resistance. (ii) If IL=IL,max –IL,min is equal to 0.2A. Calculate L, when VL=V0 (iii) Sketch the current and voltage waveform of an inductance for the converter circuit shown in figure (1)
D-MOSFET: lVtl= 2 V, Idss =10 mA, Is=1.6 mA, rd=14 K, RL=2 K. Calculate the dc drain-to-source voltage. Please write your answer as a V and don’t use units in the answer. Please use one digit after the dot.
Design a 24v zener regulated power supply circuit that will power a 500 ohms load with 1A of current.
4.a. A demountable stud bushing on high-voltage leads eliminates the need fora. an oil stop.b. a gasket.c. a terminal lug. 4.a. A power transformer with standard insulation class of 69 kv will withstand an rms test voltage ofA. 140 kv.B. 440 kv.c. 69kv.
Suppose that the voltage source has an internal series resistance of 50 Ω. How would the outputvoltage be affected (assuming that R1 and R2 are the same as you specified earlier)? Work out your resultsfor both the ideal voltage source and for the voltage source with the internal impedance. R1 and R2 are both 3 Ohms and Vin = 10 V
What are the main attributes of high quality power?
Variation of which of the following parameter is not consider as power quality problem for industry?VoltageCurrentPowerFrequency
In the Zener circuit shown below, calculate the Zener current IZ when VZ=10 V, E=14 V, R1=298 ohm, and R2 =298 ohm.
For the following circuit, calculate the following:a) Obtain the DC load line of the circuit and locate the operating point. What is the area of operation?b) Calculate the voltage gain.c) Calculate the input impedance.d) If Vs has an alternating voltage of 0.5mV, calculate the output voltage and draw on the same graph, both the input and output voltage. β= 110 Rx= 4KΩ
What is curent
What is the difference between active and passive loads
If V1 = ± 21V, R = 19,8kΩ, RL = 11,6 and zener voltage 3,3 in the circuit above What V will be the peak point of the voltage falling on the resistor R in the positive alternation of V1?