Help me solve this question ASAP !! c) Figure 3 shows,the piston rod of a double acting cylinder 1 is to extend, when three ofnormally open pushbuttons (PB1 AND PB2 AND PB3) are actuated and will only retractwhen the fully extend position of a double acting cylinder is reached, which detected by anormally open Roller Limit switch (RLSW1) AND, after 20 seconds extension of fullyextension of cylinder.Cylinder 1RLSW 1Figure 3Hint : 5/2 way double solenoid valve should be usedi) Give all the component to be usedii) Sketch an electro pneumatic circuit diagram to solve the aboveproblem label all the port designations.iii) Explain the circuit operation

Rundown of parts utilized. 1. Twofold acting inder-No's 2. Pilot worked DCV ( Directional control…

Answered: piston rod

Engineering

Mechanical Engineering

piston rod

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A swivel bridge is bought into the desired position by means of a double–acting cylinder. The piston rod of a double–acting cylinder is to extend when a push button switch is actuated. The cylinder is to remain extended until a second switch is actuated and only if the first switch has been released. The cylinder is to then return to the initial position. The cylinder is to remain in the initial position until a new start signal is given. The speed of the cylinder is to be adjustable in both directions of travel. a) Draw the pneumatic and electro-pneumatic circuits of the system
The piston rod of a double-acting cylinder is to advance when a 3/2- way push button valve is actuated manually. The cylinder is to remain advanced until a second valve is actuated. The signal of the second valve can only take effect after the first valve has been released. The cylinder is to then return to the initial position. The cylinder is to remain in the initial position until a new start signal is given. The speed of the cylinder is to be adjustable in both directions.Draw the circuit diagram for the problem.
Q#04 (a) :What is Mechanism Design ? (b): Explain the Importance of Time Ratio and Timing charts in Mechanism design in detail.
In relation to the circuit presented below, mark the alternative(s) that you consider correct. 1 To enable actuator A2 to advance, it is necessary to switch valve V2 to the leftmost position and ensure that valve V1 is in its initial (intermediate) position. 2 Switching valve V2 to the leftmost position allows actuator A2 to advance, but for this to happen, valve V1 must also be switched to the leftmost position. 3 When activating valve V1, using the locking lever installed on the left side of it, the two actuators (A1 and A2) are allowed to advance. 4 Hydraulic pump B1 is a simple variable displacement type. 5 Valves V1 and V2 have a TANDEM center.
question:1Explain the Importance of Time Ratio and Timing charts in Mechanism design in detail.
Block diagram and explanation of the applications of open loop system: Automatic washing machine, Automatic toaster system, Traffic light controller and Furnace without thermostatic control but with timing device
Identify the number of instantaneous centres present in a mechanism which has 4 links. a. 18 b. 12 c. 10 d. 6
What is the minimum mobility of a mechanism?and mobility of a three link kinematic locked chain?
What are the possible sources of errors and their effect on the calculated paramaters?
diffrenece between the Pure mechanism from Constructive mechanism. indicate the schematic diagram
Explain a brief introduction to the angular transmitter mechanism and its application ?
- Industrial Motor Controls, 12.a. What is the purpose of thermostat number 2, IN7, in the mixing vat machine?A. This thermostat is used to monitor the temperature of the incoming fluids.B. This thermostat is used to prevent an over-temperature condition in the event thermostat one sticks open.C. This thermostat is used to turn off the mixing motor after the mixture reaches temperature.D. This thermostat is used to shut off the heater when the chemical mix reaches setpoint.12.b. Why are motor current readings from a frequency inverter not exact readings of motor current?A. Because the output of a frequency inverter is not a sinewaveB. Because a frequency inverter adds a DC voltage level to the AC waveformC. Because a frequency inverter uses a lower voltage sinewaveD. Because the inverter pulses the motor with various sinewave frequencies