Ed, Edd and Eddy love to play on a seesaw. It consists of a 1-kg board with a length of 8 meters. One day, the other end broke down. They had to cut it by a meter and maintain the pin support in its original position. Then, they tried the seesaw altogether. Ed (m = 55kg) sat on one side about 3m from the pin while Edd (m = 40kg) and Eddy (m = 40kg) on the other side. If Edd was about 3m as well from the pin, calculate the following: The manitude of the reaction force (N) exerted by the pin support on the board. Assume Eddy is in between Ed and Edd. (mass of board = 1kg) Ans. 1332.8

Ed, Edd and Eddy love to play on a seesaw. It consists of a 1-kg board with a length of 8 meters. One day, the other end broke down. They had to cut it by a meter and maintain the pin support in its original position. Then, they tried the seesaw altogether. Ed (m = 55kg) sat on one side about 3m from the pin while Edd (m = 40kg) and Eddy (m = 40kg) on the other side. If Edd was about 3m as well from the pin, calculate the following: The manitude of the reaction force (N) exerted by the pin support on the board. Assume Eddy is in between Ed and Edd. (mass of board = 1kg) Ans. 1332.8

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.12P: A differential equation encountered in the vibration of beams is d4ydx4=2D where x = distance...

See similar textbooks

Similar questions

1. A non-uniform is 4.5m long and weighs 640N. It is balance when a 270N weight is hung 0.800m from the light end of the bar and the bar is pivoted at its center. Where is the center of gravity of the bar? 2.Two workers carry a non-uniform beam weighing 730N. The beam is 2.6m long and its center of gravity is 1.1 m from one end. If the workers hold the beam at its end, how much does each worker lift?
A hydraulic press has a ram of 30 cm diameter and a plunger of 2cm diameter. it is used for lifting a weight of 30 kN. How much force is required at the plunger? a) 155.5kN b)466.6kN c) 311.1 kN d) 233.3 kN
In a hydraulic press machine the diameters of the effort and load pistons are respectively 25 cm and 100 cm. Find the distance moved by the load piston if 10 strokes are applied to the effort piston . Given : Stroke length of the effort piston is : 50 cm . Distance moved by Load piston : ____________m
Chemistry The contact angle for water in a clean glass is zero. Calculate the surface tension of waterin a 0.3 mm diameter vertical tube if the water rises to a height 4.96 cm above the liquidoutside the tube, knowing that specific gravity of water equals 998.2 kg/m 3 and theacceleration due to gravity equals 9.806 m/sec2
The blood pressure in your heart is 1.52 x104 Pa. If an artery in the brain is 0.421 m above the heart, what is the pressure in the artery?
A tank, shaped like a cone has height 8 meters and base radius 3 meters long. It is placed so that the circular part is upward. It is full of water, and we have to pump it all out by a pipe that is always leveled at the surface of the water. Assume that a cubic meter of water weighs 10000 N, i.e. the density of water is 10000 N/m3. How much work does it require to pump all water out of the tank? Enter the exact value of your answer.
A hydraulic jack is used to raise a 10KN car. A force of 400N applied on a 25mm diameter jack plunger. What diameter of jack in mm is required to raise the car?
During a bicep curl on a bicep curl machine, I'm curling a weight stack of 100 pounds (single arm...I'm jacked like that). At this very moment, the weight stack has a moment arm of 0.12m, my elbow has an angle of 63deg, my muscle force vector has an angle of 23deg, and it attaches 3cm below my elbow joint on my radius. How much force must my bicep create right at this moment to hold the weight stack in place?
A submarine is traveling at a depth of ‘95’ kilometers in the ocean, where the gagepressure is 840 Kg(f)/cm2 . The density and bulk modulus of elasticity of water at the top surface of the ocean are 1025 kg/m3 and 24000 kg(f)/cm2 respectively. Find the following:(i) What will be the density of water at the depth of 2.0 kilometers?(ii) What will be specific volume and change of volume at that depth?(iii) What is the pressure at the top surface of the submarine? How much will bechanged in pressure if submarine change direction from North to East?
A wooden plank x meters long has one end leaning on top of a vertical wall 1.5 m long and the other end resting on a horizontal ground. Neglecting friction, find x if a force (parallel on the plank) of 100 N is needed to pull a 400 N block up the plank.
Ra=102lb, Ma=1020 ft*lb, Rc=Rd=199lb
A metal conduit will be used as a pathway for wiring through a concrete block. The conduit is a 4-foot-long rod with an outer diameter of 2.4 inches and an inner diameter of 2.2 inches. What is the volume of metal in the conduit in cubic centimeters? A copper pipe, used for plumbing from the water main to a house, is 4 meters long and has a circular cross-section 2.8 cm in diameter. There is a 2 cm diameter hole in the center of the cross-section for the entire length of the rod. What is the volume of copper in the rod in cubic inches? The density of copper is 559 lbm/ft3 . What is the mass of the copper pipe in pounds?