Please answer the following: 1. A balanced star connected load has an impedance of 6 + j8 ohms per phase connected to a balanced 3-phase 200 volts per phase. Determine: a) current per phase b) line currents c) power per phase d) total power e) reactive power per phase f) total reactive power g)total apparent power 200

Please answer the following: 1. A balanced star connected load has an impedance of 6 + j8 ohms per phase connected to a balanced 3-phase 200 volts per phase. Determine: a) current per phase b) line currents c) power per phase d) total power e) reactive power per phase f) total reactive power g)total apparent power 200

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.45P: Two balanced Y-connected loads, one drawing 10 kW at 0.8 power factor lagging and the other IS kW at...

See similar textbooks

Similar questions

For the circuit element of Problem 2.3, calculate (a) the instantaneous power absorbed, (b) the real power (state whether it is delivered or absorbed). (c) the reactive power (state whether delivered or absorbed). (d) the power factor (state whether lagging or leading). [Note: By convention the power factor cos() is positive. If | | is greater than 90, then the reference direction for current may be reversed, resulting in a positive value of cos() ].
in a balanced, 3 phase, positive sequence, grounded neutral source, supplies power to a balanced DELTA connected load. with the following conditions: Ibc = 9.0 cis 237 degrees amps; and true power per phase is = 343 watts, with 0.55 power factor lagging What is the value of the reactance per phase of the delta load in ohms? (Place negative sign for capacitive reactance.) ANSWER QUICKLY
The power system insulation problem involves a. Capacitance of earth and subsequent grounding b. Selection of basic insulation level of system equipment c. Determination of single phase line insulation d. Determination of three phase line insulation Clear my choice
A balanced Star connected load operates at a voltage of 460V , 0.8 Power factor lagging and each phase takes a power of 8KW. Consider it as 3 - phase 3 - wire system Calculate the total impedance . Calculate the value of Resistance and Inductive Reactance per phase .
A three-phase, four-wire, wye-connected system supplies a noninductive lighting load only. The current in line A is 8 A, in line B the current is 10 A, and in line C the current is 6 A. The voltage from each line wire to the neutral wire is 120 V. Determine: the power, in watts, indicated by each of the three wattmeters. the total power, in watts, taken by the entire lighting load
2. Solve the following problem: A THREE-PHASE PLANT CONSUMES 600 KVA, WITH A VOLTAGE OF 2400 VOLTS AND A POWER FACTOR OF 0.8 BEHIND. a) DETERMINE THE EQUIVALENT DELTA IMPEDANCE OF THE PLANT. b) IF THE PLANT WERE A STAR, CALCULATE THE RESISTANCE, REACTANCE AND THE CORRESPONDING PASSIVE ELEMENT.
A minimum of three wattemer should be used to measure power for a three phase balanced system. True False
Let the three-phase electrical system be illustrated in Figure . Knowing that its phase sequence is ABC and that Vcb=380∠135°V, determine the following: a) The value of the line currents demanded by each of the loads and supplied by the source. b) The power and power factor of each load and source. c) The power of the capacitor bank that must be installed to correct the power factor to 0.95 lagging. d) The currents supplied by the source after installing the capacitor bank. e) The percentage reduction of the total apparent power supplied by the source after installing the capacitor bank.
This wind farm needs a 250 km connection laid to Sommerville. The choice is either a 3 phase system or a bipolar dc system at 400 kV and ±400 kV at the receiving end respectively. (i) The 3-phase system has resistive losses per phase of 0.1 Ω/km. Calculate the system losses (in watts) when delivering 0.8 GW. (ii) The bipolar dc system has resistive losses of 0.1 Ω/km. Calculate the system losses (in watts) when delivering 0.8 GW. (iii) Calculate the efficiencies of the two systems. (iv) Comment on which system you would choose to use and why.
A balanced, three-phase, positive sequence, with grounded neutral source, supplies power to a balanced delta connected load. For the system, additional information are as follows: Vbn = 214 cis 185 degrees volts; and Ica = 7.9 cis138 degrees amperes What is the angle of the total apparent power in degrees? (Place negative sign for capacitive reactive power.)
a. Must you see two wattmeters to measure the total three-phase power on a balancedthree-phase three-wire system? Explain.b. Can a wattmeter that has a current through its current coil and a potential across itsvoltage coil, indicate zero? Explain.
2.1 Two power stations, A and B, are synchronized at 66 kV. They are inter-connected by a transmission line with an inductive reactance of 6.7-Ω and resistance of 3.5-Ω per phase. The voltage of power station A is advanced with an angle of 10.5 degrees with respect to the voltage of power station B. The loading of power station B has a real power of 200 MW. The respective loads of the two power stations are as follows: Power station A: 165 MVA at a power factor of 0.819 lagging. Power station B: The reactive power consumed by the load is 155 Mvar. *Round off to two decimal places to every question 15.The active power loss within the interconnector (MW). 16.The reactive power loss within the interconnector (MVar). 17.The final loading of power station A (MVA) and it's angle