Please select the correct answers according to the given figure for the elastic behaviour of steel and aluminium I. The elastic modulus of steel is about three times higher than the aluminum II. Aluminum deforms elastically three times as much as does steel III. Steel will show much smaller changes in dimensions IV. Steel is three times stiffer than the aluminum V.Aluminum is three times stiffer than the steel

Please select the correct answers according to the given figure for the elastic behaviour of steel and aluminium I. The elastic modulus of steel is about three times higher than the aluminum II. Aluminum deforms elastically three times as much as does steel III. Steel will show much smaller changes in dimensions IV. Steel is three times stiffer than the aluminum V.Aluminum is three times stiffer than the steel

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Mild steel 1 Young;s modulus 1219.5 Yield strain and stress (0.4101,500.08) Failure stress and strain :not able to find because the given data shows the experiment did not reach the failure point. if the material stress and strain does not reach a failure point ,what dose it means , does it means that the material is more stronger?
Read the question carefully and give me both A&B right solutions otherwise leave it. A) Steel Alloy rod made of Stainless Steel 304 is subjected to 60 kip of Tensile force. Steel rod is having diameter of 1 in. and Length of 8 in. Determine change in its length and diameter. Consider material behaves elastically. For determining material properties use Mechanical property table. B) An aluminium specimen made up of 6061-T6 Material has a diameter of d = 20 mm and a gage length of L0= 300 mm. If a force of 135 kN elongates the gage length 0.9 mm, determine the modulus of elasticity. Also, determine contraction of diameter.
And **The modulus of elasticity** (MPa) I need a clear step by step answer please :)
The yield strength of a high-strength steel is 1 GN/m2 and KIC is 100 MPa √m. The crack length that can cause sudden failure at half of its yield strength is ____mm. (Round off to two decimal places)
Fatigue data of steel is showed in the following stress-cycle curve.Write down the values of steel endurance limit and steel fatigue strength at 10^5 cycles in the spaces provided below.Steel Endurance Limit: _____ ksiteel Fatigue Strength at 10^5 cycles: _____ ksi
Which one(s) of the following about G, shear modulus of elasticity of a material are correct? select all which are correct. G is also called the modules of rigidity. G is related to the modulus of elasticity E and Poisson’s ratio . G is usually smaller than Young's modulus E for the same material. G is the ratio of shear stress to shear strain when the material's proportional limit in shear has not been exceeded.
Note: Kindly give me both right answers. A) Did the ductile materials (annealed and aluminium) react differently to the two different testing methods (hardness test vs. tensile test)? What does this say about the behaviour of ductile materials in compression vs. tension? B) Did the brittle material (quenched) react differently to the two different testing methods (hardness test vs. tensile test)? What does this say about the behaviour of brittle materials in compression vs. tension? （Three to five sentence answers are good）（engineering material)
Experiments were conducted in a tension testing machine to evaluate the material properties of two metallic rods both having diameter equal to 10 mm. First rod having modulus of rigidity of the material equal to 400 tonnes/cm2 when subjected to an axial tensile force of 6 kN, the change in its diameter was observed to be 0.0018 cm. The value for the bulk modulus of the second metallic rod is same as that of the first one but modulus of elasticity 18% more. Based on the material properties calculate and compare the values of different moduli as well as Poisson’s ratio for both metallic rods. Justify your answer with reasons.
Determine the tensile yield strength (0.2% offset) and the maximum strength of a metal alloy having the following tensile stress-strain diagram. Select one: The tensile yield strength Sy = 100 Mpa and the maximum strength Smax = 250 Mpa. The tensile yield strength Sy = 170 Mpa and the maximum strength Smax = 250 Mpa. The tensile yield strength Sy = 150 Mpa and the maximum strength Smax = 200 Mpa. The tensile yield strength Sy = 240 Mpa and the maximum strength Smax = 250 Mpa. The tensile yield strength Sy = 80 Mpa and the maximum strength Smax = 250 Mpa.
Consider the tensile stress-strain diagram below. If samples 1 and 2 are identical except that they were tested at different temperatures, which sample was tested at a lower temperature? Note: This question will be marked negatively so consider your answer carefully. A. Sample 1 B. Both were tested at the same temperature/ Alby is by die dieselfde temperatuur getoets C. Sample 2
A cylindrical rod 500 mm long, having a diameter of 12.7 mm, is subjected to a tensile load of 30,000 N. The rod is to experience an elongation not more than 1.3 mm and FOS ≥ 1.5 setting yield strength as a criteria. Additional constraints to be met are max specific stiffness and %EL not more than 0.15. Which of the below listed materials are possible candidates? Justify your choice(s) by making a table of constraints. Materials Modulus of Elasticity, (GPa) Yield Strength, (MPa) Tensile Strength, (MPa) Aluminum alloy 70 300 450 Titanium alloy 107 400 550 Steel alloy 207 500 750
a)Define the following mechanical properties which can be derived and, in each case, state the appropriate unit. i)Engineering stressii)Yield stress leveliii)Young’s modulusIv) Ultimate tensile stressv)Ductilityvi) Toughness B) Briefly describe a standard test method which can be used to establish properties (ii), (iii) and (iv) mentioned in part (a) of this question. Also provide a sketch of the apparatus.