Please show your solutions clearly. Show your FBD or illustrations. 1. (a) Find the tension in each cable supporting the 600N cat burglar (b) Suppose the horizontal cable were reattached higher up on the wall. Would the tension in the other cable increase, decrease or stay the same? Why? 37 600 N

Please show your solutions clearly. Show your FBD or illustrations. 1. (a) Find the tension in each cable supporting the 600N cat burglar (b) Suppose the horizontal cable were reattached higher up on the wall. Would the tension in the other cable increase, decrease or stay the same? Why? 37 600 N

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.62P: The bar ABC is supported by three identical, ideal springs. Note that the springs are always...

See similar textbooks

Similar questions

A 150-lb rigid bar AB. with friction less rollers al each end. is held in the position shown in the figure by a continuous cable CAD. The cable is pinned at C and D and runs over a pulley at A. (a) Find reactions at supports A and B. (b) Find the force in the cable.
A uniform drawbridge must be held at a 38.5 ∘ angle above the horizontal to allow ships to pass underneath. The drawbridge weighs 45000 N, is 13.0 m long, and pivots about a hinge at its lower end. A cable is connected 3.80 m from the hinge, as measured along the bridge, and pulls horizontally on the bridge to hold it in place. a) What is the tension in the cable? b) Find the magnitude of the force the hinge exerts on the bridge. Find the direction of the force the hinge exerts on the bridge. c) If the cable suddenly breaks, what is the initial angular acceleration of the bridge?
A boom hinged at the base of a vertical mast is used to lift a 2000 load. Find the tension in the cable and the reaction R the end of the boom. The angle of the boom is 40 degrees with the horizontal and the cable is 60 degrees with the vertical mast. Show complete solution including FBD.
A horizontal board weighing Wb = 600 N is hinged to a vertical wall. A personweighing Wp = 400 N stands at the end of the board 5 m from the wall. A rope is attached to theboard at a point 3 m from the wall and makes an angle of θ = 40° with theboard. Determine the tension (T) in the rope
The boom of the wall crane 4m long is held at right angles to the wall by a wire that is attached to the wall 3m above the foot of the boom. If the load lifted is 45000N, find the tension in the wire and the compression force in the boom Neglect the weight of the boom. May I also ask mam/sir for the Diagram and explanation?
Draw the free body diagram for this problem: The boom of the wall crane 4m long is held at right angles to the wall by a wire that is attached to the wall 3m above the foot of the boom. If the load lifted is 45000N, find the tension in the wire and the compression force in the boom. Neglect the weight of the boom.
....An electric motor drives a compressor by use of V-belt. The angle of contact on the smaller pulley is 2.89 rad and the belt speed runs at 29.36 m/s. The groove angle of the pulleys is 35°. Determine the tension in the slack side of the belt in N if the belt has a cross-sectional area of 366 mm2, density 1000 kg/m3, and an allowable tensile stress of 2.3 MPa. The coefficient of friction between the belt and the pulley is 0.3
Q)Two blocks A=150 N and B=? are connected by a rod at their ends by frictionless hinges as shown in the Fig. Find the weight of block B required for limiting equilibrium of the system, if µ = 0.35 at all sliding surfaces.
A 110-kg uniform ladder is tied at its bottom on the wall using a wire shown in the figure. The floor is frictionless, while the wall is rough. The maximum tension on the wire is 180 N. (a) What is the normal force exerted by the wall on the ladder? (b) What is the frictional force exerted by the wall to the ladder?
Two weights, A and C, are fixed to a bar, B. Their masses are: A = 60 kg, B = 230 kg,C = 45 kg. B is, in turn, connected to a fixed vertical post by a hinge and a support cableD. The geometry of the system is shown at right. Treat weights A and C as point masses a)What is the tension in support cable D? Be sure to include a detailed freebody diagram to accompany your analysis.b) What is the magnitude of the force provided by the hinge?c) What is the moment of inertia of the A + B + C as a rigid system, for rotationabout the hinge? For analysis, break the beam into a short piece to the left of thehinge, and a separate longer piece to the right of the hinge. If the support cable D on should break,d) what is the angular acceleration of the beam and weights at the moment the cable breaks?e) what is the magnitude of the linear acceleration experienced by each of the weights, A and C, at moment the cable breaks?
A sign hangs from a rod as shown in the figure. The rod is attached to a wall with a frictionless hinge and a wire. The weight of the sign is 125 N, and the weight of the rod is 20 N. Determine the tension force in the wire.
A uniform trapdoor shown below is 1.0 m by 1.5 m and weighs 300 N. It is supported by a single hinge (H), and by a light rope tied between the middle of the door and the floor. The door is held at the position shown, where its slab makes a 30° angle with the horizontal floor and the rope makes a 20° angle with the floor. Find the tension in the rope and the force at the hinge.