Plot the Iron-Iron Carbide phase diagram label all phases and temperatures, =answer the following:a-Show the heating ranges for main heat treatmentsLabel and thanb-What are the upper and lower critical temperatures for 0.8 %C steelc-For alloy containing 3% C find the mass fraction of phases and composition in 1000°C,and 700 °C.

Phase Diagram- it is a graphical reprsentation of the effect of temperature and composition upon…

Plot the Iron-Iron Carbide phase diagram label all phase 400 answer the following: a-Show the heating ranges for main heat treatments b-What are the upper and lower critical temperatures for 0.8 %C steel c-For alloy containing 3% C find the mass fraction of phases and composition in 1000°C,and 700 °C.

Plot the Iron-Iron Carbide phase diagram label all phase 400 answer the following: a-Show the heating ranges for main heat treatments b-What are the upper and lower critical temperatures for 0.8 %C steel c-For alloy containing 3% C find the mass fraction of phases and composition in 1000°C,and 700 °C.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. Given the time-temperature transformation diagram, what would be the phases present for a 1.13 wt. % C steel with no alloying elements. calculate the amount of pro eutectoid product, where applicable (at the bottom) A) quenched in cold water to 650 C in 0.1 seconds, then held at 650 C for 5 seconds, then quenched to 400 C, held at 400C for 60 seconds, and finally quenched to room temperature B. Necessary Steel Phase Diagram Calculations to determine the amount of pro eutectoid product:
Suppose you wanted to have two samples of NiTi wire: one that is in the high-temperature austenite phase at 0°C, and one that is in the low-temperature martensite phase at 0°C. Which of the compositions of NiTi below would you choose for which sample? Composition A: 50% Ni, 50% Ti Composition B: 52% Ni, 48% Ti
Using the Tin_Lead phase diagram, at 40% tin at 200C, what is the composition of the liquid phase? and how much of hte material is in that phsae?
A binary eutectic lead-tin phase diagram is shown in Figure 2. Consider the case of 300 grammes of a 70–30 wt% Cu–30 wt% Ag alloy that is gently heated. The -phase refers to a silver-rich solid solution, whereas the -phase refers to a copper-rich solid solution. a)Design a composition of Cu-Ag alloy that will exist completely molten stage at 900oCand becomes completely solid at 800oC.
Answer the following questions using the phase diagram of iron and iron carbide below:For a 99.70 wt% Fe–0.30 wt% C alloy at a temperature of 600oC, determine the following:a. The fractions of total ferrite and cementite phases b. The fractions of the pro eutectoid ferrite and pearlite
1. Given the time-temperature transformation diagram, what would be the phases present for a 1.13 wt. % C steel with no alloying elements. calculate the amount of pro eutectoid product, where applicable (at the bottom) A.) quenched in cold water to 380 C in 0.1 seconds, then held at 380 C for 30 seconds, then quenched to room temperature B.) cooled in air at 2 C/minute to 600oC, then quenched to room temperature C. quenched in cold water to 550 C in 0.1 seconds, then held at 550 C for 2 seconds, then quenched to room temperature D. Necessary Steel Phase Diagram Calculations to determine the amount of pro eutectoid product:
Use the Lead-Tin (Pb-Sn) phase diagram below to answer the following questions: Place the following microstructures in the correct order of formation for slowly cooling a 98 wt% Sn alloy from 300 °C to room temperature (point A to point B).
Use the copper silver phase diagram below. 100g of a 40 wt% Cu 60 wt% Ag alloy is made and cooled from liquid form. a. At what temperature does the solid phase start to appear? b. What phases exist at 780°C? c. What are the compositions (Cu and Ag%) of the phases in question b? d. What are the weights (in g) of Cu in the solid phase and liquid phase in question b?
Iron carbon phase diagram extends up to 6.7% carbon only, why? (Mention two reasons)Single line text.
Part C. Which type of phase transformation is important in heat treatment of steels? (circle one)Peritectic Eutectic Eutectoid Incongruent meltingAt what temperature and overall composition wt% C, does it occur?Write the reaction equation for this transformation, and briefly describe the nature of each of the three important phases that are involved.
Draw the iron-Fe3C phase diagram. Consider 0.4 and 1.1 wt% C steel alloy. It is cooled slowly from a temperature within austenite phase to room temperature. Show a) microstructure at 1000 °C b) microstructure at 730°C c) microstructure at 715°C and d) microstructure at room temperature e) determine the phase present, the phase compositions at 715 and 730 °C f) What do you say about mechanical properties of these alloys, depending on their microstructure at room temperature?
Material science Assuming this system forms a laminar type eutectic, determine the volume proportion of phases for an equilibrium solidified 50% Pb alloy. Sketch the expected microstructure.