Plot the response of the system shown above for the following conditions: a. There is no damper b. Cea = C/2 c. Ceg = 3 c/2 d. Cea = C Provided that the initial conditions are: initial velocity = 0 m/s and initial displacement is 10 mm.

Plot the response of the system shown above for the following conditions: a. There is no damper b. Cea = C/2 c. Ceg = 3 c/2 d. Cea = C Provided that the initial conditions are: initial velocity = 0 m/s and initial displacement is 10 mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Exercise 3: Damped forced vibration. Find the solution ofu′′ +(1/8)u′ + u = 3 cos(ωt), u(0) = 2, u′(0) = 0 using sympy.dsolve for ω = 0.3 and ω = 1. Plot the solution, transient solution and steady-statesolution in a common plot for 0 < t < 10 for ω = 0.3 and ω = 1 respectively. Exercise 4: Undamped forced vibration. Plot the solution ofu′′ + u = 3 cos(ωt), u(0) = 0, u′(0) = 0 for 0 < t < 10 for ω = 0.3 and ω = 1 respectively. (You may find the solution either numerically with scipy.integrate.solve ivp, scipy.integrate.odeint or by finding and plotting the symbolic solution via sympy.dsolve)Remark: The vibration consists of beats; in the critical case ω = 1 solutions do not stay bounded
Suppose a spring with spring constant 7 N/m is horizontal and has one end attached to a wall and the other end attached to a 2 kg mass. Suppose that the friction of the mass with the floor (i.e., the damping constant) is 1 N⋅s/m a) Set up a differential equation that describes this system. Let x to denote the displacement, in meters, of the mass from its equilibrium position, and give your answer in terms of x,x′,x′′. Assume that positive displacement means the mass is farther from the wall than when the system is at equilibrium. b) Find the general solution to your differential equation from the previous part. Use c1 and c2 to denote arbitrary constants. Use t for independent variable to represent the time elapsed in seconds. Your answer should be an equation of the form x=… c) Enter a value for the damping constant that would make the system critically damped. ?Ns/m
A machine is represented as a single degree of freedom spring-mass-damper system. The machine has a total mass of (109)kg, an out-of-balance mass 0.125 kg, eccentricity of 0.01 m, coefficient of damping (109)N/ (m/sec), and spring stiffness (1009) N/m. The rotational speed of the machine is 3000 rpm. Determine the maximum amplitude of vibration due to out-of-balance. Suggest a method for the control of vibration caused due to out-of-balance.
(b) Consider a vertical spring mass-damper-system with mass m = 2 kg, damping coefficient c = 5 N.s/m and stiffness k = 10 N/m. An external force f(t) = sin3t N is applied to the mass. (i) Find the static equilibrium position as measured from the un-stretched length of the spring (ii) Write the equation of motion. (iii) Find the natural and damped frequencies. (iv) In steady state, find the time delay in seconds between the mass position and f(t). (v) Find the steady state maximum acceleration.
MECH Vibrations: Arbitrary input function A forcing function equivalent to an absolute sine function (i.e., |sin(x)|), with a magnitude of F0,and period of T, is applied at t = 0 [s] to a spring-mass system with the following parameters: F = F0*|sin(x)|m = 72 [kg]k = 112 [N/m]F0 = 721 T = 9 dt = 9/1000 x0 = 1 m/sv0 = -1 m/s Using numerical methods, solve for the response of the system.
A spring-mass-damper system oscillating about the horizontal surface is subjected to anexternal force of F = 300 sin (6)(t), where 300 is in Newtons and 6 is in radians per second. Thesystem has a mass 90 [kg], a damping coefficient of 78 [N ⋅ s/m] and a spring constant of300 [N⁄m]. The system is both given an initial displacement of 1.2 [m] and an initial velocity of 1.4[m⁄s].a. Using Method of Undetermined Coefficients, determine the particular solution for thedisplacement function.b. Determine the unknown coefficients for the homogeneous solution using the initialconditions (Note: the external force already works at t = 0).c. Determine the position, velocity, and acceleration of the system after 10 seconds.
Determine the steady state time response x(t) of a viscously damped system subjected to harmonic base excitation for the following data : m = 15 kg, c = 25 N.s/m, k = 300 N/m, y(t) = 0.04 sin ( 5t ) m. %3D
Vibrations Question The governing equation of motion for a base motion system is given by (assume the units are Newton) mx''(t)+ cx'(t)+kx(t)=cYwbCos(wb*t)+kYSin(wb*t)Given that m = 180 kg, c = 30 kg/s, Y = 0.02 m, and wb= 3.5 rad/s Find the largest value of the stiffness, k that makes the transmissibility ratio less than 0.85
A single degree of freedom mass-spring-damper system is subject to vibration under the influence of a harmonic force. On my site, it is given as m=2 kg, k=800 N/m, c=64 Ns/m. The amplitude of the harmonic force is F0=256 N and its frequency is w= 20 rad/s. Answer the questions in options a, b, and c according to the given information. 1) Calculate the damping ratio of the system (ξ) a.1 b.0.7 c.0.9 d.0.8 2)Calculate the magnification factor (M) of the system. a.0.86 b.1.25 c.0.312 D.0.625 3-) Calculate the maximum vibration amplitude (X) (meters). a.0.2 b.0.1 c.0.4 D.0.3
1.block diagram physical meaning and the time response for different inputs
F(t)=mx''+kx'+cxIf the initial conditions are zero, that is, x'(0) = 0 and x(0) = 0 and F(t) is a harmonic load, then is the system response transient? If the mass of the system increases, how does this influence the natural frequency of the system and the time it takes to reach steady state? If the stiffness constant of the system is decreased, does the frequency of the steady state response change?Does the response of the system in steady state depend on its initial conditions? Taking into consideration that the vibration frequency in the transient regime is ωd =ωnsqrt(1-b), how does the magnitude of the damping constant c affect the response of the system in the transient regime?
A car repair shop has 3 stages of process serially to performcare of its customers' cars. Process 1 with Reliability R1 of 0.91 performedby Staff A, Process 2 with Reliability R2 of 0.92 and Process 3 withReliability R3 of 0.96 a. Sketch from the process above b. Calculate the System Reliability Rs of the systemc. If the workshop has a System Reliability standard of 0.88, whether thethe workshop is able to meet these standards? Explain your answerd. The workshop manager decided to make redundancy by adding staffprocess 1 with Reliability R1.1 of 0.92 and Process 2 with ReliabilityR2.1 is 0.93. Sketch from the process above e. What is System Reliability now? Is able to meet System standardsReliability workshop? Explain your answer