The mass, damping, and stiffness of the system C k can be adjusted to produce different dynamic responses. Match the frequency response functions (A)-(D) with their corresponding time-histories (W)-(Z).

The mass, damping, and stiffness of the system C k can be adjusted to produce different dynamic responses. Match the frequency response functions (A)-(D) with their corresponding time-histories (W)-(Z).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The block diagram given below; A) Reduce it B) G1(s)=2/s ; G2(s)=1/4s+2 ; G3(s)=4 ;H(s)=0.5 Given the values of the system; find the time constant, its natural frequency and damping rate and explain what kind of dynamic behavior it exhibits accordingly. C)Find the poles and zeros of the system according to the values in (B).Is the system stable? Find the unit step response (Inverse Laplace).
A vibrating system with mass 3 kg, stiffness 21 N-s/m and damper having damping coefficient 10 N-s/m When an exciting force of magnitude 27 sin2t is acting, what would be the time period of oscillations?
A heat exchanger system is depicted in the following figure and related system parameters are given at the table below. Suppose that the rate of heat energy gain for this system satisfies the simple material transport model; where, i represents the mass flow, T and I are the entering and leaving fluid temperature and cis specific heat capacity of fluid. Then, derive a frequency-domain model to calculate the temperature of Fluid-B leaving the heat exchanger. L K R₁, R Fluid-B→→→→→→ TAN 9 gained mc (Tx-TN) = Fluid-A TB BN TAX : Height of heat exchanger cylinder : Thermal conductivity of heat exchanger cylinder Radius of inner and outer tube : Thickness of inner and outer tube ri, ro A₁, A: Surface area of inner and outer tube C₁, C TAN, TAX → Fluid-A TR BX Fluid-B : Convective heat transfer coefficient of inner and outer tube Temperature of Fluid-A at entrance and exit TBN, TBX: Temperature of Fluid-B at entrance and exit C₁, C Heat capacity of Fluid-A and Fluid-B
Sketch the level response for a bathtub with cross-sectional area of 8 ft 2 as a function of time for the following sequence of events; assume an initial level of 0.5 ft with the drain open. The inflow and outflow are initially equal to2ft3/min.(a)The drain is suddenly closed, and the inflow remains con-stant for 3 min (0≤t≤3).(b)The drain is opened for 15 min; assume a time constant in a linear transfer function of 3 min, so a steady state is essentially reached (3≤t≤18) (c)The inflow rate is doubled for 6 min (18≤t≤24).(d)The inflow rate is returned to its original value for 16 min(24≤t≤40).
A velocity of a vehicle is required to be controlled and maintained constant even if there are disturbances because of wind, or road surface variations. The forces that are applied on the vehicle are the engine force (u), damping/resistive force (b*v) that opposing the motion, and inertial force (m*a). A simplified model is shown in the free body diagram below. From the free body diagram, the ordinary differential equation of the vehicle is: m * dv(t)/ dt + bv(t) = u (t) Where: v (m/s) is the velocity of the vehicle, b [Ns/m] is the damping coefficient, m [kg] is the vehicle mass, u [N] is the engine force. Question: Assume that the vehicle initially starts from zero velocity and zero acceleration. Then, (Note that the velocity (v) is the output and the force (w) is the input to the system): 1. What is the order of this system?
A velocity of a vehicle is required to be controlled and maintained constant even if there are disturbances because of wind, or road surface variations. The forces that are applied on the vehicle are the engine force (u), damping/resistive force (b*v) that opposing the motion, and inertial force (m*a). A simplified model is shown in the free body diagram below. From the free body diagram, the ordinary differential equation of the vehicle is: m * dv(t)/ dt + bv(t) = u (t) Where: v (m/s) is the velocity of the vehicle, b [Ns/m] is the damping coefficient, m [kg] is the vehicle mass, u [N] is the engine force. Question: Assume that the vehicle initially starts from zero velocity and zero acceleration. Then, (Note that the velocity (v) is the output and the force (w) is the input to the system): A. Use Laplace transform of the differential equation to determine the transfer function of the system.
What is the step response of the dynamic system pictured below?
A block spring system oscillates in a simple harmonic motion on africtionless horizontal table, its displacement varie with times according to x(t)=0,2cos(2t_3.14/4) the earliest time the particle reaches position x=0,1m is
A 1.5-kg mass attached to an ideal massless spring with a spring constant of 20.0 N/m oscillates on a horizontal, frictionless track. At time t = 0.00 s, the mass is released from x = 0.0 cm with a velocity of 0.370 m/s to the left. Find the followingA. Time periodB. Total mechanical energy of the massC. AmplitudeD. Phase constant of motion. Discuss the two possible values of phase constant you get and explain how you arrived at the correct answer. Write the equation of motion.E. Maximum acceleration of the mass. (Acceleration is maximum when it ispositive). How long after the release does the maximum acceleration occur?F. Draw the position-time graph for one cycle of motion.
If a mass of 6 kg oscillates on a spring having a mass 3 kg and stiffness 11200 N/m, then the natural frequency of the system in rad/sec will be
A certain mass is driven by base excitation through a spring (Figure P4.13). Its parameter values are m = 100 kg, c = 1000 N * s/m, and k = 10,000 N/m. Determine its peak frequency w_p, it’s peak M_p, and its bandwidth.
2.A 31 kg skip attached to a steel rope on a crane is used to hoist bricks from the ground to the top of a construction site. The steel rope is wound onto a lifting drum with a diameter of 700 mm and rotational frequency of 52 revolutions per minute. The lifting drum is situated on the top floor which is 196 m high. How many seconds will it take to lift bricks, three quarters up the height of the building?