Pressure in accelerated rigid body motions we use the small, cubical element of fluid shown in Figure below and consider it to be part of a larger mass of fluid. If the fluid was being accelerated, then the sum of the forces acting on it, in the direction of the acceleration, must equal the mass times the acceleration. For the cubical element of fluid being accelerated in the vertical direction, we rewrite as

Pressure in accelerated rigid body motions we use the small, cubical element of fluid shown in Figure below and consider it to be part of a larger mass of fluid. If the fluid was being accelerated, then the sum of the forces acting on it, in the direction of the acceleration, must equal the mass times the acceleration. For the cubical element of fluid being accelerated in the vertical direction, we rewrite as

Name: Pressure in accelerated rigid body motionswe use the small, cubical e
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Pressure in accelerated rigid body motionswe use the small, cubical element of fluid shown in Figure below and consider it to be part of a largermass of fluid. If the fluid was being accelerated, then the sum of the forces acting on it, in the direc

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The water level in the 1.8 m high and 1 m diameter cylindrical tank in the figure is 1.4 m. If this tank is rotated around its own axis at what speed will the axial depth be zero? (In other words, what is the number of revolutions at which a dry area will begin to form at the bottom of the tank?) Take the gravitational acceleration as 10 m / s2 and π as 3.
A 118-mm-diameter pipe enlarges to a 149-mm-diameter pipe. At section 1 of the smaller pipe, the density of gas in steady flow is 264.656 kg/m3, and the velocity is 23 m/s; at section 2 of the larger pipe, the velocity is 15 m/s. Find the unit weight (in kN/m3) of the gas at section 2. Round off to three decimal places.
The open trapezoidal tank shown in the figure is initially filled with oil (SG = 0.80) up to adepth of 2 meters. It was subjected to an unknown rightward acceleration, ax, and a downward acceleration, ay, equal to 3 m/s2.a.) If after the acceleration, the oil depth is 1.5 m, determine the value of ax. Assume unit width.b.) Calculate the pressures at A and B during the acceleration.
The three-legged manometer in Fig. is filled with water to a depth of 20 cm. All tubes are long and have equal small diameters. If the system spins at an angular velocity about the central tube, (a) derive a formula to find the change of height in the tubes; (b) find the height in cm in each tube if ω = 120 r/min.
In the manometer above, point 2 is open and is exposed to the surroundings. Also, the water tank is pressurized by air from the inside as shown in the figure. If h1 = 22cm, h2 = 0.35m, and h3 = 47cm, and assuming that the acceleration due to gravity is 9.81m/s2, (density of water = 1011 g/L, density of oil = 770 kg/m3, density of mercury has a density of 13.75 kg/dm3) A) Calculate the gauge pressure (in torr) of the air inside the tank. B) Show in your diagram all the parts that can be cancelled in the pressure balance. C) Calculate the pressure at point C (in kPa).
Two vertical and connected cylindrical tanks of diameter D are open to the atmosphere and they contain water at a height of h in the initial state, as shown in the figure. As the radial blades in the left tank are rotated about the centerline of the tank, some water in the right tank flows into the left tank. Determine the angular velocity of radial blades ? such that half of water in the right tank flows into the left tank. Also, derive a general relation for angular velocity as a function of initial height of water in the tank. Assume water in the tanks would not spill. D = 2R = 45 cm, h = 40 cm and g = 9.81 m/s2.
Q5: The U-tube shown in figure (3), in filed with water and rotated about a vertical axis (0.15m) to the right of (A) For a gage pressure at (A) equal to zero Determine the rotational speed in (r.p.m)
Find the surface tension of the water droplet of 30 mm diameter when the inside pressure is 3.5 N/m2 The surface tension in N/m is
Open tank (4.5 m long, 2.5 m height and 3 m wide) contains liquid (S-0.75) to height 1. m. If this tank is accelerated along its length on a horizontal truck at a constant value of 3.5 m/s, determine pressure at the bottom of the tank at front and rear edges (in kN/m). (take y=9.8 kN/m for water)
The distance between the two plates, which are 2 m x 2 m in size and parallel to the earth surface, is 9 mm, and there is water at 20 ° C between them. Find the force in (N) to be applied to pull the top plate to the right at 10 m / s.
2 plates move as indicated with oil on top and water underneath V_T -> h_1 = 1mm h_2 = 2mm V_B = 8 m/s V_T = 2 m/s plate area = 5m^2 liquids SAE-30W Water a) draw velocity profile on vertical dotted line in... b) create a parametric equation for Vw and Vo c) calculate τ between liquids d) calculate force (F=τA)
A tank of water 5m deep receives a constant upward acceleration az= 4 m2/sec, determine the gauge pressure at the tank bottom in pascal is: *