A vertical U-tube partially filled with alcohol (SG= 0.99) is rotated at a specified rate about its left arm. Compute for the follow (a) angular velocity of the tube's rotation if the alcohol is on the brink of spilling (b) pressure at point B during the rotation of the tube Please provide explanation per line of solution. thanks

A vertical U-tube partially filled with alcohol (SG= 0.99) is rotated at a specified rate about its left arm. Compute for the follow (a) angular velocity of the tube's rotation if the alcohol is on the brink of spilling (b) pressure at point B during the rotation of the tube Please provide explanation per line of solution. thanks

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Roman aqueduct customersobtained extra water by attaching a diffuser to theirpipe exits. Fig. shows a simulation: a smooth inletpipe, with or without a 15° conical diffuser expanding to a5-cm-diameter exit. The pipe entrance is sharp-edged. Calculatethe fl ow rate (a) without and (b) with the diffuser.
Torricelli’s idealization of effl ux from a hole in the side ofa tank is V = √2 gh, as shown in Fig. P3.81. The cylindricaltank weighs 150 N when empty and contains water at20 °C. The tank bottom is on very smooth ice (static frictioncoeffi cient ζ ≈ 0.01). The hole diameter is 9 cm. For whatwater depth h will the tank just begin to move to the right?
Derive an expression for the capillary- height change h, as shown, for a fluid of surface tension Y and contact angle 0 be- tween two parallel plates W apart. Evaluate for water at 20°C if W = 0.5 mm.
The cylindrical water tank in Fig. is being fi lled ata volume fl ow Q 1 = 1.0 gal/min, while the water alsodrains from a bottom hole of diameter d = 6 mm. At timet = 0, h = 0. Find and plot the variation h ( t ) and the eventualmaximum water depth h max . Assume that Bernoulli’ssteady-fl ow equation is valid.
A cylindrical tank 0.9 m in radius rests atop a platform 6 m high. Initially the tank is filled with water (p = 1 x 103kg/m3) to a depth ho= 3 m. A plug whose area is 6.3 cm2 is removed from an orifice in the side of the tank at the bottom. What is the speed of the stream as it strikes the ground?
The 1m diameter tank is initially filled with gasoline. There is a 3.1 cm diameter orifice in the bottom. If the orifice is suddenly opened, estimate the time (minutes) for the fluid level to drop from 2m to 1.5 m. Use SG (gas) = 0.7, Cd = 0.66. answer in 2 decimal places.
A 150 mm diameter open circular cylinder is 1 m long and contains water up to a height of 0.7 m. Estimate the speed at which the cylinder may be rotated about its vertical axis so that the axial depth becomes zero. a. 249. b. 163.93 c. 564 d. 296
Determine the pressure drop over a reducer with the following conditions: Fluid density: 25 kg/m3Fluid velocity: 1.5 m/sFluid viscosity: 0.001 Pa*sInlet diameter: 0.12 mOutlet diameter: 0.019 mPipe absolute roughness: 4e-4 m Give your final answer in Pa, rounded to the nearest whole number. [Ignore entrance/exit losses and velocity loss terms]
Discuss which dimensionless pump performance parameter is typically used as the independent parameter. Repeat for turbines instead of pumps. Explain.
pllllzzzz help me right nowww plzzz The belt moves at a steady velocity V and skims the top of oil tank. Assuming a linear velocity profile in the oil, what is the required belt-drive power P (watt) (P= power = force x Velocity) if the belt moves at 3.5 m/s over oil with specific gravity of S=3.6 and oil viscosity of 0.004 m2/s. Belt geometry L= 2 m, b = 60 cm, and oil depth is h = 3 cm?
The head loss for a certain circular pipe is given by hL = 0.0826fL(V.2/D5), where f is the friction factor (dimensionless), L is the pipe length, V. is the volumetric flow rate, and D is the pipe diameter. Determine if the 0.0826 is a dimensional or dimensionless constant. Is this equation dimen sionally homogeneous as it stands?
A pump discharges 8000 liters per minute of a certain brine solution (SG=1.20) to an evaporating pond. The intake line is 25cm in diameter and is at the same level as the pump discharge line, which is 15cm in diameter. The pressure at the inlet of the pump is -170mm of mercury. The pressure gage connected to the pipe discharge reads 150 kPa, and its center is 2.0mabove the center of the discharge flange. The vapor pressure of the brine solution is 40mm of Hg. If the pump efficiency is 80%. How much power is required?