5-6 Pressure makes the viscosity of liquidsO A. increaseB. decreaseO c. remains the sameD. increase or decrease, depending on its viscosityO E. None of these. Which among the ff is not included in combined momentum flux tensor p?A. Molecular stressB. Convective forceO c. Gravity forceD. Pressure forceO E. None of these.

Explanation Both kinematics and dynamic viscosity are independent of variation of pressure.with…

Answered: Pressure makes the viscosity of liquids

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

can u explain questions Q3 more clearly and am I able to apply the momentum formula ?
While rotating at 900 rpm, a centrifugal pump delivers 2500 gpm of water at ahead of 75 ft. If the impeller diameter is 1.5 ft. and the blade width is 1.75 in.,find the (a) blade angle β2, (b) radial velocity Vr2, and (c) blade speed u2. Assumeno whirl at the inlet.Ans: β2=12.5°; Vr2=8.1 ft./s; u2=70.7 ft./s
Write the mathematical form of prinicple of linear impulse and momentum.
Steam enters a horizontal turbine at 350 lbf/in 2 absolute,580 ° C, and 12 ft/s and is discharged at 110 ft/s and 25 ° Csaturated conditions. The mass fl ow is 2.5 lbm/s, and theheat losses are 7 Btu/lb of steam. If head losses are negligible,how much horsepower does the turbine develop?
A centrifugal pump discharged 20 L/s against a head of 17 m when the speed is 1500 rpm. The diameter of the impeller was 38 cm and the brake horsepower is 6. A geometrically similar pump 49 cm in diameter is to run at 1750 rpm, assuming equal efficiencies, what brake power is required in Hp?
An 8-in model pump delivering 180°F water at 800 gal/minand 2400 r/min begins to cavitate when the inlet pressureand velocity are 12 lbf/in2 absolute and 20 ft/s, respectively.Find the required NPSH of a prototype that is4 times larger and runs at 1000 r/min.
A jet of water 3 cm in diameter strikes normal to a plate asin Fig. If the force required to hold the plate is 23 N,what is the jet velocity?( a ) 2.85 m/s, ( b ) 5.7 m/s, ( c ) 8.1 m/s, ( d ) 4.0 m/s, ( e ) 23 m/s
Please solve this problem using momentum concept
In Prob. it would be difficult to solve for Ω because of itappears in all three of the dimensionless pump coefficients.Suppose that, in Prob. 5.61, Ω is unknown but D = 12 cmand Q = 25 m 3 /h. The fluid is gasoline at 20 ° C. Rescale thecoefficients, , to make a plot ofdimensionless power versus dimensionless rotation speed.Enter this plot to find the maximum rotation speed Ωforwhich the power will not exceed 300 W.
A fi reboat pump delivers water to a vertical nozzle with a3:1 diameter ratio, as in Fig. . If friction is neglectedand the fl ow rate is 500 gal/min, how high will the outletwater jet rise?( a ) 2.0 m, ( b ) 9.8 m, ( c ) 32 m, ( d ) 64 m, ( e ) 98 m
A certain axial flow turbine has an output torque M that isproportional to the volume flow rate Q and also depends onthe density ρ , rotor diameter D , and rotation rate Ω . Howdoes the torque change due to a doubling of ( a ) D and ( b ) Ω ?
The pressure of the water base of a Pelton Wheel is 4850 kPa and the velocity at the same point is 6 m/s. The jet diameter is 20 cm, and the velocity coefficient is 0.98 and the turbine’s efficiency is 86%. Find the brake power, in bkw.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS