Prob. 4.5-9. Use the following data with Fig. P4.5-9:G = 11 × 10° psi, L1= 10 in., L2= 15 in., L3 = 20 in.,TA =200 lb · ft, TB = -350 lb · ft, Tc = -150 lb · ft,%3DTp300 lb · ftIf AD is a solid shaft with diameter d = 1.5 in., determine therelative twist angle (in radians) between ends A and D, thatis, determine ÞD/A = Þp – ¢A. dТАTBTcTDL3P4.5-7, P4.5-8, and P4.5-9

Answered: Image /qna-images/answer/b9f1c8fd-ecd1-44f8-be4d-058fa0c59721.jpg

Prob. 4.5-9. Use the following data with Fig. P4.5-9: G = 11 × 10° psi, L1 = 10 in., L2 = 15 in., L3 = 20 in., TA = 200 lb · ft, TB = -350 lb · ft, Tc = -150 lb · ft, %3D Tp = 300 lb · ft %3D If AD is a solid shaft with diameter d = 1.5 in., determine the relative twist angle (in radians) between ends A and D, that is, determine Þp/A = Þp – ¢A-

Prob. 4.5-9. Use the following data with Fig. P4.5-9: G = 11 × 10° psi, L1 = 10 in., L2 = 15 in., L3 = 20 in., TA = 200 lb · ft, TB = -350 lb · ft, Tc = -150 lb · ft, %3D Tp = 300 lb · ft %3D If AD is a solid shaft with diameter d = 1.5 in., determine the relative twist angle (in radians) between ends A and D, that is, determine Þp/A = Þp – ¢A-

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.5.5P: A tubular bar with outside diameterd2= 4.0 in, is twisted by torques T = 70,0 kip-in. (see figure)....

See similar textbooks

Similar questions

Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the adequacy of both the pipes. In the test, the pipe structure is fixed at A, a concentrated torque of 500 kN - m is applied at x = 0.5 m, and uniformly distributed torque intensity t1= 250 kN m/m is applied on pipe BC. Both pipes have the same inner diameter = 200 mm. Pipe AB has thickness tAB=15 mm, while pipe BC has thickness TBC= 12 mm. Find the maximum shear stress and maximum twist of the pipe and their locations along the pipe. Assume G = 75 GPa.
Two sections of steel drill pipe, joined by bolted flange plates at B, arc subjected to a concentrated torque 4000 kip-in. at x = 3 ft, and a uniformly distributed torque t0= 50 kip-ft/ft is applied on pipe BC. Let G = 11,800 ksi and assume that pipes AB and BC have the same inner diameter, d = 12 in. Pipe AB has a thickness tAB= 3/4 in., and pipe BC has a thickness tBC= 5/8 in. Find the reactive torques at A and C and the maximum shear stresses in each segment.
A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
Solve the preceding problem for the following data: b = 6 in., b = 10 in, L = 110 ft, tan a = 1/3, and q = 325 lb/ft.
Two circular aluminum pipes of equal length L = 24 in. arc loaded by torsional moments T (sec figure). Pipe I has outside and inside diameters d2= 3 in. and L2, = 2.5 in., respectively. Pipe 2 has a constant outer diameter of d2along its entire length L and an inner diameter of d1but has an increased inner diameter of d3= 2.65 in. over the middle third. Assume that E = 10,400 ksi, u = 0.33, and allowable shear stress ra= 6500 psi. Find the maximum acceptable torques that can be applied to Pipe 1; repeat for Pipe 2. If the maximum twist e of Pipe 2 cannot exceed 5/4 of that of Pipe 1, what is the maximum acceptable length of the middle segment? Assume both pipes have total length L and the same applied torque T. Find the new value of inner diameter d3of Pipe 2 if the maximum torque carried by Pipe 2 is to be 7/8 of that for Pipe L If the maximum normal strain in each pipe is known to bemax = 811 x 10-6, what is the applied torque on each pipe? Also, what is the maximum twist of each pipe? Use the original properties and dimensions.
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
A heavy flywheel rotating at n revolutions per minute is rigidly attached to the end of a shaft of diameter d (see figure). If the bearing at A suddenly freezes, what will be the maximum angle of twist <£of the shaft? What is the corresponding maximum shear stress in the shaft? (Let L = length of the shaft, G = shear modulus of elasticity, and / = mass moment of inertia of the flywheel about the axis of the shaft. Also, disregard friction in the bearings at Sand Cand disregard the mass of the shaft.) Hint: Equate the kinetic energy of the rotating flywheel to the strain energy of the shaft.
.17 A mountain-bike rider going uphill applies torque T = Fd(F = l5lb, d = 4 in.) to the end of the handlebars ABCD by pulling on the handlebar extenders DE. Consider the right half of the handlebar assembly only (assume the bars are fixed at the fork at A). Segments AB and CD are prismatic with lengths L, = 2 in.andL3 = 8.5 in, and with outer diameters and thicknesses d01 = 1.25 in. 101 = 0.125 in. and d03 = O.87in.,i03 = 0.ll5in, respectively as shown. Segment BC’ of length L, = 1.2 in. however. is tapered, and outer diameter and thickness vary linearly between dimensions at B and C. Consider torsion effects only. Assume G = 4000 ksi is constant. Derive an integral expression for the angle of twist of half of the handlebar tube when it is subjected to torque T = Fd acting at the end. Evaluate ‘b1-, for the given numerical1ues.
A nonprismatic bar ABC with a solid circular cross section is loaded by distributed torques (sec figure). The intensity of the torques, that is, the torque per unit distance, is denoted t(x) and varies linearly from zero at A to a maximum value T0/L at B. Segment BC has linearly distributed torque of intensity r(x) = T0/3L of opposite sign to that applied along AB. Also, the polar moment of inertia of AB is twice that of BC and the shear modulus of elasticity of the material is G. Find the reaction torque RA. Find internal torsional moments T(x) in segments AB and BC. Find the rotation t0 Find the maximum shear stress tmaxand its location along the bar, Draw the torsional moment diagram (TMD:T(x),0 < x < L).
A uniformly tapered tube AB with a hollow circular cross section is shown in the figure. The tube has constant wall thickness t and length L, The average diameters at the ends are dAand dB= 2dA. The polar moment of inertia may be represented by the approximate formula Ipttd3t4[see Eq. (3-21)]. Derive a formula for the angle of twist e of the tube when it is subjected to torques T acting at the ends.
A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?
Solve the preceding problem if the shaft has an outer diameter d2=150 mm and inner diameter d1= 100 mm. Also, the steel has a shear modulus of elasticity G = 75 GPa, and the applied torque is 16 kN ·m.