Prob.2. The following observations were recorded during á test on a single cylinder oil engine – Bore = 300 mm, stroke = 450 mm, speed = 300 r.p.m., i.m.e.p. = 6 bar, net brake load = 1.5 kN, brake drum diameter diameter = 2 cm. %3D %3D 1.8 metres, brake rope %3D |3D Calculate – (i) Indicated power (ii) Brake power

Prob.2. The following observations were recorded during á test on a single cylinder oil engine – Bore = 300 mm, stroke = 450 mm, speed = 300 r.p.m., i.m.e.p. = 6 bar, net brake load = 1.5 kN, brake drum diameter diameter = 2 cm. %3D %3D 1.8 metres, brake rope %3D |3D Calculate – (i) Indicated power (ii) Brake power

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For a single acting reciprocating pump, piston diameter is 150 mm, stroke length is 300 mm, and rotational speed is 50 r.p.m. The pump is required to lift water to a height of 18 m. Determine the theoretical discharge. If the actual discharge is 4.0 lit./sec, and the mechanical efficiency is 80% determine the volumetric efficiency, slip, theoretical power and the actual power required.
The motorcycles mass: 170 kg The drivers mass: 64 kg I1= 0,26m I2=0,19m a) What is the needed acceleration so the front wheel will lift from ground? b) What is the needed supporting force on the rear wheel (in the cituation above)? c) What is the needed friction force (in the cituation above)? d) What is the friction coeffiecient (in the cituation above)?
If there is no friction between shaft AB and the collar, what angular velocity Ö must the mechanism have to keep the collar at r= 660 mm from the vertical axis? Consider the same mechanism again, with m = 3.3 kg, d = 275 mm, k = 180 N/m, only now, instead of being smooth, the collar and shaft have a maximumcoefficient of friction of 0.74. What is the minimum angular velocity required to keep the collar at a constant distance r= 660 mm from the axis of rotation?
Fluid Mechanics. Reg.no : 5395 Pb # 6: At its optimum point of operation, a given centrifugal pump with an impeller diameter of 500 mm delivers a 4 m3/s of water against a head of (Reg.No/100) m when rotating at 1500 rpm. (a) If its efficiency is 82%, what is the brake power of the drive shaft? (b) If a homologous pump with a diameter of 800 mm is rotating at 1200 rpm, what would be the discharge, head, and shaft power. Assume both operate at the same efficiency. (c) Compute the specific speed of both pumps. What type of pumps are these?
.A steam engine develops power at mean torque of 18,000 N-m and velocity of 9 m/s. The mean diameter of the flywheel rim is 1.3 meters. The coefficient of fluctuation of speed is 0.03 and the coefficient of fluctuation of energy is 0.21. Determine the thickness of the rim in mm if the width of the rim is twice of its thickness. Assume density of rim material as 7250 kg/m3.
1. If there is no friction between shaft AB and the collar, what angular velocity θ˙˙ must the mechanism have to keep the collar at r=300 mm from the vertical axis? Express your answer to three significant figures. 2. Consider the same mechanism again, with m=2.95 kg, d=225 mm, k=250 N/m, only now, instead of being smooth, the collar and shaft have a maximum coefficient of friction of μs=0.297. What is the minimum angular velocity required to keep the collar at a constant distance r=300 mm from the axis of rotation? Express your answer to three significant figures.
Prob # 9. Find the horsepower transmitted by a pair of friction wheels, the diameter of driving wheel is 10 inches, and it revolves at 200 rpm. The width of the wheel is 2 inches. The force per inch width of face is 150 pound and the coefficient of friction is 0.20. a. 96 hp b. 23 hp c. 1.2 hp d. 1.6 hp
A. A motorcycle and rider have a combined mass of 350kg. The wheels each have a mass of 20kg, diameter of 500mm and radius of gyration of 200mm. The rider accelerates uniformly from 5m/s to 25m/s over a distance of 100m, whilst climbing a hill of slope 1 in 20. The average resistance to motion, including drag, is 105 N. 1. Determine the total work done as the motorcycle ascends the incline. 2. Calculate the amount of power developed during the climb. B. At another point in its journey, the motorcycle and rider travel at 80 km/h around a left-hand bend of radius 30m. Calculate: 1. The angular velocity of each of the wheels. 2. The moment of inertia of each wheel. 3. The magnitude and effect of the gyroscopic torque produced on the bike.
Fluid Mechanics. Plz, solve this question completely, i posted it two times but, the solutions were incomplete and non right.Plz, solve it completely, all the parts. Reg.no : 5395 Pb # 6: At its optimum point of operation, a given centrifugal pump with an impeller diameter of 500 mm delivers a 4 m3/s of water against a head of (Reg.No/100) m when rotating at 1500 rpm. (a) If its efficiency is 82%, what is the brake power of the drive shaft? (b) If a homologous pump with a diameter of 800 mm is rotating at 1200 rpm, what would be the discharge, head, and shaft power. Assume both operate at the same efficiency. (c) Compute the specific speed of both pumps. What type of pumps are these?
The torque exerted by a shaft in a Prony brake with an arm length of 1.85-feet and the scale reading of 250-lb of force.
A pump has a displacement of 90 cm3 . It delivers 75 Lpm at 1300 rpm and 75 bar .If the prime mover torque is 90 N-m. What is the theoritical troque required to operate the pump? a. 107.48 N-m b. 75 N-m c. 120.54 N-m d. 90 N-m
Determine the time required to stop a Car weighing 1000 kg, moving at a velocity of 120 km/hr, provided with a braking system, develops a pressure of 10 bar in the brake cylinder, with a diameter of 25 cm.