A plate is used as a tension member, to carry a deadload = 300 KN and live load of 260 KN. Steel used is A36, F, = 248 MPa, Fu = 400 MPa. If the width of the tension plate is 210 mm, determine: a) The thickness of the plate based on NSCP 2015 ASD, bult used is M20.------ b) The thickness of plate based on NSCP 2015 LRFD. Bolt used is M20.-------- 210 mm M20 bolts- -Tension Plate

A plate is used as a tension member, to carry a deadload = 300 KN and live load of 260 KN. Steel used is A36, F, = 248 MPa, Fu = 400 MPa. If the width of the tension plate is 210 mm, determine: a) The thickness of the plate based on NSCP 2015 ASD, bult used is M20.------ b) The thickness of plate based on NSCP 2015 LRFD. Bolt used is M20.-------- 210 mm M20 bolts- -Tension Plate

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.5.2P

See similar textbooks

Similar questions

The given beam is laterally supported at the ends and at the 1 3 points (points 1, 2, 3, and 4). The concentrated load is a service live load. Use Fy=50 ksi and select a W-shape. Do not check deflections. a. Use LRFD. b. Use ASD.
The member shown in Figure P6.6-4 is part of a braced frame. The load and moments are computed from service loads, and bending is about the x axis (the end shears are not shown). The frame analysis was performed consistent with the effective length method, so the flexural rigidity. EI, was unreduced. Use Kx=0.9. The load and moments are 30 dead load and 70 live load. Determine whether this member satisfies the appropriate AISC interaction equation. a. Use LRFD. b. Use ASD.
The tension member shown is a C12 x 20.7 of A572 grade 50 steel. Will it safely support a service dead load of 60 kips and a service live load of 125 kips? Use eq. 3.1 for U.
A double channel shape is used as a tension member. The channels are bolted to a gusset plate with 22mm diameter bolts. Fy-channel = 345 MPa, Fu-channel = 450 MPa Fy-plate = 248 MPa, Fu-plate = 400 MPa Achannel = 3555 mm^2, tw = 12.18 mm, Shear lag factor = 0.90 A. Determine the ultimate tensile strength of the tension member based on its gross area.
An unsymmetrical flexural member consists of a ½ × 12 top flange, a ½ × 7 bottom flange, and a ⅜ × 16 web. a. Determine the distance y from the top of the shape to the horizontal plastic neutral axis. b. If A572 Grade 50 steel is used, what is the plastic moment M, for the horizontal plastic neutral axis? c. Compute the plastic section modulus Z with respect to the minor principal axis. Pls help!
Select a rectangular (not square) HSS for use as a 15-foot-long compression member that must resist a service dead load of 35 kips and a service live load of 80 kips. The member will be pinned at each end, with additional support in the weak direction at midheight. Use A500 Grade C steel. a. Use LRFD. b. Use ASD
A bolted lap joint is used to connect a rectangular bar to a hanger bracket, as shown in Fig. P2.8-2. If the allowable shear stress in the bolt is 80 MPa, and the diameter of the bolt shank 15 mm, what is the allowable tensile load on the rectangular bar, Pallow., in kN?
Given the following allowable stresses:• 50 MPa for shear in rivets• 100 MPa for bearing between a plate and a rivet• 80 MPa for tension in the platesNOTE: Draw FBD(a) If we increase the diameter of each bar to 20 mm, determine the maximum load Pthat can be applied to the lap joint.(b) Using the value computed for maximum load P from (a) compute for the over-allfactor of safety given that the actual P= 20kN.
A W16x45 (A992 steel) (see below) is used in tension and connected to a plate on each flange. Determine the nominal strength based on the effective area (Ae) two ways: First, use the usual shear lag factor equation U = 1 –(?̅/L). Next use the alternative ‘U’ value from AISC Table D3.1.
Steel design. The lap joint shown consist of bolts 22mm in diameter in 25mm diameter holes, The plates are A36 steel with Fy=250MPa, and Fu=400MPa. Use x1=50 mm ,x2= 160mm ,x3=60mm and plate thickness t=12mm for this problem. The allowable stress are: Bearing stress on project are,Fc=1.5Fu Tension on the net area of plates,Ft=0.5Fu Shear on the plates, Fv=0.3Fu Shear strength of bolt,Fv=210MPa Det. the value of Load P based on bolt shear Det. the value of Load P base on bearing on projected area on plate. Det. the value of load P based on block shear