Problem 1A 2.1-MW Sulon S97 wind turbine has a cut-in wind speed uc = 3.5 m/s, rated wind speed u, = 11 m/s and afurling wind speed of uf = 20 m/s. If this machine is located in Rayleigh winds with an average wind speed of7 m/s, find the following:a)How many hours per year is the wind below the cut-in wind speed?b)How many hours per year will the turbine be shut down due to excessive winds?How many kWh/yr will be generated when the machine is running at rated power?c)

Answered: Problem 1 A 2.1-MW Sulon S97 wind…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter11: Transient Stability

Section: Chapter Questions

Problem 11.3P

See similar textbooks

Similar questions

For the power system of Figure Q4.1, all per unit quantities have been calculated using a common base. The generator delivers power ??∞=1 ??.??. at a lagging power factor of ????????=0.93. i) Calculate the internal voltage of the generator, the maximum electrical power that the generator can deliver to the system during the steady state operation and the steady state rotor angle, ??0, of the generator.ii)A three-phase fault occurs at busbar 3 and it is cleared by simultaneously disconnecting lines 13 and 23. Following the fault clearing, the system continues to operate with only line 12 in service. Determine the new steady state rotor angle, ??1, of the generator and the maximum power the generator can deliver to the system post fault.iii)Assuming that the post fault condition is small disturbance stable and that there is no negative interaction among system controllers, calculate the critical clearing angle, ??????, at which the fault should be cleared to ensure the generator reaches…
The flux density distribution in the airgap of a 60Hz,4-pole, salient pole machine is sinusoidal, having an amplitude of 0.8 T. Calculate the instantaneous and rms values of the voltage induced in 1150-turn, If the axial length of the armature and its inner diameter are both 100 mm.
Static load flow equation aretype of equations.O QuadraticO Non LinearO RationalO Linear
A power plant comprises three turbine-generators rated 1000 MW, 800 MW and 600 MW respectively. The regulation constant of each generator is 0.05 pu based on its own rating. Each unit is initially operating at one-half of its own rating, when the system load suddenly increases by 250 MW. Calculate the following:a) Per-unit area frequency response characteristic on a 1000 MW system base [CR9]b) Steady-state drop in area frequency [CR4]c) The share of the load increase on each generator [CR9]d) Total load on each generator after the increase in system load [CR3]Assume the reference power setting of each turbine is unchanged.
Show that an alternator running in parallel on constant-voltage and frequency bus-bars has a natural time period of oscillation. Deduce a formula for the time of one complete oscillation and calculate its value for a 5000-kVA, 3-phase, 10,000-V machine running at 1500 r.p.m. on constant 50-Hz bus-bars. The moment of inertia of the whole moving system is 14,112 kg-m2 and the steady short-circuit is five times the normal full-load value. ANSWER IS [1.33 second]
How many poles should a 60-Hz generator have, if it is connected to a turbine operating undera design head of 3000 ft with a flow of 82 cubic feet per second? Assume turbine specific speedand efficiency of 3 rpm and 84% respectively.
111/ The armature reaction of the DC generator reduces the generated EMF. Select one: True False
Q2)A. Explain compound DC generator, also describe its types and terminal characteristics of compound DC generator. proper explanation and diagram
A DC shunt generator supplies a load of 27 kW at 210 V through the cables of resistance, R = 126 mΩ. If the field winding resistance, Rf = 62 Ω and the armature resistance, Ra = 35 mΩ, Determine (a) the terminal voltage, and (b) the E.m.f. generated in the armature. The terminal voltage is = The E.m.f generated in armature is =
A 2000V 3-phase 4-pole wye connected SM runs at 1800 rpm. The excitation is constant and gives an emf per phase of 1150V. The resistance is negligible compared to synchronous reactance of 3Ω/ . Determine the following when the armature current is 200A. a. Input power per phase b. Torque develop per phase
A lap wound dc generator having 50slots with 15conductors per slot generated at no led emf of 400v when running at 1000 rpm suppose if the same generator is desired to genate 220v on open circuit. Suggest the speed at which it has to be rotated
A 3 phase 4MVA, 12 kV star connected synchronous generator has Zs= 0.8+J30 ohm. Using circle diagram only, find: 1. The output power developed at unity power factor with excitation equal to 1.25 of rated voltage. 2. The load angle and power factor if the generator supplies (1500 KW) at rated voltage and excitation lequal to (1.2) of rated voltage. 3. Repeat part (2) when .armature resistance is neglected

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning