Problem 1The reel has a mass of 30 kg and a radius of gyration about A of KA = 120 mm. Thesuspended cylinder has a mass of 40 kg. Starting from rest, the motor M exerts aconstant force of P = 300 N on the cable.Determine the mass moment of inertia of the reel.Determine the velocity of the cylinder after it has traveled upward 2 m.Determine the time that was taken to travel the 2 m distance.150 mmP = 300 N75 mm

(a) The mass moment of the inertia of the reel can be calculated as

Answered: Problem 1 The reel has a mass of 30 kg…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The object consists of an 8 lb thin bar welded to a 12 lb disk. It is released from rest at horizontal position 1 and falls to position 2. Identify the center of mass of the object and the moment of inertia with respect to the center of mass. of inertia with respect to center of mass
cable is wrapped around the spool’s center hub. The mass of the spool is m= 100 kg, the radius r1 = 0.4 m, r2 =0.6 m, and the radius of gyration is kG = 0.3 m. A horizontal force P = 10 N is applied to the cord. The spool is initially at rest and rolls without slipping. (2) The mass moment of inertia of the spool about point A _______(kg·m2)(two decimal places)
In the helicopter shown; a vertical tail propeller is used to pre- vent rotation of the cab as the speed of the main blades is changed. Assuming that the tail propeller is not operating determine the final angular velocity of the cab after the speed of the main blades has been changed from I80 to 240 rpm. (The speed of the main blades is measured relative to the cab, and the cab has a centroidal moment of inertia of 650 lb.ft.s2. Each of the four main blades is assumed to be a slender rod 14 ft weighing 55 lb.)
A cable is wrapped around the spool’s center hub. The mass of the spool is m= 100 kg, the radius r1 = 0.4 m, r2 =0.6 m, and the radius of gyration is kG = 0.3 m. A horizontal force P = 10 N is applied to the cord. The spool is initially at rest and rolls without slipping. (2) The mass moment of inertia about point A _______(kg·m2)(two decimal places)
In order to determine the mass moment of inertia of a flywheel of radius 600 mm, a 12-kg block is attached to a wire that is wrapped around the flywheel. The block is released and is observed to fall 3 m in 4.6 s. To eliminate bearing friction from the computation, a second block of mass 24 kg is used and is observed to fall 3 m in 3.1 s. Assuming that the moment of the couple due to friction remains constant, determine the mass moment of inertia of the flywheel.
The passengers, the ship and the structure have a total mass of 73 Tons, their center of mass in G, and a radius of gyration with respect to B of kB = 3.5 m. Additionally, the 3-ton steel block at point A can be considered as a point of concentrated mass. If the ship rotates freely at 9.3 rad/s when it reaches the lowest point, as shown in the figure, determine the moment of inertia of the system about pivot B (in kgm2) The angular acceleration for the position shown (in rad/s2) is: The vertical reaction at pivot B (in N) is: The horizontal reaction at pivot B (in N) is:
Each paddle wheel of a steamer have a mass of 1600 kg and a radius of gyration of 1.2 meters. The steamer turns to port in a circle of 160 meters radius at 24 km/hr. The speed of the paddle is 90 rpm. Determine the magnitude and effect of the gyroscopic couple acting on the steamer.
3.32). As shown in Figure 3, a yo-yo toy is formed by wrapping a massless cord around adisk of radius R= 0.2 m and mass M=3 kg. The cord is vertical and its top end is fixed and the disk isinitially stationary. The cord remains vertical for the entire motion and does not slide on the disk.When the disk is released from rest, it falls down by a distance H=0.8 m, The moment of inertia ofthe disk around its center is I disk=1/2mdiskR^2a . Find the angular acceleration of the disk when it is lowered by a distance H.b . Find the angular velocity of the disk when it is lowered by a distance H.
A cylinder shown has a weight of 100lb Assuming the cylinder to be solid indetermining the moment of inertiaa.Determine the velocity of the cylinder after it has rolled 10ft from restif the horizontal force P applied at A is 10lbb.Determine the velocity of the cylinder after it has rolled 10 ft fromrest if the horizontal force P=10lb is applied at Bc.Determine the velocity of the cylinder after it has rolled 10 ft fromrest if the horizontal force P=10lb is applied at C
A cylinder shown has a weight of 100lb Assuming the cylinder to be solid indetermining the moment of inertiaa.Determine the velocity of the cylinder after it has rolled 10ft from restif the horizontal force P applied at A is 10lbb.Determine the velocity of the cylinder after it has rolled 10 ft fromrest if the horizontal force P=10lb is applied at Bc.Determine the velocity of the cylinder after it has rolled 10 ft fromrest if the horizontal force P=10lb is applied at
A stepped cylinder has the dimensions R₁ = 0.30 m, R₂ = 0.65 m, and the radius of gyration, k, is 0.35 m. The mass of the stepped cylinder is 100 kg. Weights A and B are connected to the cylinder. If weight B has a mass of 80 kg, and weight A has a mass of 50 kg, how far does A move in 5 seconds? In which direction does it move? (Draw all FBDs)
The thin rod of the figure has a mass of 15kg and is attached to a spring of constant K = 50 N/m at one end, which has an unstretched length of 1.5 m. If the rod is released from rest in horizontal position (ø = 0°) and only conservative forces act on it, determine: a) What is the moment of inertia of the thin rod around the axis of rotation in A? b) What is the angle at which the rod is momentarily resting again? c) What is the maximum angular speed of the route? Please attach the free body diagram if necessary. Thank you!

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS