4) The plug has a diameter of 30 mm and fits within a rigid sleeve having an inner diameter of 32 mm as shown in the figure. The material has E = 5 MPa and v= 0.45. Determine the axial pressure that must be applied to the top of the plug to cause it to contact the sides of the sleeve. Answer: 32mm 30mm 50mm

4) The plug has a diameter of 30 mm and fits within a rigid sleeve having an inner diameter of 32 mm as shown in the figure. The material has E = 5 MPa and v= 0.45. Determine the axial pressure that must be applied to the top of the plug to cause it to contact the sides of the sleeve. Answer: 32mm 30mm 50mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cylindrical steel tank is manufactured based on the following data:internal pressure: 2460 psifactor of safety with respect to YP: 2.0yield stress in tension (circumferential): 56 000 psiyield stress in shear (longitudinal): 22 000 psi(a) Determine the minimum wall thickness if the diameter of the cylindrical steel tank is 7 inches.(b) Determine the maximum acceptable internal pressure if the wall thickness is 0.50 inches.Use 2 decimal places in every solved values. (25 pts)
It is necessary to deliver 21.2 cfs to point D in the figure below at a pressure of 40 psi. Determine the pressure at A in psi. The answer should be 45.8 psi. Show free body diagram
A square plastic bar (length Lp, side dimension sp = 193 mm) is inserted inside a hollow, square, cast iron tube (length Lc = 400 mm, side sc = 200 mm, and thickness tc = 3mm). (a) What is the required initial length Lp of the plastic bar so that, when it is compressed by some force P, the final length of bar and tube are equal to legnth Lc, and, at the same time, the gap between plastic bar and cast iron tube is closed? (b) Compare initial and final volumes for the plastic bar. Assume that Ec = 170 GPa, Ep = 2.1 GPa, vc = 0.3, and vp = 0.4.
The plug has a diameter of 30 mm and fits within a rigid sleeve having an inner diameter of 32 mm. Both the plug and the sleeve are 50 mm long. Determine the axial pressure p that must be applied to the top of the plug tocause it to contact the sides of the sleeve. Also, how far must the plug be compressed downward in order to do this? The plug is made from a material for which E = 5 MPa, n = 0.45.
a.) Find the bulk modulus of elasticity of a liquid if a pressure of 150 psi applied to 10 ft3 of the liquid causes a volume reduction of 0.02 ft.3. b.) Find the capillary rise in the tube for a water-air-glass interface (θ = 0°) if the tube radius is 1 mm. Surface tension is 0.0728 N/m.
3) Solve the following problem: The hollow tube ABCDE is made of a material that is subjected to five torsores that act as shown in the figure below. The outside diameter of the tube is d2 = 1.0 inches. The maximum allowable shear stress is 12,000 psi (12,000 lb / inch ^ 2). In addition, the maximum rotation per foot allowed is 2.0 degrees (2.0 degrees / foot). Take G = 9500 Ksi (9,500,000 psi). Note: Remember that 1 degree equals 0.0175 radians. Determine the maximum internal diameter d1, allowed for the tube.
Determine the magnitude of intensity q that will produce a fully plastic condition in the beam shown below (refer to figure). The beam is made of steel with yield stress = 108 ksi and has rectangular cross section as shown. (Hint: a sliding support prevents rotation but allows vertical displacement . Express your answer in lbs/inch, up to 1 decimal place)
Part 2Two pipes are connected by a manometer as shown. Determine the pressure difference, between the pipes in kPa.
The pressure in tank is 2.99atm .Determine the gauge pressure.
A thin cylinder 200mm internal diameter, 3mm thick has its ends closed with rigid plates. The cylinder is then filled with water. When an external axial pull of 60KN is applied to the ends then the water pressure is observed to fall by 0.1N/mm2.Determine the value of Poisson’s ratio. Take E = 170,000N/mm2, K=2000N/mm2.
A line load of q=60kn/m with alpha =300 is placed on a ground surface as shown in figure p4.1.Calculate the increase of pore water pressure at M immediately after application of the load for the cases given below. (a) z=10m ,X=0m ,v=0.5 ,A=0.45 (b) z=10m, X=2m,v=0.45, A=0.6
A steel column of hollow circular cross section is supported on a circular, steel base plate and a concrete pedestal (see figure). The column has an outside diameter d = 250 mm and supports a load P - 750 kN. (a) If the allowable stress in the column is 55 MPa, what is the minimum required thickness? Based upon your result, select a thickness for the column, (Select a thickness that is an even integer, such as 10, 1 14,.. ., in units of millimeters.) (b) If the allowable bearing stress on the concrete pedestal is 15 MPa, what is the minimum required diameter D of the base plate if it is designed for the allowable load Pallow that the column with the selected thickness can support.