Problem 1. A balanced delta connected load of 15 + j18 Q per phase is connected at the end of a three-phase line as shown in the below figure. The line impedance is 1+ j2 N per phase. The line is suppliedfrom a three-phase source with a line-to-line voltage of 207.85 V (rms).1+ j2 Nwwma|VL|= 207.85 Vbo15+ j18 NTaking Vm as reference, determine the following:a) Current in phase a;b) Total complex power supplied from the source;c) Magnitude of the line-to-line voltage at the load terminal;d) The actual load current.Hint: Convert equivalently delta to wye connection.

In the question, 3 phase balance supplied to 3 phase balance delta load Find the line current,…

Problem 1. A balanced delta connected load of 15 +j18 2 per phase is connected at the end of a three- phase line as shown in the below figure. The line impedance is 1 + j2 2 per phase. The line is supplied from a three-phase source with a line-to-line voltage of 207.85 V (rms). 1+ j2 N |VL] = 207.85V bo 15 + j18 N www www Taking Vm as reference, determine the following: a) Current in phase a; b) Total complex power supplied from the source; c) Magnitude of the line-to-line voltage at the load terminal; d) The actual load current. Hint: Convert equivalently delta to wye connection.

Problem 1. A balanced delta connected load of 15 +j18 2 per phase is connected at the end of a three- phase line as shown in the below figure. The line impedance is 1 + j2 2 per phase. The line is supplied from a three-phase source with a line-to-line voltage of 207.85 V (rms). 1+ j2 N |VL] = 207.85V bo 15 + j18 N www www Taking Vm as reference, determine the following: a) Current in phase a; b) Total complex power supplied from the source; c) Magnitude of the line-to-line voltage at the load terminal; d) The actual load current. Hint: Convert equivalently delta to wye connection.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.44P: Two balanced three-phase loads that are connected in parallel are fed by a three-phase line having a...

See similar textbooks

Similar questions

Two balanced three-phase loads that are connected in parallel are fed by a three-phase line having a series impedance of (0.4j2.7) per phase. One of the loads absorbs 560 kVA at 0.707 power factor lagging, and the other 132 kW at unity power factor. The line-to-line voltage at the load end of the line is 2203V. Compute (a) the line-to-line voltage at the source end of the line. (b) the total real and reactive power losses in the three-phase line, and (c) the total three-phase real and reactive power supplied at the sending end of the line. Check that the total three-phase complex power delivered by the source equals the total three-phase comp lex power absorbed by the line and loads.
Two three-phase generators supply a three-phase load through separate three-phase lines. The load absorbs 30 kW at 0.8 power factor lagging. The line impedance is (1.4+j1.6) per phase between generator G1 and the load, and (0.8+j1) per phase between generator G2 and the load. If generator G1 supplies 15 kW at 0.8 poir factor lagging, with a terminal voltage of 460 V line-to-line, determine (a) the voltage at the load terminals. (b) the voltage at the terminals of generator G2, and (c) the real and reactive power supplied by generator G2. Assume balanced operation.
A 3-phase Y-connected load draws power from a 3-phase Y-connected source. The source voltage, ?=440∠0º?_rms and the load impedance, Z_y=(30+j15) Ω. The line impedance, Z_line= (1+j1)Ω and the system operates at 60 Hz. a) Draw the single-phase equivalent circuit and label all given quantities numerically. b) Calculatethe rms line (phase) current phasor in each phase. c) Calculate the total active or real power supplied by the source. d) Calculate the total active or real power consumed by the load. e) Calculate the total line loss i.e. the total activepower lost due to line. f) Determine the power efficiency of the system.
A 4200-V, three-phase transmission line has an impedance of 4+j ohms per phase. If it supplies a load of 1 MVA at 0.75 power factor, find: (a) the complex power (b) the power loss in the line (c) the voltage at the sending end. *Ans. S=0.75+j0.66 MVA, PL=25.14 kW and VS=4.492∠ − 1.912°kV Use four decimal places.
A 3-phase Y-connected load draws power from a 3-phase Y-connected source. The source voltage, ?=440∠0º?_rms and the load impedance, Z_y=(30+j15) Ω. The line impedance, Z_line= (1+j1)Ω and the system operates at 60 Hz. d) Calculate the total active or real power consumed by the load. e) Calculate the total line loss i.e. the total activepower lost due to line. f) Determine the power efficiency of the system.
A balanced delta connected load of "14+j19" 2- per phase is connected at the end of a three-phase line. The line impedance is "6+18j" 2- per phase. The line is supplied from a three-phase source with a line-to-line voltage of 207.85 Vrms. Taking phase "a" voltage Va as reference, determine the following: (a) Current in phase a. (b) Total complex power supplied from the source. (c) Magnitude of the line-to-line voltage at the load terminal.
A balanced delta connected load of 13+j16 ohm per phase is connected at the end of a three-phase line. The line impedance is 2+j11 ohm- per phase. The line is supplied from a three-phase source with a line-to-line voltage of 207.85 Vrms. Taking phase "a" voltage Va as reference, determine the following: (a) Current in phase a. (b) Total complex power supplied from the source. (c) Magnitude of the line-to-line voltage at the load terminal.
A three-phase line feeds two balanced three-phase loads connected in parallel. The first Y load consumes a total of 630,000 W at 0.6 power factor lagging. The second in Δ it has an impedance per phase of 46.08 – j 13.44 Ω. The line-to-line voltage at the end of the loads corresponds to 6920 Vrms, negative sequence. Find the total line current and power total complex absorbed by the two-charge system.
Two balanced loads are connected to a 240-kV rms 50-Hz line. Load 1 draws 30 kW at a power factor of 0.6 lagging, while load 2 draws 45 kVAr at a power factor of 0.8 lagging. Assuming the RYB sequence, determine: (a) the complex, real, and reactive powers absorbed by the combined load, (b) the line currents, and (c) the kVAr rating of the three capacitors ∆-connected in parallel with the load that will raise the power factor to 0.9 lagging and the capacitance of each capacitor. Verify the results by creating a MATLAB Simulink model and program. Obtain the plots for the currents and voltages
A balanced three-phase source furnishes power to the following three loads:Load 1: 6 kVA at 0.83 power factor laggingLoad 2: unknownLoad 3: 8 kW at 0.7071 power factor leadingIf the line current is 84.6 A rms, the line voltage at the load is 208 V rms, and the combined loadhas a 0.8 power factor lagging, determine the unknown load.
In a balanced 3-phase system, the effective value of the IbB current for a triangular connected load is known as 15 (-150 degrees) Amperes and the effective value of the VCA voltage is known as 60 (90 degrees) Volts. Since it is known that the phase sequence is positive; Phase current IAB= 8.660 (60 degrees) A Phase current IAC= [Select ] Load impedance Z= [Select ] the total average power sent to the 3 phase load is Pt Aggregate= [Select ] (Note: Perform your operations using at least 3 digits after the comma.)
A load of 135 MW at a power factor of 0.6 lagging can be delivered by a 3-phase transmission line. The voltage at the receiving end is to be maintained at 57 kV and the loss in the transmission is 6.5% of the power delivered. (Consider the line to be a short transmission line) Find A) Single phase Power delivered B) Per phase voltage C) Current flowing through the transmission line D) 3 Phase Losses in the transmission line E) Per phase resistance of the transmission line