Problem 10 B (15.0 m) D(10.0 m) 30.0 53.0 25.0 Č 12.0 m) Ä (8.00 m) Part a Compute the x- and y-components of the vectors A, B, C, and Ď. Part b Use the method of components to find the magnitude and direction (angle measured counterclockwise from x-axis) of: i) A + B ii) A - B iii) B – À Part c Find the scalar products: i) A · B ii) B.T iii) A . T Part d Find the magnitude and direction of the following vector products: i) A × D ii) D × À

Problem 10 B (15.0 m) D(10.0 m) 30.0 53.0 25.0 Č 12.0 m) Ä (8.00 m) Part a Compute the x- and y-components of the vectors A, B, C, and Ď. Part b Use the method of components to find the magnitude and direction (angle measured counterclockwise from x-axis) of: i) A + B ii) A - B iii) B – À Part c Find the scalar products: i) A · B ii) B.T iii) A . T Part d Find the magnitude and direction of the following vector products: i) A × D ii) D × À

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.12P: A differential equation encountered in the vibration of beams is d4ydx4=2D where x = distance...

See similar textbooks

Similar questions

1. An architect wants to build a wall with the profile shown. To estimate the effects of wind loads, he must determine the wall’s area and the coordinates of its centroid. Determine the x coordinate of the centroid of the area. 2. An architect wants to build a wall with the profile shown. To estimate the effects of wind loads, he must determine the wall’s area and the coordinates of its centroid. Determine the y coordinate of the centroid of the area.
Find the resultant and angle of direction based on the horizontal. using tail to tip method A) 25 lb. 40 0N of E B) 10 lb 45 0N of W
Find the resultant and angle of direction based on the horizontal. using tail to tip method 1. 20 lb 45 oN of E 2. 35 lb 20 oN of W
Beam AB is subjected to a triangular load as shown below. Determine the resultant and its distance from A.
A centroid is an object's geometric center. For an object of uniform composition, its centroid is also its center of mass. Often the centroid of a complex composite body is found by, first, cutting the body into regular shaped segments, and then by calculating the weighted average of the segments' centroids.An object is made from a uniform piece of sheet metal. The object has dimensions of a = 1.05 ft , where a is the diameter of the semi-circle,b = 3.74 ft , and c = 2.45 ft . A hole with diameter d = 0.700 ft is centered at (0.925,0.525) . Part A Find the area of the body. (Figure 1) Express your answer numerically in feet squared to three significant figures. Part B Find x¯ , the x -coordinate of the body's centroid. (Figure 1) Express your answer numerically in feet to three significant figures. Part C Find y¯ , the y -coordinate of the body's centroid. (Figure 1) Express your answer numerically in feet to three significant figures.
n this question, you will calculate the second moment of area for a 4 ✕ 6 piece of lumber about the x − x and y − y axes, as shown. A rectangle with height h and width w > h is centered on the origin of the x y-coordinate plane. The left and right sides of the rectangle, having height h, are parallel to the vertical y – y axis and the top and bottom sides, having width w, are parallel to the horizontal x – x axis. Visit a hardware store and measure the actual dimensions of a typical 4 ✕ 6 piece of lumber. (Enter your answers in inches.) h = in w = in Calculate the second moment of area about the x − x and y − y axes using the measured dimensions. (Enter your answers in in.4.) Ix – x = ______in4 Iy – y = ________in4
The length of the ship’s water-plane area is 70 m. The lengths of the equidistantly spaced half ordinates commencing from forward are as follows: 0, 5.2, 6.4, 7.0, 6.0, 4.9, 0.3. Find the area of the water-plane.
Solve using scalar components, not vector components.
Here use integration method to find a) the area of the shaded region b) coordinates of the centroid of the plane region shown
Figure (a) shows the cross section of a column that uses a structural shape known as W867 (wide-flange beam, nominally 8 in. deep, weighing 67 lb/ft). The American Institute of Steel Construction Structural Steel Handbook lists the following cross-sectional properties: A=19.7in.2,Ix=272in.4, and Iy=88.6in.4. Determine the dimensions of the rectangle in Fig. (b) that has the same Ix and Iy as a W867 section.
Verify the centroidal z-coordinate of the pyramid shown in Table 8.3 by integration.
A differential equation encountered in the vibration of beams is d4ydx4=2D where x = distance measured along the beam; [x]=[L] y = displacement of the beam; [y]=[L] = circular frequency of vibration; []=[T1] = mass of the beam per unit length; []=[ML1] D = bending rigidity of beam; [D]=[FL2] Show that the equation is dimensionally homogeneous. Note that [F]=[MLT2] see Eq. (1.21:).