Problem # 2: The plate shown is fastened to the fixed member by eight 16-mm diameter rivets. Compute the polar moment of inertia, J. Determine the value of the loads P so that the maximum shearing stress in any rivet does not exceed 80 MPa. If P = = 8200 N, what is the maximum and minimum shearing stress developed in the rivet ) 148 mm 115 mm O 82 mm 25 mm 42 mm 56 mm 68 mm 47 mm

Problem # 2: The plate shown is fastened to the fixed member by eight 16-mm diameter rivets. Compute the polar moment of inertia, J. Determine the value of the loads P so that the maximum shearing stress in any rivet does not exceed 80 MPa. If P = = 8200 N, what is the maximum and minimum shearing stress developed in the rivet ) 148 mm 115 mm O 82 mm 25 mm 42 mm 56 mm 68 mm 47 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a. Determine the location of the shear center for the following section. b. Determine the shear stress at point A, if a 20kN (downwards) shear load is applied at the shear center. Given: h1= 25mm h = 100mm b = 50mm Thickness = 4mm
The plate shown in the figure is fastened to the fix member by three 10 mm diameter rivets. Compute the value of the loads P so that the shearing stress of any rivet does not exceed 70 Mpa.
Assume that the axial load P = 40kN applied to the lap joint is distributed equallyamong the three rivets. What is the smallest diameterof the rivetif the allowable stresses are 90 MPa for bearing between a plate and a rivet, and 40MPa for shear in rivets?
Six 20mm diameter rivets fasten the plate, as shown, to the fixed member. Determine the average shearing stress caused in each rivet by the P (in kilo-newton) loads. P=74 Show detailed solution
•Timber beamSafe working stress = 25 MPaCross-section dimensions:height = 119 mm,width = 66 mmProving ring number 293. Steel beam Safe working stress = 200 MPa Cross-section dimensions:external height = 149 mm,external width = 50 mm,wall thickness = 3.0 mm,Proving ring number 1522.1)Calculate safe max bending moment in the central part of the beam using Mmax = (I)(max stress)/(D/2)2) calculate Safe applied force in the proving ring or tie rod, assuming a symmetrical setup as in the photowith a ‘lever arm’ of 600 mm
A post having a hollow, circular cross sectionsupports a P = 3.2 kN load acting at the end of an armthat is b =1.5 m long (see figure). The height of thepost is L = 9 m, and its section modulus is S = 2.65x105 mm3. Assume that the outer radius of the post isr2 =123 mm, and the inner radius is r1 =117 mm.(a) Calculate the maximum tensile stress σmax andmaximum in-plane shear stress τmax at point A onthe outer surface of the post along the x axis dueto the load P. Load P acts at B along line BC.(b) If the maximum tensile stress and maximumin-plane shear stress at point A are limited to90 MPa and 38 MPa, respectively, what is thelargest permissible value of the load P?
The steel shaft with two different diameters rotates at 4.2 Hz. The power supplied to gear C is 68 kW, of which 42 kW is removed by gear B. Find the maximum shear stress (in Pa) in the shaft if d = 58.1 mm, h = 60.6 mm, L = 3.9 m, M = 2.1 m, and G = 83.49 Gpa. Round off the final answer to two decimal places
The lap joint shown is fastened by 6 − 20mm diameter rivets. Assuming that ? = 200??, determine (a) the shearing stress in each rivet, (b) the bearing stress in each plate 25mm thick and 100mm wide. Assume that the axial load ? is distributed equally among the 6 rivets, and the diameter of hole is 22mm.
The rigid bar AD is supported by two steel wires of 1.5 mm diameter (E = 200 GPa) and a pinand bracket at D. Knowing that the wires were initially taut, determine the stress in each wirewhen a 1200 N load P is applied at D. What is the corresponding deflection of point D?
A beam has a uniform dead load and live load has a fixed support at both ends. If the beam properties are given below, what is the stress at bottom of the beam section at the midspan. (MPa) Properties: Beam width = 270 mmBeam height = 375 mmWLL = 14.38 kN/mWDL = 18.41 kN/mSpan of the beam = 8 mPrestressing force = 481 kNeccentricity = 103 mm
If P=13000 N, d=22mm and t=33mm, determine the bearing stress between the rivets and plate, in MPa?
The standard length of a tape is 100m having a weight of 1.2kg with the standardtemperature of 20 C and standard pull of 5.5kg. The young modulus of elasticity of thetape is 200GPa, cross sectional area is 2.8mm? and the coefficient of linear expansionis 0.0000116/°C. Determine the normal tension of the tape.