Problem 20.2 A certain point on the surface of a body experiences &x= -175μ, &y=-350µ, Yxy = -500μ where the z- direction is perpendicular to the surface. The material which makes up the body has a Poisson's ratio of v = 0.25 and a Young's modulus of E=30000 ksi. Determine the principal strains and the maximum shearing strain at the point. Determine the principal strain directions. Draw a sketch showing the in-plane principal strain distortions and the maximum shearing strain distortion.

Problem 20.2 A certain point on the surface of a body experiences &x= -175μ, &y=-350µ, Yxy = -500μ where the z- direction is perpendicular to the surface. The material which makes up the body has a Poisson's ratio of v = 0.25 and a Young's modulus of E=30000 ksi. Determine the principal strains and the maximum shearing strain at the point. Determine the principal strain directions. Draw a sketch showing the in-plane principal strain distortions and the maximum shearing strain distortion.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the maximum shearing stress in MPa of a helical spring composed of 18 turns and 25 mm wire diameter on a mean radius of 100 mm when the spring is supporting a load of 1500 N, assume the modulus of rigidity of 83 GPa.
A shaft with a solid circular cross-section is twisted through an angle of Φ = 4.2 degrees. If the diameter of the shaft is 26mm and its length is 2.4m, determine the maximum shearing strain γ . Express your answer in units of microstrain.
Determine the maximum shearing stress in a helical steel spring composed of 20 turns of 20-mm diameter wire on a mean radius of 80 mm when the spring is supporting a load of 2 KN.
PART 2: Determine the shear force acting at each of the following locations: (a) x = 0+ ft (i.e., just to the right of support A) (b) x = 14.0 ft (i,e., at point B.) (c) x = 20.5- ft (i.e., just to the left of the support C) (d) x = 20.5+ ft (i.e., just to the right of the support (C) (e)x=27.5ft Note that x = 0 at support A. When entering your answers, use the shear-force sign convention detailed in Section 7.2. My Answers: Correct (a) V= 105.823 kips (b)V= -48.177 kips (c) V= -119.677 kips (d)V= 88 kips (e) V= 10.9998 kips PART 3: Determine the bending moment acting at each of the following locations: (a) x = 14.0- ft (i.e., just to the left of point B.) (b) x = 14.0+ ft(i.e., just to the right of point B.) (c) x = 20.5 ft (i.e. at point C) (d)x=27.5ft Note that x = 0 at support A. When entering your answers, use the shear-force sign convention detailed in Section 7.2. My Answers: Correct (a) M = 403.522 kips-ft (b) M = 193.522 kips-ft (c) M = -352.0035 kips-ft (d) M =…
The driveshaft of an automobile is being designed to transmit 238 hp at 3790 rpm. Determine the minimum diameter d required for a solid steel shaft if the allowable shear stress in the shaft is not to exceed 5700 psi.
Prove that the sum of the normal strains in perpendicular directions is constant, i.e., P x+ P y = P x + P y.
A thin rectangular plate is uniformly deformed, as shown. Determine the shear strain γxyγx⁢y at P. Assume a = 1200 mm, b = 580 mm, c = 1.3 mm, and d = 1 mm.
A torque of 1.4KNm and two forces of 10kN and 12kN are applied to the top of a 65mm diameter solid steel post. Determine the principal stresses and the maximum shear stress at point H and point K.
A rigid plate of negligible mass rests on the middle spring which is higher than the two outer springs by 20 mm. The middle spring consists of 24 turns of 25-mm diameter wire on a mean diameter of 150 mm. The two outer springs have 16 turns of 12-mm diameter wire on a mean diameter of 100 mm. Determine the shearing stress developed in each spring if P = 5 kN is applied. Use the Approximate formula. Use G = 83 GPa. Answer: τm= 95.39 MPa
PART 1 My answer Ay=14.38 Cy=13.62 Part 2 Determine the shear force acting at each of the following locations: (a) x = 4.25- (i.e., just to the left of point B.) (b) x = 4.25+ (i.e., just to the right of point B.) (c) x = 9.25-(i.e., just to the left of point C) (d) x = 9.25+ (i.e., just to the right of point C) My Answer: (a) V= 14.38 kN (b) V= 14.38 kN (c) V= 14.38 kN (d) V= 28 kN Part 3 Determine the bending-moment acting at each of the following locations: (a) x = 4.25-(i.e.. just to the left of point B.) (b) x = 4.25+ (i.e.. just to the right of point B.) (c) x = 9.25 m (i.e., at support C) (d) x = 8.25 m My Answer: (a) M= 61.115kN-m (b) M= -148.885 kN-m (c) M= -76.985 kN-m (d) M= -91.365 kN-m Part 4: Use your bending-moment diagram to determine the maximum positive bending moment, Mmax, pos, and the maximum negative bending moment, Mmax, neg. Use the bending-moment sign convention detailed in Section 7.2. The maximum negative bending moment is the negative moment with…
A 10 mm diameter specimen of hardened tool steel was tested in double shear and failed under a load of 106.8 kN. If a machine-tool component of square cross-section 12 mm x 12 mm is made from the same material, determine the maximum shear load in single shear allowed if the factor of safety is to be 4.
For the state of stress shown, it is known that the normal and shearing stresses are directed as shown and that σx = 15.5 ksi, σy = 9 ksi, and σmin = 5 ksi. Determine the orientation of the principal planes. Determine the principal stress σmax. Determine the maximum in plane shearing stress