Problem (3): The mass rate of flow into a steam turbine is 1.5 kg/s, and the heat transfer from the turbine is 8.5 kW. The following data are known from the steam entering and leaving the turbine. Inlet Exit Conditions Conditions Pressure 2.0 MPa 0.1 MPa 350°C Temperature Quality Velocity Elevation above reference plane g = 9.8066 m/s² 100% 50 m/s 100 m/s 6 m 3 m Determine the power output of the turbine

Problem (3): The mass rate of flow into a steam turbine is 1.5 kg/s, and the heat transfer from the turbine is 8.5 kW. The following data are known from the steam entering and leaving the turbine. Inlet Exit Conditions Conditions Pressure 2.0 MPa 0.1 MPa 350°C Temperature Quality Velocity Elevation above reference plane g = 9.8066 m/s² 100% 50 m/s 100 m/s 6 m 3 m Determine the power output of the turbine

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

10. The initial design of an IFR turbine is to be based upon Whitfield’s procedure for optimum efficiency. The turbine is to be supplied with 2.2 kg/s of air, a stagnation pressure of 250 kPa, a stagnation temperature of 800°C, and have an output power of 450 kW. At turbine exit the static pressure is 105 kPA. Assuming for air that γ ¼ 1.33 and R ¼ 287 J/kg K, determine the valueof Whitfield’s power ratio, S, and the total-to-static efficiency of the turbine.
The standard Brayton air cycle has a compressor pressure ratio of 10. Air entering the compressor at p1 = 14.7 lbf/in., T1 = 70oF with a mass flow rate of 90,000 lb/hour. The entrance temperature of the turbine is 2200oR. Calculate the thermal efficiency and clean power generated, in horsepower (HP), if.
A turbojet aircraft moving with a velocity of 790 ft/s at a runway where the pressure& temperature is found to be 14.7psi & 546R. The axial flow compressor provides apressure ratio of 14 to 1. Temperature at the turbine inlet is 2000R. The mass flowrate of airinside the engine is 133 lbm/s. Determine the following:a. T-S diagramb. Pressure & temperature at each statec. Thrust force (lbf)d. Propulsive power developed (BTU/min)e. Propulsive Efficiency
Air enters the compressor of a regenerative gas-turbine engine at 100 kPaand 300 K and is compressed to 800 kPa. The regenerator has aneffectiveness of 65 percent, and the air enters the turbine at 1200 K. For acompressor efficiency of 75 percent and a turbine efficiency of 86 percent,determine(a) The heat transfer in the regenerator.(b) The back work ratio.(c) The cycle thermal efficiency
In a single stage impulse turbine the isentropic enthalpy drop of 200 kJ/kg occurs in the nozzlehaving efficiency of 96% and nozzle angle of 15°. The blade velocity coefficient is 0.96 and ratio ofblade speed to steam velocity is 0.5. The steam mass flow rate is 20 kg/s and velocity of steam enteringis 50 m/s. Determine(a) the blade angles at inlet and outlet if the steam enters blades smoothly and leaves axially.(b) the blade efficiency(c) the power developed in kW(d) the axial thrust.Solve using velocity diagram please use the symbols below
Steam expands in a steam turbine isentropically from intet to exhaust having an enthalpy drop=1200 kJ/kg. Assuming ideal conditions determine the mean diameter of wheel if the turbine were of: (1) Single impulse stage. (i) Single 50% reabron stage.
at a stage in a reaction turbine, the mean blade ring diameter is 1 m. the turbine runs at 3000 rpm. the blades are designed for a degree of reaction of 50% with exit angles of 30° and inlet angles of 50°. the turbine is supplied with a steam at 10000 kglh and the stage efficiency is 85%. determine (a) power output of the stage, (b) specific enthalpy drop in kj/kg, (c) percentage increase in relative velocity of steam over moving blades, (d) the specific steam consumption
Kumargaon Power Plant operates, at the thermal efficiency equal to 88% of the Shahbazpur Power Plant, with the steam inlet temperature at 898 0C and subsequently discards the exhaust steam at 150 0C. Note that Shahbazpur Power Plant’s thermal efficiency is equal to 55% of the Carnot Engine’s thermal efficiency for the same temperature. i) What is the current thermal efficiency of the Kumargaon Power Plant? ii) If the thermal efficiency of the Kumargaon Power Plant has to be augmented by 5%, what would be your recommendations to improve the efficiency of the power plant? Why? iii) If environmental regulatory authority restricts the effluent’s discharge temperature between 15 0C and 45 0C, what would you recommend to optimize the waste heat?
Draw a neat diagram of a regenerative gas turbine and reheater and also explain it working with a help of a P-V diagram?
What is the reaction equation of an impulse turbine?
A turbojet-powered aircraft is flying at 220 m/s and 8000-m altitude, where the ambient temperature and pressure are 236K and 35kPa, respectively.The pressure ratio of the compressor is 6 and the turbine inlet temperaturer is 970k. Estimate the thrust developed by the engine when the air flow rate is 55kg/s. employ an air standard-cycle analysis using the constant-pressurree specific heat c_p and specific heat ratio γ for air and neglecting the fuel properties.
Pls. answer thank you! The following performance data were generated by a gas turbine having intercooling: LP compressor inlet conditions of 14.7 psia and 520’’R: LP compressor isentropic discharge temperature, 743.8 R. compressor isentropic efficiency. 78 percent; HP.compressor inlet temperature, S20 degree R: HP compressor isentropic discharge temperature, 743.8 R. HP compressor isentropic efficiency, 82%; turbine inlet temperature, 2000R; and turbine isentropic efficiency, 90%, Calculate the net cycle work Btu/lb.