Problem 4 A 50 wt% Ni-50 wt% Cu alloy is slowly cooled from 1400°C (2550°F) to 1200°C (2190°F). (a) At what temperature does the first solid phase form? (b) What is the composition of this solid phase? (c) At what temperature does the liquid solidify? (d) What is the composition of this last remaining liquid phase?

Problem 4 A 50 wt% Ni-50 wt% Cu alloy is slowly cooled from 1400°C (2550°F) to 1200°C (2190°F). (a) At what temperature does the first solid phase form? (b) What is the composition of this solid phase? (c) At what temperature does the liquid solidify? (d) What is the composition of this last remaining liquid phase?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 50%Ni-50%Cu alloy is slowly cooled from 1400°C to 1200°C. Determine (1) At what temperature does the first solid phase form andwhat is the solid’s composition?(2) At what temperature does all liquid solidify and what is thelast remaining liquid’s composition?(3) At 1300°C, estimate the compositions of the solid andliquid.(4) At 1300°C, estimate the weight fractions of the solid andliquid.
A 50 wt% Pb–50 wt% Mg alloy is slowly cooled from 700°C to 400°C. (a) At what temperature does the first solid phase form? (b) What is the composition of this solid phase? (c) At what temperature does the liquid solidify? (d) What is the composition of this last remaining liquid phase?
For a 76 wt% Pb–24 wt% Mg alloy, make schematic sketches of the microstructure that would be observed for conditions of very slow cooling at the following temperatures: 575°C, 500°C, 450°C, and 300°C. Label all phases and indicate their approximate compositions.
3 Materials Science. From picture below.Describe in detail the phase transformations (showing cooling curves, corresponding optical backgrounds, etc.) that takes place during solidification of the following alloys:(a) 99% Cu - 1% Al(b) 96% Cu - 4% Al(c) 80% Cu - 20% Al
Please show all work A 65Cu-35Zn brass is heated from 300°C to 1000°C. What phases are present at each 100°C interval?
Cite the phases that are present and the phase compositions for the following alloys: 15 wt% Sn–85 wt% Pb at 100°C
A 80%Sn-20%Pb alloy is melted fully at 300°C and then slowly cooled down to 182°C. Sketch the microstructures at 300°C, 200°C, and 182°C, respectively. Label all phases and indicate their approximate compositions. Also, determine the follows for this alloy at 182°C. (1) The weight fractions of α and β phases.(2) The weight fractions of primary β and eutectic structure.(3) The weight fraction of eutectic β .
I think I am just overthinking this but can someone double-check me and correct me? Suppose the alloy in Example 9.3 in your book is reprocessed to a temperature at which the liquid concentrate is 45 wt% B and the solid-solution composition is 85 wt% B. Calculate the amount of each phase.
For a steel with a 0.2 wt%C, what is the mass fraction and composition of phases at 600 (Please draw connections on the graph)
Briefly describe how precipitation hardening happens in Al alloys (how the microstructure evolves as annealing time increases). Why it first forms q” then q’ before q is finally formed? How does the alloy’s strength change during this process? What are the strengthening mechanisms?
Question: A 50 wt% Ni–50 wt% Cu alloy is slowly cooled from 1400°C (2550°F) to 1200°C (2190°F). (a) At what temperature does the liquid solidify? (b) What is the composition of this last remaining liquid phase?
For a 50-50 Mg-Pb alloy, what would the percent of each phase be at 500°C, 300°C and 100°C?