The link ABC shown in Figure Ql is pin connected at B and rests against a smooth support at A. i. Compute the horizontal and vertical components of reaction at pin B ii. Determine the internal normal force (N), shear force (V) and moment (M) at points D and E 0.3 m 0.5 m 0.4 m 60 0.35 m •C 6 kN.m 2 kN/m 4 kN

The link ABC shown in Figure Ql is pin connected at B and rests against a smooth support at A. i. Compute the horizontal and vertical components of reaction at pin B ii. Determine the internal normal force (N), shear force (V) and moment (M) at points D and E 0.3 m 0.5 m 0.4 m 60 0.35 m •C 6 kN.m 2 kN/m 4 kN

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.4P: Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.

See similar textbooks

Similar questions

A steel plate of dimensions 2.5 x 1.5 x 0.08 m and weighing 23.1 kN is hoisted by steel cables with lengths L1 = 3.2 m and L2 = 3.9 m that are each attached to the plate by a clevis and pin (see figure). The pins through the clevises are 18 mm in diameter and are located 2.0 m apart. The orientation angles are measured to be s = 94.4' and a = 54.9° For these conditions, first determine the cable forces T1 and T2, then find the average shear stress Taver in both pin 1 and pin 2, and then the average bearing stress ?? between the steel plate and each pin. Ignore the weight of the cables.
A beam supported with pin joint at 1 and roller support at 2 carries point loads of F1= 16 kN at A, F2= 25 kN at B, F3= 24 kN at C, and F4= 12 kN at D. Schematic arrangement of the supports and beams with their distances L1 = 323 mm, L2 = 142 mm, L3 = 2015 mm, L4 = 2366 mm and, L5 = 2504 mm are as shown in Figure T1. The students are to position the loads and supports as per the dimensions given and perform the following: (iv). Draw shear force and bending moment diagrams for the given values and identify maximum shear force and maximum bending moment; (v). Identify the support with maximum reaction and provide justification for the answer.
Find the support reacions and joint force of the construction shown on the figure, if; P=12 kN q=9 kN/m M=12 kN and L=2 m
Static problem Determine the forces and internal moment at points 1 and 3 indicated in the figure. Consider the pins at A, B, and C. Points 1 and 2 are located just above and below pin C.
A beam held by a hinge, take 2. The left end of a beam of mass 17.9 kg and length L is fixed to a wall by a hinge. The beam is inclined at 19.8 degrees from the horizontal; it is supported at its right end by a rope forming an angle of 30.3 kg with the horizontal.create a template for:a) the tension in the rope;b) the orientation of the hinge force, relative to the x+ axis.
PROBLEM 3: A right-angled rigid pipe is fixed to a wall at A and is additionally supported through the cable CD as shown in the figure. The tension in the cable is 3 kN. Neglect the weight of the pipe. Use the Right-Hand-Rule to indicate the direction of the moment. [8] Calculate total force reaction at A. (ANSWER: 3.00 KN) [9] Calculate the moment reaction (including correct sign) at A about z-axis. (ANSWER: 2.168 KN-m) [10] Calculate the moment reaction (including correct sign) at A about x-axis. (ANSWER: -0.843 KN-m)
A beam supported with pin joint at 1 and roller support at 2 carries point loads of F1= 16 kN at A, F2= 25 kN at B, F3= 24 kN at C, and F4= 12 kN at D. Schematic arangement of the supports and beams with their distances L1 = 323 mm, L2 = 142 mm, L3 = 2015 mm, L4 = 2366 mm and, L5 =2504 mm are as shown in Figure T1. The students are to position the loads and supports as per the dimensions given and perform the following: (i). Draw the physical diagram of the beam%; (ii). Draw the free body diagram of the beam; (iii). Estimate the reaction forces at the support; (iv). Draw shear force and bending moment diagrams for the given values and identify maximum shear force and maximum bending moment; (v). Identify the support with maximum reaction and provide justification for the answer.
A beam supported with pin joint at 1 and roller support at 2 carries point loads of F1= 16 kN at A, F2= 25 kN at B, F3= 24 kN at C, and F4= 12 kN at D. Schematic arangement of the supports and beams with their distances L1 = 323 mm, L2 = 142 mm, L3 = 2015 mm, L4 = 2366 mm and, L5 =2504 mm are as shown in Figure T1. The students are to position the loads and supports as per the dimensions given and perform the following: (i). Draw the physical diagram of the beam%; (i). Draw the free body diagram of the beam; (iii). Estimate the reaction forces at the support; (iv). Draw shear force and bending moment diagrams for the given values and identify maximum shear force and maximum bending moment; (v). Identify the support with maximum reaction and provide justification for the answer.
I need help please Two gondolas on a ski lift are locked in the position shown in the figure while repairs are being made elsewhere. The distance between support towers is L = 100 ft. The length of each cable segment under gondola weights WB = 450 lb and WC = 650 lb are DAB = 12 ft, DBC = 70 ft, and DCD = 20 ft. The cable sag at B is Î”B = 3.9 ft and that at C(Î”C) is 7.1 ft. The effective cross-sectional area of the cable is Ae = 0.12 in2.(a) Find the tension force in each cable segment; neglect the mass of the cable.(b) Find the average stress (s) in each cable segment.
Four wooden dowels with a diameter of 30mm areattached to a board. Two ropes pass around theanchors and are tensioned by forces P = 110 N and Q =189 N. Calculate the resulting torque applied to the board.
the bent bar AB weighing 10lb/ft is mounted as shown in figure 2 upon a carriage weighing 250 lb. The center of gravity of the carriage is at C midway between the wheels. If P=108lb and there is no frictional resistance at the wheels, find the wheel reaction R1. find the vertical component of the hinge force at A. find the horizontal concept of the hinge force at A.
Please reply as soon as possible, static problem Determine the forces and internal moment at points 1 and 3 indicated in the figure. Consider the pins at A, B, and C. Points 1 and 2 are located just above and below pin C.