Problem 8 A steel bar of thickness h, to be used as a beam, is welded to a vertical support by two fillet welds as shown in the figure. Find the safe bending force F if the allowable shear stress in the welds is rallow. Knowing: b=40mm; c=150mm; d= 60mm; h=5mm; Tallow=130 MPa F

Problem 8 A steel bar of thickness h, to be used as a beam, is welded to a vertical support by two fillet welds as shown in the figure. Find the safe bending force F if the allowable shear stress in the welds is rallow. Knowing: b=40mm; c=150mm; d= 60mm; h=5mm; Tallow=130 MPa F

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.9P: A spherical tank of diameter 48 in. and wall thickness 1.75 in. contains compressed air at a...

See similar textbooks

Similar questions

A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
A pontoon bridge (see figure) is constructed of two longitudinal wood beams, known as bulks, that span between adjacent pontoons and support the transverse floor beams, which arc called chesses. For purposes of design, assume that a uniform floor load of 7.5 kPa acts over the chesses. (This load includes an allowance for the weights of the chesses and balks.) Also, assume that the chesses are 2.5 m long and that the balks are simply supported with a span of 3.0 m. The allowable bending stress in the wood is 15 MPa. If the balks have a square cross section, what is their minimum required width b^l Repeat part (a) if the balk width is 1.5 b and the balk depth is b; compare the cross-sectional areas of the two designs.
Solve the preceding problem using the following data: beam cross section is 100 x 150 mm, length is 3 m, and point load is P = 5 kN at mid-span, Point C is located 25 mm below the top of the beam and 0.5 m to the right of support A.
A bimetallic beam used in a temperature-control switch consists of strips of aluminum and copper bonded together as shown in the figure, which is a cross-sectional view. The width of the beam is LO in,, and each strip has a thickness of 1/16 in. Under the action of a bending moment M = 12 lb-in, acting about the z axis, what are the maximum stresses aaand ecin the aluminum and copper, respectively? (Assume fA, = 10,5 x l0 psi and ecu= 16,8 × 106 psi,)
A spherical tank of diameter 48 in. and wall thickness 1.75 in. contains compressed air at a pressure of 2200 psi. The tank is constructed of two hemispheres joined by a welded seam (see figure). (a) What is the tensile load/ (lb per in. of length of weld) carried by the weld? (b) What is the maximum shear stress rm2Xin the wall of the tank? (c) What is the maximum normal strain e in the wall? (For steel, assume E = 30 X 10 psi and v = 0.29.)
A bridge girder A B on a simple span of length L = 14 m supports a distributed load of maximum intensity q at m id-span and minimum intensity q/2 at supports A and B that includes the weight of the girder (sec figure). The girder is constructed of three plates welded to form the cross section shown. Determine the maximum permissible load q based upon (a) an a I lowable bending stress tra]Um = 110 M Pa and (b) an allowable shear stress r ,. = 50 M Pa.
Two wood beams, each of rectangular cross section (3.0 in. x 4.0 in., actual dimensions), are glued together to form a solid beam with dimensions 6.0 in. x 4.0 in. (sec figure). The beam is simply supported with a span of S ft. What is the maximum moment Mmaxthat may be applied at the left support if the allowable shear stress in the glued joint is 200 psi? (Include the effects of the beams own weight, assuming that the wood weighs 35 lb/ft3.) Repeat part (a) if Mmaxis based on allowable bending stress of 2500 psi.
A hollow steel shaft ACB of outside diameter50 mm and inside diameter 40 mm is held againstrotation at ends A and B (see figure). Horizontalforces P are applied at the ends of a vertical arm thatis welded to the shaft at point C.Determine the allowable value of the forces P ifthe maximum permissible shear stress in the shaft is45 MPa.
a rectangular beam with a span of 20ft is simply supported at both ends. The maximum flexural stress for the beam is 1200 psi and the dimensions of its cross-section are: b=4 in and h=10 in. If the beam is to be loaded at mid-span with a concentrated load of 2000lbs, will the beam collapse?
A brass strip, 50 mm x 12 mm in section, is riveted to a steel strip, Figure (22) 65 mm x 10 mm in section, to form a compound beam of total depth 22 mm, the brass strip being on top and the beam section being symmetrical about the vertical axis. The beam is simply supported on a span of 1.3 m and carries a load of 2 kN at mid-span. (a) Determine the maximum stresses in each of the materials owing to bending. (b) Make a diagram showing the distribution of bending stress over the depth of the beam. Take E for steel = 200 GN/m² and E for brass = 100 GN/m². Ans.( 0) = 130 MN/m²; 0, = 162.9 MN/m²]
A circularbeam, 50 mm in diameter, is welded to support using a fillet weld as in the figure. Determinethe size of the weld, if the permissible shear stress is 100 N/mm2.
The aluminum post shown in the below figure is reinforced with a brass core. Theassembly supports an axial compressive load of P = 9.75 kip and this load is applied tothe rigid cap,. Take Eal = 10 x 103 ksi and Ebr = 15 x 103 ksi. a. Draw the Free Body Diagram (F.B.D), considering a section perpendicular to thelongitudinal axis. Please clearly show that sectional plane along with the upperportion of the body.b. Shall there be any shear and/or moment as an internal loading on the section,which you already have drawn? c. Develop the equilibrium equation.