PROBLEM: Note: 3 stage ideal regenerative cycle An ideal regenerative cycle is executed with steam generation at 9.0 MPa and 550. Before condensation at 0.02 MPa, steam is extracted for feedwater heating first at 2.5 MPa, second at 1.0 MPa, and last at 0.5 MPa. If the mass of the steam generated is 10 kg/s, determine the following: a. Schematic and Ts diagram b. Enthalpies, kJ/kg

PROBLEM: Note: 3 stage ideal regenerative cycle An ideal regenerative cycle is executed with steam generation at 9.0 MPa and 550. Before condensation at 0.02 MPa, steam is extracted for feedwater heating first at 2.5 MPa, second at 1.0 MPa, and last at 0.5 MPa. If the mass of the steam generated is 10 kg/s, determine the following: a. Schematic and Ts diagram b. Enthalpies, kJ/kg

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

IDEAL RANKINE CYCLE: In an ideal Rankine Cycle, steam at 5 MPaa and 500 o C enters the turbine and expands 300 KPaa. For 110,000 kg/hr of steam, find: a) Ideal power output of the Turbine (kW), b) Power to drive the pump (kW), c) Rate of Heat Added (kW), d) thermal efficiency of cycle and engine, e) steam rate of the cycle and engine, f) Heat Rate (PLEASE SHOW COMPLETE SOLUTION AND ENCLOSE ALL THE FINAL ANSWERS ROUNDED OFF TO THE 4TH DECIMAL)
IDEAL RANKINE CYCLE: In an ideal Rankine Cycle, steam at 5 MPaa and 500 o C enters the turbine and expands 300 KPaa. For 110,000 kg/hr of sream, find: a) Ideal power output of the Turbine (kW), b) Power to drive the pump (kW), c) Rate of Heat Added (kW), d) thermal efficiency of cycle and engine, e) steam rate of the cycle and engine, f) Heat Rate (PLEASE SHOW COMPLETE SOLUTION AND ENCLOSED ALL THE FINAL ANSWERS ROUNDED OFF TO THE 4TH DECIMAL)
Consider a simple Rankine cycle and an ideal Rankine cycle with three reheat stages.Both cycles operate between the same pressure limits. The maximum temperature is700°C in the simple cycle and 450°C in the reheat cycle. Which cycle do you think willhave a higher thermal efficiency?
3. A 200 MW power plant operates on a simple Rankine cycle. Steam at 5.2 MPa, 400ºC expandsin a Rankine turbine to 0.036 MPa. Assume actual turbine with isentropic efficiency of 75 % forboth the compressor and expander. 3.1 Heat added in steam Generator , KW 3.2 Power loss at Turbine, KW 3.3 Actual thermal efficiency of the cycle 3.4 Mass of water in kilogram needed for an hour in the condenser if the changeof temperature for the water is 27ºF
1. Consider a steam power plant that operates on a simple ideal Rankine cycle and has a net power output of45 MW. Steam enters the turbine at 7 MPa and 500°C and iscooled in the condenser at a pressure of 10 kPa by runningcooling water from a lake through the tubes of the condenserat a rate of 2000 kg/s. Show the cycle on a T-s diagram withrespect to saturation lines, and determine (a) the thermal efficiency of the cycle, (b) the mass flow rate of the steam, and(c) the temperature rise of the cooling water. Answers:(a) 38.9 percent, (b) 36 kg/s, (c) 8.4°C 2. Consider a 210-MW steam power plant that operateson a simple ideal Rankine cycle. Steam enters the turbine at10 MPa and 500°C and is cooled in the condenser at a pressure of 10 kPa. Show the cycle on a T-s diagram with respectto saturation lines, and determine (a) the quality of the steamat the turbine exit, (b) the thermal efficiency of the cycle,and (c) the mass flow rate of the steam. Answers: (a) 0.793,(b) 40.2 percent, (c) 165…
A binary vapor power cycle consists of two ideal Rankine cycles with steam and Refrigerant 134a as the working fluids. The mass flow rate of steam is 2 kg/s. In the steam cycle, superheated vapor enters the turbine at 8 MPa, 600C, and saturated liquid exits the condenser at 250 kPa. In the interconnecting heat exchanger, energy rejected by heat transfer from the steam cycle is provided to the Refrigerant 134a cycle. The heat exchanger experiences no stray heat transfer with its surroundings. Superheated Refrigerant 134a leaves the heat exchanger at 600 kPa, 30C, which enters the Refrigerant 134a turbine. Saturated liquid leaves the Refrigerant 134a condenser at 100 kPa. Determine (a) The net power developed by the binary cycle, in kW. (b) The rate of heat addition to the binary cycle, in kW. (c) The thermal efficiency of the binary cycle.
Water is the working fluid in a Rankine cycle modified to include one closed feedwater heater and one open feedwater heater. Superheated vapor enters the turbine at 16 MPa, 560 deg C, and the condenser pressure is 8 kPa. The mass flow rate of steam entering the first-stage turbine is 120 kg/s. The closed feedwater heater uses extracted steam at 4 MPa, and the open feedwater heater uses extracted steam at 0.3 MPa. Saturated liquid condensate drains from the closed feedwater heater at 4 MPa and is trapped into the open feedwater heater. The feedwater leaves the closed heater at 16 MPa and a temperature equal to the saturation temperature at 4 MPa. Saturated liquid leaves the open heater at 0.3 MPa. Assume all turbine stages and pumps operate isentropically. Determine (a) the net power developed, in kW. (b) the rate of heat transfer to the steam passing through the steam generator, in kW. (c) the thermal efficiency. (d) the mass flow rate of condenser cooling water, in kg/s, if the…
A binary vapor power cycle consists of two ideal Rankine cycles with steam and Refrigerant 134a as the working fluids. The mass flow rate of steam is 2 kg/s. In the steam cycle, superheated vapor enters the turbine at 8 MPa, 560°C, and saturated liquid exits the condenser at 50 kPa. In the interconnecting heat exchanger, energy rejected by heat transfer from the steam cycle is provided to the Refrigerant 134a cycle. The heat exchanger experiences no stray heat transfer with its surroundings. Superheated Refrigerant 134a leaves the heat exchanger at 600 kPa, 30°C, which enters the Refrigerant 134a turbine. Saturated liquid leaves the Refrigerant 134a condenser at 100 kPa.Determine:(a) the net power developed by the binary cycle, in kW.(b) the rate of heat addition to the binary cycle, in kW.(c) the percent thermal efficiency of the binary cycle.(d) the rate of entropy production in the interconnecting heat exchanger, in kW/K.
A simple rankine ideal cycle with water as the working fluid. Twenty kilograms of steam enters the turbine at 7.356 MPa and 500.356 oC and is cooled in the condenser at a pressure of 10.356 KPa by running cooling water from a lake through the tubes of the condenser at rate of 2000 kg. Show the T-s diagram and schematic of simple rankine cycle. For cycle determin (a) the turbine work, (b) the heat added, (c) the temperature rise of the cooling water, (d) the thermal efficiency of the cycle. For engine, determine (e) the heat added, (f) the thermal efficiency of the engine, and (g) Draw the T-s and schematic diagram.
An engineer has proposed that a simple ideal Rankine cycle that uses refrigerant-134a be used to produce work with heat from a low temperature thermal energy reservoir. The boiler operates at 1.6 MPa, the condenser at 0.4 MPa and the turbine inlet at 80°C. Determinea) the R-134a mass flow rate needed for this cycle to produce 750 kW of powerb) the thermal energy efficiency of the cycle
Consider a power plant that operates on a simple ideal Rankine cycle with refrigerant- 134a (a pure substance) as the working fluid; not water! The refrigerant enters the turbine as a saturated vapour at 1.4 MPa and leaves at 0.7 MPa. The mass flow rate of the refrigerant is 3 kg/s. [Hint: Use Property Tables for R-134a.] (a) Draw this simple ideal Rankine cycle on T-s diagrams. Determine: (b) the thermal efficiency of the cycle and (c) the power output of this plant.
A steam power plant operates on the reheat Rankine cycle. as shown in the schematic diagram (Fig. Q 2). Steam enters the high-pressure turbine at 12.5MPa and 550o C at a rate of 7.7 kg/s and leaves at 2 MPa. Steam is then reheated at constant pressure to 450o C before it expands in the low-pressure turbine. The isentropic efficiencies of the turbine and the pump are 85% and 90%, respectively. Steam leaves the condenser as a saturated liquid. If the moisture content of the steam at the exit of the turbine is not to exceed 5%, then make all the necessary assumptions and determine(a) the condenser pressure,(b) the net power output, and(c) the thermal efficiency.Draw an accurate T-s diagram of the cycle and label all the property values on this diagram.