PROBLEM SP309100 KNhonzontalsupported by a roller at poınt Aand an hinge at point B carnes aconcentrated load (point load)and a uniformly varyıng loadUM) as shown. Determıne thereaction at the supports.beam20 KN/mB6m2m2m

Answered: Image /qna-images/answer/75c81581-909e-4eb2-86f8-e1dc358f59c5.jpg

PROBLEM SP309 100 KN honzontal supported by a roller at point A and an hinge at point B carnes a concentrated load (point kload) and a uniformly varying load UVL) as shown. Determine the reaction at the supports. beam 20 KN/m 6m 2m 2m

PROBLEM SP309 100 KN honzontal supported by a roller at point A and an hinge at point B carnes a concentrated load (point kload) and a uniformly varying load UVL) as shown. Determine the reaction at the supports. beam 20 KN/m 6m 2m 2m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

note: SN = 18, to the topload will be 118kN
Design a purlin for a roof truss having the following data:Span of the truss = 6.0mSpacing of truss = 3m c/c.Inclination of roof = 30oSpacing of Purlin = 2m c/cWind pressure = 1.5 kN/m2Roof coverage= A.C Sheeting weighing 200 N/m2Provide a channel section Purlin.
A light-gage cold-formed steel channel used as purlins are simply supported on the roof truss 4m apart. Sag rods are placed at midspan. Assuming compact section and loads acting on the flange. Use ASD method. The roof continously braces the purlin. Given: Purlin Spacing = 1.5 m Slope = 15 degrees DL = 2.5 kpa LL = 2.5 kpa WL = 1.0 kpa Windward coefficient = 0.25 Properties of channel section: Sx = 185.17x10^3 mm3 Sy = 16.55x10^3 mm3 Zx = 223x10^3 mm3 Zy = 33.4x10^3 mm3 rts = 21 mm ry = 16.79mm Cb = 1.30 Determine allowable flexure strength about the y-axis and x-axis. (kN/m)
-6,00 Design a short square tied column to carry a factored axial design load Pu of 750 kips an a factored design moment Mu of 250 ft.-kips. Place the longitudinal reinforcing uniformly in the four faces. Use f, = 5000 psi and fy = 60,000 psi. o. Then P 350-1.9 h2 1.86 30 ao
the service load bending moments acting on a rectangular beam 333 mm wide and 617mm deep are 139.65kn-m for dead load and 91.15kn-m for live load. f'c=29.99moa fy=414mpa p=0.68pbak db=20mm ds=10mm stirrups are sipral calculate the D/C ratio in percentage
A simply supported rectangular beam of length 6.45m has a width of 390.5mm and an effective depth of610.5mm. The beam is to be reinforced using 12 ?? bars. The beam supports service dead loads ofWd = 13.5kN/m and WL = 35.5kN/m. f'c = 28Mpa and fy=420 MPa Given: b= 390.5 mm d= 610.5mm L= 6.45 m Wd = 13.5 kN/m WL = 35.5 kN/m 1. Calculate the ultimate moment capacity of the beam.2. Calculate the height of the equivalent stress block.3. Determine the number of bars required for this beam.
Draw a shear diagram Cx = 0 Cy=30 Mc = -210 V {0<=x<8} = 0 V { 8< x <=14} = -5 (x-8)
Question:- A 7.5 meters long simply supported structural steel beam carries two concentrated loads P at every third points. Use A 572 Grade 65 steel with Fy=448.18 MPa. The beam is W310x23.8 section having the given properties. A=3040mm² d= 305mm tw= 5.6mm bf=101mm tf= 6.7 mm Ix= 43x10⁶ mm⁴ Iy=1.2x10⁶mm⁴ a) Calculate the allowable bending stress of the compression flange of beam 7.5 fully supported against lateral movement. b) Based from the previous question, calculate the value of concentrated load P that the beam could support safety.
A 2.75-m-diamter wood-stave pipe has 9m3/s of water entering through a horizontal 30oreducing bend where the other end is 1.82 m indiameter. The curved portion is made of steel plate toresist rupture and the bend is embedded in concreteblock weighing 2400 kg/m3. The pressure at entranceof the bend is 138 kPa. The combined weight of thebend and its content is 268 kN. Neglecting friction inthe flow, compute the minimum volume of concreteblock holding the bend that can withstand the thrust ofwater on the bend assuming the coefficient of frictionbetween the concrete and its foundation is 0.30.
A simply-supported T-beam is subjected to two pairs of distributed loads: pair 1 (??1, ??1) and pair 2 (??2, ??2). The geometric, material and loading properties are all given.bf = 1326mmbw = 425mmt = 268mmLbeam = 13.4mWD1 = 54 kN/mWD2 = 152 kN/mWL1 = 53.4 kN/mWL2 = 181.7 kN/mfc' = 22.8 MPafy = 179.9 MPad = 879mmd' = 98mm 1. Solve for the height of the compression stress block using pair 1. 2. Solve for the theoretical steel area using pair 1. 3. Using ?? = 0.004, solve for the theoretical steel area using pair 2. 4. Using ?? = 0.005, solve for the theoretical steel area using pair 2.
Fine the residual forces acting in a truce with members AC = 1000N(T), EG = 520N (T), ans FH = 1200N (C) aa indicated below. Determine the loads P1, P2 and P3
6.D1 A large tower is to be supported by a series of steel wires; it is estimated that the load on each wire will be 13,300 N (3000 Ib). Determine the minimum required wire diameter,assuming a factor of safety of 2 and a yield strength of 860 MPa (125,000 psi) for the steel.