Problems: 1. Determine the forces acting on members BD, CD and CE of the truss loaded as shown using the method of sections. State whether the member is in tension (T) or compression (C). Place your final answers on the tabulation provided. Use the last two digits of your ID number for the value of P in kN (if it is 00, then use 10 kN). Member Force (kN) T/C BD CD Sm CE

Problems: 1. Determine the forces acting on members BD, CD and CE of the truss loaded as shown using the method of sections. State whether the member is in tension (T) or compression (C). Place your final answers on the tabulation provided. Use the last two digits of your ID number for the value of P in kN (if it is 00, then use 10 kN). Member Force (kN) T/C BD CD Sm CE

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.4.3P: Determine the smallest value of yield stress Fy, for which a W-, M-, or S-shape from Part 1 of the...

See similar textbooks

Similar questions

1. An unsymmetrical flexural member consists of a 70 × 600 topflange, a 70 x 400 bottom flange, and a 12 × 180 web.a, Determine the Section Modulus.b. Determine the distance from the top of the shape to the horizontalplastic neutral axis.c. If A572 Grade 50 steel is used, what is the plastic moment MPy forthe horizontal plastic neutral axis?
Given the following allowable stresses:• 50 MPa for shear in rivets• 100 MPa for bearing between a plate and a rivet• 80 MPa for tension in the platesNOTE: Draw FBD(a) If we increase the diameter of each bar to 20 mm, determine the maximum load Pthat can be applied to the lap joint.(b) Using the value computed for maximum load P from (a) compute for the over-allfactor of safety given that the actual P= 20kN.
1. An unsymmetrical flexural member consists of a 70 × 600 top flange, a 70 x 400 bottom flange, and a 12 × 180 web. a, Determine the Section Modulus. b. Determine the distance from the bottom of the shape to the horizontal plastic neutral axis. c. If A572 Grade 50 steel is used, what is the plastic moment MPy for the horizontal plastic neutral axis?
The unknown load P is acting eccentrically with respect to the horizontal and vertical axes of the I-section shown. Knowing that the horizontal eccentricity is a = 1.25 in. and the vertical eccentricity is 2.5 in. determine the largest value of P that can be applied without exceeding either of the following tensile andcompressive allowable stresses:σten = 10 ksiσcomp = 18 ksi
Does the column shown below have enough available strength to support the given working loads? Use ASD. Take E = 29.272 ksi, ry = 2.031 in, K = 1, Fy = 59.03 ksi, Ag = 32.79 in2
A square hollow steel strut if thickness 10mm is pin connected to two connector plates of thickness, 12mm. The connector plates are welded to the base plate of thickness, 12mm. The base plate is fastened to te concrete base by 4-16mm diameter anchor bolts. The diameter of the pin is 16mm. Which of the following most nearly gives the shearing stress in the anchor bolts? Choices 150.00 MPa 59.68 MPa 51.69 MPa 119.37 MPa
Channel sections are used as a purlin. The top chords of the truss are sloped at 5H to 2V. Trusses are spaced 5m on centers and the purlins are spaced 1.4m on centers. Use the properties of the channel section given below. Loads: (Consider all loads pass thru the centroid of the section.) Dead load = 750 Pa Live load = 1,000 Pa Wind load = 1,400Pa Wind coefficients: Windward = 0.3 Leeward = -0.5 Use Fbx=Fby=250 MPa. Determine the maximum value of the interaction equation using the load combination of 0.75(D+L+W)
The prestressed concrete girder is made from plain stone concrete and four 3/4-in. cold-form steel reinforcing rods. Determine the dead weight of the girder per foot of its length. Let B = 13 inches. Unit weight of concrete = 144 lb/ft^3. Unit weight of steel = 492 lb/ft^3. Note: Answer in whole number. Draw and label the FBD properly
Determine the design strength of the beam(properties given below) and the safe service live load if the service dead load is 320 kN.m.Use f'c =22 Mpa and fy=415 MPa. given properties: b=400 mm d'=70 mm d=620 mm As=10-28 mm A's=3-25 mm bars hello please answer this thanks ☺️
A hollow steel [E = 30,000 ksi] tube (1) with an outside diameter of 3.50 in. and a wall thickness of 0.201 in. is fastened to a solid 2.00-in.-diameter aluminum [E = 10,000 ksi] rod. The assembly is attached to unyielding supports at the left and right ends and is loaded as shown. Assume P=19 kips, Q=13 kips, L1=7 ft, L2=9 ft, and L3=9 ft. Determine(a) the stresses in all parts of the axial structure.(b) the deflections of joints B and C.
12. What is the design shear strength (kN) of a 2-leg 12 mmø stirrups spaced at 187 mm on centers in a beam with total depth of 440 mm? Use fy= 415 MPa for main bars and fy= 275 MPa for web reinforcement. Use f'c = 21 MPa if necessary. Use db = 20 mm. Express your answer in 2 decimal places.
The cantilever beam is subjected to the load shown Below. Determine 1. the actual stresses acting at point A. (Hint: Tmas TIN EA). 2. IfG =30 GPa find the angle of twist at the free end of beam. 10 KN