Procedure: 1. Connect the logic circuit required to implement the function F in equation below and write the truth table for the circuit: F(X,Y,Z)= XYZ + XYZ + XYZ + XYZ+ XYZ 2. Connect the logic circuit required to implement the function Z in equation below and write the truth table for the circuit: FI(X,Y,Z)= (X+Y+Z) (X+Y+Z) (X+Y+Z) 3. Derive the Boolean Algebra expression for a gating network that will have outputs "0" only when: (X-1,Y=1,Z=1) (X=0,Y=0,Z=0) (X=1,Y=0,Z=0) the outputs are to be "1" for all other cases? 4. Connect the circuit which derived in step 3 and write the truth table for it ?.

Procedure: 1. Connect the logic circuit required to implement the function F in equation below and write the truth table for the circuit: F(X,Y,Z)= XYZ + XYZ + XYZ + XYZ+ XYZ 2. Connect the logic circuit required to implement the function Z in equation below and write the truth table for the circuit: FI(X,Y,Z)= (X+Y+Z) (X+Y+Z) (X+Y+Z) 3. Derive the Boolean Algebra expression for a gating network that will have outputs "0" only when: (X-1,Y=1,Z=1) (X=0,Y=0,Z=0) (X=1,Y=0,Z=0) the outputs are to be "1" for all other cases? 4. Connect the circuit which derived in step 3 and write the truth table for it ?.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Assume a three-story hospital is built at Expo Center Karachi, and you are hired to design the logic circuit for the newly installed lift. The lift only stops at Ground, Second, Third Floors. The lift has one button (RUN), that can be turned into Up or Down position. When the switch is turned to the UP position (i.e. R=1), the lift goes upward from the Ground floor (i.e. 0) to the top floor (i.e. 3), and if the switch is turned to the DOWN position (i.e. R=0) it will go downward. Design this synchronous sequential circuit for this up-down counter using the JK-flip- flops. Perform all design steps, including state-diagram, state-table, K-map, minimized expressions and finally, the draw the logic circuit.
In a home security system, the main door (O) of home is controlled by a logic operation with the help of RFID card. the Owner, Mrs. Owner, Security Guard and Guest have a designated RFID card - Owner with card W, Mrs. Owner with card X, security guard with card Y and guest with card Z. Whenever, any of the card is NOT inserted, Door remains Closed; when, all the cards are inserted together, the Door is opened. Consider, card NOT inserted as Logic Low (0), card inserted as High Logic (1), door open as Low Logic (0) and door close means High Logic (1).(i) Identify the logic based on the problem statement(ii) Develop the truth table (W, X, Y & Z – inputs, O – output)(iii) Find the Standard SOP and Standard POS expression(iv) Find the Simplified SOP expression using KMAP.(v) Design the system using basic logic gate.
1- Write the output function ? 2- Design a hardware of this circuit? 3- Design the logic circuit on Proteus and Tinkercad? 4- Verify the truth table of Y ?
1. Design a 16 - to - 1 multiplexer using 4- to-1 multiplexer. 2. Using K- Map, simplify the following Boolean expression : Y = Σ (1,3,5,7,9,10,11,13,14,) 3. Build the logic circuit for the following function using Programmable Logic Array (PLA). ?? = ??? + ??? + ??? + ??? ?? = ??? + ??? + ??? + ???
B) A coin-operated cold drink dispenser will provide cold drink (D) under the following conditions: The correct coin (C) is inserted AND A paper cup is in position (P) AND The selector is set t Orange (O) OR Sprite (S) OR Lemonade (L) Write the Boolean expression for the output of the dispenser. Represent the operation of the dispenser in logic circuit 4 get a logic circuit to mimic aorporate checquing system for operatore of a compnny
Draw the equivalent logic diagram of the set-up below
Use Digital Logic Simulator Fill-in the blank boxes with the correct LOGIC GATE/ Full/Half Adder
What is a transmission gate? Draw its circuit circuit diagram. How does it operate? What is the need for a transmission gate? What is it disadvantage?
Draw the equivalent logic circuit diagram of the given expression. F= (ab) + (ac)
Digital Logic Design Show the Diagrams, please as well. Must answer according to the Questions exactly.
Draw the logic circuit for the given expression clearly.
F A,B,C,D) = ∑ (1, 2, 3, 8, 9, 10, 11,14)× d (7, 15) Use Karnaugh map and Quinn McKlausky Method. Draw the logic circuit for the simplified function using NOR gates for both methods. Compare Both methods in terms of cost assuming a Nor gate costs 10 cents.