Pump test system problem:. For the pump test arrangement shown in figure below, determine themechanical efficiency of the pump if the power input is measured to be 3.85 hp when pumping500gal/min of oil (y = 56.0 lb/ft). (1 hp = 33,000 lb-ft/min or 550 lb-ft/s.)%3DHINT:FROM SUPPLIER TABLE FOR Particular Pipe such as Schedule 40,With Certain DN value, OD and Wall thickness are given as below.FlowDNODWallIDFlowThidnessAreaIn)(in)(in)ft2Pump414.5000.237calculatecalculate6-in Schedule 404-in Schedule 406.6250.280calculatecalculate1+Oil(y = 56 lb/ft)20.4 inMercury(sg 13.54)7.

Answered: Image /qna-images/answer/135e76ea-92bb-4b91-baa0-40bb6911667e.jpg

Pump test system problem:. For the pump test arrangement shown in figure below, determine the mechanical efficiency of the pump if the power input is measured to be 3.85 hp when pumping 500gal/min of oil (y = 56.0 lb/ft). (1 hp = 33,000 lb-ft/min or 550 Ib-ft/s.) %3D

Pump test system problem:. For the pump test arrangement shown in figure below, determine the mechanical efficiency of the pump if the power input is measured to be 3.85 hp when pumping 500gal/min of oil (y = 56.0 lb/ft). (1 hp = 33,000 lb-ft/min or 550 Ib-ft/s.) %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Under the action of gravity, water of density ρ passes steadily through a circular funnel into…

A: Consider v as the velocity in the pipe. The head loss due to friction is

Q: A ventilating fan discharges 4.4 m3 of air per second through a duct 91cm in diameter against a…

Q: The mechanism shown in figure is Brake shoe used to investigate the power produced by Pelton wheel…

A: The power obtained at the exit of runner is termed as runner power or turbine power. This is the…

Q: Your second customer wants to determine the required electrical power, which will be used to pump…

A: Consider the steady flow device with control volume as shown. Working substance enter at device 1-1…

Q: A closed vessel contains water up to a height of 2 m and over the water surface there is air having…

Q: A pump is installed to deliver water from a reservoir of surface elevation zero, to another of…

A: The flow rate of water is given by calculating losses by pump and head. Now,

Q: The hydroelectric facility that has been proposed will consist of a turbine with an efficiency of…

Q: b. Analyse the pressure head at point (2) and (3) for the water reticulation system shown in the…

Q: Cross-section 4 A horizontal pipe conveys water between points, which have diameters d1 = 2548 mm…

A: Let Q= Total flow rate in the system v1= Velocity in pipe at cross section 1 =0.922m/s p1=pressure…

Q: A fan delivers 5.1 m^3/sec at a static pressure of 6.167 cm of water when operating at a speed of…

Q: A centrifugal pump used to take water from reservoir to another through 800 m length and 0.15 m i.d.…

A: This problem is related to fluid mechanics. Fluid mechanics is the subject of mechanical engineering…

Q: (1) Q.2.A. Blood flows through the branching blood vessels as shown in figure at a rate of 1o lt…

Q: A 70mm vane axial fan is running at 2000rpm delivers 7.5 cubic meter/sec of air against static…

A: Given DataN1=2000rpmh1=8cmP1=12kWP2=18.1 kWQ1=7.5m3/s

Q: 2. As shown in the figure, two hydraulic cylinders are connected in series and driven by a hydraulic…

A: Given, Piston diameter , D =90 mm Rod diameter , d = 60 mm F1 = F2 = 10 KN Flow through pump , q…

Q: A duct 0.40 m high and 0.80 m wide suspended from the ceiling in a corridor, makes a right angle…

A: Given data as per the question The inner radius = 0.2 m outer radius = 1.0 m The velocity of air in…

Q: Inlet and throat diameters of a horizontal venturimeter are 350 mm and 150mm respectively. The…

Q: :Determine the absolute pressure at the inlet section of the pump. Flow rate of the pump Q=2,3…

Q: A water pipe is laid on a slope of 1 in 40. The pipe is 50 m long. Water flows downwards at the rate…

Q: Problem 24 A fluid is flowing in a 100-mm-diameter pipe with a velocity of 2.50 m/s. The fluid…

Q: 4. Piping system as shown in the figure. Determine the amount of force required to pump 100 L/s of…

Q: Two(2) identical pumps series in connection Suction Pressure = 3.2 Bars Discharge Pressure = 4.95…

Q: For the hydraulic motor in the following figure, geometric volume is 10ml/r, working pressure…

A: Disclaimer: Since you have posted a question with multiple sub-part, we will solve the first three…

Q: Question 1 2 = 40 m P2 = 350 kPa gage a2 = 1.0 1= 30 m P1 = 70 kPa gage a = 1.0 - Pipe D= 0.5 m head…

Q: storage tank through a pipe with cross sectional area 0.05ft². The velocity in the suction line is 3…

Q: Your second customer wants to determine the required electrical power, which will be used to pump…

A: Consider , pump as system.→ mass flow rate of waterm= SAV =S×It4D2×V =103×It4×(0.05)2×1…

Q: A pump draws water from open reservoir A at 20 ft above pump centerline and lifts to an open…

Q: 7) An iron anchor of density 7870 kg/m' appears 350 N lighter in water than in air. The weight of…

Q: 2. A pump 260mm suction pipe and a 150mm discharge pipe is used to deliver 58L/s of water. The…

A: Suction pipe diameter, d1=260 mm=0.26 mDischarge pipe diameter, d2=150 mm=0.15 mWater flow rate,…

Q: A water circulation system is shown schematically in the figure below. Water enters a pump, followed…

Q: Problem 7 For water flow through the control volume shown in Figure 10. Use the Reynolds transport…

A: Given : To find : Momentum flow rates

Q: A fan pressure of 2.54 cm of water t 1.42 m3 per second of air at static pressure of 2.54 cm of…

Q: 33. A pipe has a diameter of 20 cm at section 1 and 6 cm diameter at section 2, as shown. If h = 8…

A: Given that, Diameter of pipe at section 1, d1=20 cm,Diameter of pipe at section 2, d2=6 cm,Pressure…

Q: In Figure 1, a reducing elbow is used to deflect water flow at a rate of 18 kg/s in a horizontal…

A: Find the velocity of water at inlet and outlet also find gage pressure at inlet.

Q: An induced draft fan handles 63,500 cfm in of flue gas with a gas constant of 51.5116 ft-lb / lb-R…

A: Given data, Volume flow rate, Q = 63500 ft3/min Static pressure, Ps = 4 in water Discharge duct…

Q: A reciprocating pump has the following data: Piston diameter.. Stroke.... Suction pipe length..…

Q: ) In cooling tower below, derive the given equations based on the system boundary below (neglect…

Q: Question-1 In the transmission system shown in Figure below, EA = 155 m and ED = 175 m. The…

A: Given Pipe AB L=120m and d=60cm Pipe CD L=850m and d=60cm Pipe BC1 L=200m and d=30cm…

Q: 4. Piping system as shown in the figure. Determine the amount of force required to pump 100 L/s of…

Q: A pump with a suction and discharge pressure of 125kPa and 409 kPa respectively, discharges water at…

Q: = constant d Q16/ A pipe diameter of 400 mm carries water at a velocity of 25 m/s. The pressures at…

Q: In figure raws a on ol a 2. In the system storage tank through a pipe with cross sectional area…

Q: 1. To model power production in a traditional hydroelectricity unit, we can use the below schematic…

A: Given: The density of water, ρ = 998 kg/m^3 The dynamic viscosity, µ = 0.001 kg/ms The tank…

Q: A pumping system has the following characteristics, f=0.015 length of the pipe = (2500 ft) pipe…

A: Friction factor, f=0.015Pipe length, L=2500 ftPipe diameter, d=6 in=612ft=0.5 ftLosses less than…

Q: The rate of flow of water in a pump installation is 60.6 kg/sec. The intake static gage is located…

Q: The mechanism shown in figure is used to investigate the power produced by Pelton wheel turbine.…

Q: 5. Elevation = 100 ft Di = 1 ft (1) e, = 1000 ft %3D D2 = 1 ft lz = 500 ft B Elevation = %3D 20 ft…

Q: For atmospheric pressure above the sliding block of 10 kg mass, find the gauge pressure in the pipe…

A: The simplest form of manometer consists of a U-shaped glass tube containing liquid. It is used to…

Q: A closed tank 5m high contains 2.5 m of water. A nozzle 75 mm in diameter is installed at the side…

Q: water pipe is laid on a slope of 1 in 40. The pipe is 50 m long. Water flows upwards at the rate of…

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

Pump test system problem:. For the pump test arrangement shown in figure below, determine the
mechanical efficiency of the pump if the power input is measured to be 3.85 hp when pumping
500gal/min of oil (y = 56.0 lb/ft). (1 hp = 33,000 lb-ft/min or 550 lb-ft/s.)
%3D
HINT:
FROM SUPPLIER TABLE FOR Particular Pipe such as Schedule 40,
With Certain DN value, OD and Wall thickness are given as below.
Flow
DN
OD
Wall
ID
Flow
Thidness
Area
In)
(in)
(in)
ft2
Pump
41
4.500
0.237
calculate
calculate
6-in Schedule 40
4-in Schedule 40
6.625
0.280
calculate
calculate
1+
Oil
(y = 56 lb/ft)
20.4 in
Mercury
(sg 13.54)
7.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Trending now

This is a popular solution!

Step by step

Solved in 7 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Data: Hp2,3 = 2 m; A3 = 20 cm²; A₂ = 1 cm²; Hp0,1 = 0.8 m; NB= 74%(pump efficiency) To determine: a) the flow (L/s); b) the area of section (1) (cm³); c) the power supplied by the pump to the fluid.
PAY ATTENTION TO THE QUESTION : What is the resulting flow rate in the system if three pumps are used in parallel? (a) 0.483 m^3/s (b) 0.364 m^3/s (c) 0.333 m^3/s (d) 0.563 m^3/s 1. The Head -flowrate curve for a centrifugal pump is given by: HP = 28 -30Q2 Where, HP is in meter and Q is in m3/s . This pump is used to pump water for a system with the following (H-Q) curve: HS = 8 + 150Q2 Where, HS is in meter and Q is in m3/s . IT SAYS : if theee pumps are used in parallel PAY ATTENTION Multiple choice choose correct answer
In a liquor-bottling plant erected at a site 1 km above sea level (Patm=0.898 bar and temperature 8.7°C) where a centrifugal pump discharges 20 l/s of water against a head of 28 m while the cavita on parameter of the pump a=0.5. Where should the pump inlet location be in m with respect to the water surface.
1Two water pumps are arranged in series. The performance data for both pumps follow the parabolic curve fit Havailable =H0 =aV ^2. For pump 1, H0 =5.30 m and coefficient a =0.0438 m/Lpm^2; for pump 2, H0 =8.70 m and coefficient a =0.0347 m/Lpm^2. In either case, the units ofnet pump head H are m, and the units of capacity V are Lpm.Calculate the combined shutoff head. Complete Answer, thank you
A 0.30 m X 0.40 m branch duct leaves a 0.30 m X 0.60 m main duct at an angle of 60°. The air temperature is 20°C. The dimensions of the main duct remain constant following branch. The flow rate upstream is 2.7 m3/s. Find the pressure downstream in the main duct if at 20°C, the mass per unit volume is 1.2041 kg/m3. Group of answer choices 436 Pa 634 Pa 643 Pa 346 Paplease show full soluton for review and analysis
A certain centrifugal pump was tested and its performance curves can be approximated as follows: H = 340 - 1.2(Q2), in feet BP = (0.0521Q3) + (1.25Q2) + (11.042Q) + 134.5, in horsepower where Q is in ft3/s. If two of this pump is connected in series to deliver water to a system whose head requirement is 615 ft, what will be the operating discharge rate in ft3/s of either pumps?
A certain centrifugal pump was tested and its performance curves can be approximated as follows: H = 340 - 1.2(Q2), in feet BP = (0.0521Q3) + (1.25Q2) + (11.042Q) + 134.5, in horsepower where Q is in ft3/s. If two of this pump is connected in series to deliver water to a system whose head requirement is 615 ft, what will be the operating discharge rate in ft3/s of either pumps? Assuming the head is equally divided between the two pumps, what is the efficiency of either pumps (in %)? Take the specific weight of water to be 62.4 lbf/ft3.
The rate of flow of water in a pump installation is 60.6 kg/s. The intake static gage is 1.22 m below the pump centreline and reads 68.95 kPa gage;the discharge static gage is 0.61 m below the pump centre line and reads 344.75 kPa gage. The gages are located close to the pump as much as possible. The area of the intake and discharge pipes are; 0.093 m2 and 0.069 m2 respectively. The pump efficiency is 70%. Take density of water equals 1000 kg/m3. What is the hydraulic power in kW?
A single-stage centrifugal pump having a suction pipe 254 mm in diameter anda discharge pipe diameter of 5 inches is being tested and found out to discharge 48 lps ofwater. A pressure gage connected to the inlet pipe reads 118 mm Hg vacuum and adischarge gage reads 150 kPa at a distance 100 cm above the point where the inletpressure was measured. If the kW rating of the driving motor is 12 kW, calculate a) thepump efficiency. b) if this pump runs at 1800 rpm, what will be the new discharge rate,head, and power developed if the pump speed was increased to 3600 rpm? Assumeconstant efficiency. c) Determine the pump type.
A pump is installed to deliver water from a reservoir of surface elevation zero, to another of elevation 290 ft. The 10 inch-diameter suction pipe (f=0.022) is 90 ft long and the 8-in-diameer discharge pipe (f=0.028) is 4900 ft long. The pump characteristic is defined by hp= 365-20Q2 where hp, the pump head, is in feet and Q is in cubic feet per second. What is the rate at which the pump will deliver the water?
In a test of the centrifugal pump shown in Fig. , thefollowing data are taken: p1= 100 mmHg (vacuum) andp2 = 500 mmHg (gage). The pipe diameters are D1 = 12 cmand D2 = 5 cm. The flow rate is 180 gal/min of light oil(SG = 0.91). Estimate (a) the head developed, in meters,and (b) the input power required at 75 percent efficiency.
The Head -flowrate curve for a centrifugal pump is given by: HP = 28 -30Q2 Where, HP is in meter and Q is in m3/s . This pump is used to pump water for a system with the following (H-Q) curve: HS = 8 + 150Q2 Where, HS is in meter and Q is in m3/s . What is the resulting flow rate in the system if three pumps are used in series? (a) 0.56 m^3/s (b) 0.48 m^3/s (c) 0.33 m^3/s (d) 0.36 m^3/s HINT: what is the resulting Flow-rate in the system if three pumps are used in series ? Choose correct option above