Q-3.Water at 10 °C flows from a large reservoir to a smaller one though a 5-cmdiameter cast iron piping system as shown in the figure below. Determine the elevation z₁ for aflow rate of 6 liters/second.2₁ = ? OSharp-edgedentrance, K₁ = 0.5D = 5 cm9 m-ControlvolumeboundaryStandard elbow,flanged, K₂ = 0.3Gate valve,fully openK₁=0.2-2₂ = 4 m80 mData: The density and dynamic viscosity of water at 10 °C are:p=999.7 kg/m³ and μ = 1.307x10³ kg/m.s. The roughness of cast iron pipe, & = 0.00026 m.-Exit, K₁= 1.06

Given : Dia of cast iron pipe = 5 cm Flow rate = 6 liters/sec To find : Determine the elevation…

Q-3. Water at 10°C flows from a large reservoir to a smaller one though a 5-cm diameter cast iron piping system as shown in the figure below. Determine the elevation z₁ for a flow rate of 6 liters/second. 4₁ = ? Sharp-edged entrance, K₁= 0.5 - Standard elbow, flanged, K₂ = 0.3

Q-3. Water at 10°C flows from a large reservoir to a smaller one though a 5-cm diameter cast iron piping system as shown in the figure below. Determine the elevation z₁ for a flow rate of 6 liters/second. 4₁ = ? Sharp-edged entrance, K₁= 0.5 - Standard elbow, flanged, K₂ = 0.3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: For the retaining wall shown below, determine the total active and passive thrusts on the wall and…

Q: What is the bulk density of wheat at moisture content of 22.2%

Q: The rod has a weight of 5.9 lb/ft. It is supported by a ball-and-socket joint at C and a journal…

A: Given : To Find :

Q: Determine the deflection specified in each of the following beams. Use only one method to solve for…

A: Given: Required: Midspan deflection

Q: Determine the design moment strength of the T-beam. Use fr=20.7 MPa and fy=414 Mpa.

A: Answer we are given f'c = 20.7 Mpa fy = 414 Mpa As = 2-25 mm As = 2 * π4*252 As = 981.75 mm2…

Q: A syphon of diameter 200 mm connects two reservoirs having a difference in elevation of 15 m. The…

A: Given- Diameter of syphon d=200 mm, Difference of elevation of two reservoirs=15 m, Total length of…

Q: A 0.082-m3 sample of soil weighs 1.445kN. When it is dried out in an oven, it weighs 1.301kN. The…

Q: What is the coefficient of thermal expansion and how is it used with regard to concrete masonry?

A: Coefficient of thermal expansion is the unit length change per degree of temperature change. It…

Q: Two wells are drilled 710 m apart in a confined aquifer with a thickness of 42 m. The heads in the…

A: Data given Thickness of aquifer = 42 m Distance between wells, L = 710 m Head of upgradient well=…

Q: For the beam and loading shown, for section n-n (y = 75mm (from base), 1 = 79.688 x 106 mm)…

A: Given data ȳ = 75 mm ( from bottom) I = 79.688 × 106 mm4 Find maximum shear stress and shear…

Q: If you are doing BIM...you should be utilizing all BIM Uses O True O False

A: BIM is utilized for making and overseeing information during the planning, construction, and tasks…

Q: Problem 6.5 - Determine a) the magnitude and location of the resultant mijnímým mj of the…

Q: 4. Axially rigid beam AB has E = 200 GPa and I = 5x105 m², and the truss members BC has E = 200 GPa…

A: Given Data: For axially rigid beam AB:E=200 GPAE=200 ×106KN/m2I=5×10-5m4For truss member BC:E=200…

Q: delivers air at 45°F, 1 atm to a duct system with three branches consisting of two 26-in.-diameter…

Q: 1. The following results were obtained from particle size distribution analysis of three soils - A,…

A: The given data is shown below:

Q: Why can't aesthetic features affect the stability of the bridge?

A: The essential components of a bridge are girders, piers, towers, and just maybe cables. The piers as…

Q: Determine the force in each member of the truss and state if the members are in tension or…

A: Given that : P1 = 30 kN and P2 = 15 kN Determine the force in each member of truss?

Q: Determine the slope and deflection of the elastic curve midway between the supports using a.) Direct…

A: Given: Required: Slope and deflection midway between the support Note:As per bartleby guidelines,…

Q: B 2m 6m 40kN 3m 20kN Determine the force in members EC using Method of Sections.0 3m |F 30kN 3m H

Q: Two couples act on the frame. If d = 4 ft, determine theresultant couple moment. Compute the result…

Q: K K 6 ft PL = 6 k 6 ft 18 ft PL = 6 k * 6 ft ✈ ✈ PL 2 WD = 3 k = 2.0 k/ft

Q: Air within a piston-cylinder assembly, initially at 15 lbf/ in.2, 510°R, and a volume of 6 ft3, is…

Q: A simply supported 14 ft long beam carries a uniform load of 200 lb/ft over it entire length. The…

A: Given : Length of beam = 14ft Uniform load = 200 lb/ft Width of beam = 3.625 in. Depth of beam =…

Q: termine the horizontal and vertical components of reaction at the pins A, B, and C.

Q: A simple horizontal curve of radius 350 ft connects two tangents that form an intersection angle of…

Q: The tension member shown below is a C 310 x 30.8 of A572M gr 345 steel materials. Will it safely…

Q: Draw the shear, bending moment, and axial force diagrams and the qualitative deflected shape for the…

A: As problem is too long, so only 1st part is solved. For 2nd part, post them as a separate question…

Q: மாgaattaanguaangழங்கவழகன - Locate the centroid of the composite crosshatched area. 21 -78 mm

A: Given: Required: Centroid of shaded area

Q: A hydro-electric generating station has a reservoir of capacity 5 million cu. m with a head of 100…

A: Given data, Reservoir capacity = 5 million cu.m Head = 100 m Hydraulic efficiency = 80% Electrical…

Q: Question 19 A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with…

A: Given:- b=230mm d=500mm 4-20mm diameter bars top of 2-16mm bars concrete cover to bar centroid at…

Q: 1.1 For the structure shown in Figure P1-1 F₂2 20 in Member 1 F3 15 in- Member 2 F 10 in Member 3…

A: There are generally two approaches to matrix analysis of structures:- 1. The stiffness Matrix…

Q: 2m 6m 40kN 3m 20kN Determine the force in members EG using Method of Sections.0 3m F 30kN 3m wwwmm H

A: Given data : Determinate truss with pinned and roller support at A and H respectively. Find :…

Q: 1. Determine the support reactions of the parabolic arch shown below and the internal forces at a…

Q: Solve the slope and deflection at points B and C using the Double Integration Method. Point B is at…

A: E = 200 GPa I = 7.5 x 10-6 m4 Beam is symmetrical about C (mid-section) This, the deflection curve…

Q: 4 and max deflection. 8 3KM/ 10.292 3M 112K14/ za $223 23 Mcador 12.21141

A: Given data : Determinate beam with reactions are given Find : Slope at A , deflection at C and…

Q: Determine the force in member DE of the truss shown. State if the members are in tension or…

Q: inflow and outflow resivor initally Vo=500m3 Qin=D200m3 Qout=195m3 e=0.05% Cin=0.01% set up a…

A: Inflow : Water is added to the various components of the hydrologic system through inflow. The…

Q: 3. What FS reading is required to set the top of the wall form to the correct elevation? EL= 99.599…

A: Calculate the FS reading to set the top of the wall form to correct elevation. Here we have…

Q: A trapezoidal channel has a bottom width of 10 ft and side slopes of 2 horizontal to 1 vertical.…

A: Reference : Water resources. Given : Bottom feet b, side slopes z = 2 H and 1 v Slope = 0.0005 and n…

Q: a 4.0 6t C 2.0 b 68 2.0 d

A: A beam is given as shown in the figure above and it has been asked in the question to calculate the…

Q: 1. For the loads given below, calculate the highest load combination. State which load case governs…

A: Given:- The magnitude of the dead load = D = 2.8 kPa The magnitude of the live load = L = 1.9 kPa…

Q: In a railroad layout, the centerlines of two parallel tracks are connected with a reversed curve of…

Q: B D A 700mm Г 1200mm Block A is suspended from two cables. Knowing that the tension in AC is 200 N,…

Q: Survey Question: A total station with a 20"/div. level bubble is one divisions out of level on a…

A: Given: Total station bubble sensitiveness, s = 20''/ div. Altitude angle, θ = 49o 25' 24'' To find:…

Q: 1. Draw the Shear and Moment diagrams and determine the maximum shear and maximum Moment. + 7KN-M 20…

Q: A MC230x35.6 connected to a gusset plate with 24 mm diameter bolts as shown. The steel is A572M…

Q: What is a multipurpose river valley project? Give any four objectives of the multipurpose river…

A: Introduction: Hydrology: Hydrology is the science that includes the presence, distribution, movement…

Q: Determine the minimum coefficient of static friction us which will allow the drum with fixed inner…

A: Given: Required: Value of friction coefficient

Q: Item 7 The members of the truss are assumed to be pin connected. (Figure 1) Figure 1 12 ft of 1 16…

Q: #3A. The rigid bar AB, attached to two vertical ods as shown, is horizontal before the oad P is…

A: The definition of vertical motion is a motion that is normal to some defined horizontal surface. As…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

Q-3.
Water at 10 °C flows from a large reservoir to a smaller one though a 5-cm
diameter cast iron piping system as shown in the figure below. Determine the elevation z₁ for a
flow rate of 6 liters/second.
2₁ = ? O
Sharp-edged
entrance, K₁ = 0.5
D = 5 cm
9 m
-Control
volume
boundary
Standard elbow,
flanged, K₂ = 0.3
Gate valve,
fully open
K₁=0.2-
2₂ = 4 m
80 m
Data: The density and dynamic viscosity of water at 10 °C are:
p=999.7 kg/m³ and μ = 1.307x10³ kg/m.s. The roughness of cast iron pipe, & = 0.00026 m.
-Exit, K₁= 1.06

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Water at 20°C ( ρ= 999.7 kg/m3 and μ=9.7720 x10-4 kg/m · s) is flowing steadily in a hexagonal cross sectional pipe b=1.5cm, 20-m-long at an average velocity of 1.2 m/s. Determine: (a) Hydraulic diameter. (b) The pressure drop. (c) The head loss. (d) The pumping power requirement to overcome this pressure drop.
A cylindrical tank contains water at a height of 55mm, as sbown. Inside is a small open cylindrical tank containing cleaning fluid (s.g.=0.8) at a height h. The pressure Pb=13.4 kPa gage and Pc=13.42 kPa gage. Assume the cleaning fluid is prevented from moving to the top of the tank. Use unit weight of water=9.79 kN/m^3. a) determine the pressure Pa in kPa, b) the value of h in mm, and c) the value of y in mm.
Refer to Fig. P5.4. Water at 10°C flows up AB (5 m long, 40 mm diameter),then along BC (3 m long, 30 mm diameter). The measured pressure at A is 275kPa. (a) Find the pressure at C if the flow rate is 2.0 L/s. Neglect pipe frictionand energy losses. 6) Repeat for the same flow rate in the opposite direction.Table A.1 for water at 10°C: y = 9.804 kN/m².Vertical
A 1.20 m-diameter(internal)horizontal steel penstock conveys water at the rate of3.6 m3/s. The thickness of the pipe wall is 25 mm. Thebulk modulus of elasticity of water is 2.2 GPa. The pipehas length of 1000 m and the friction factor is 0.020. Thewater surface elevation in the reservoir is 60 m. If theflow is stopped completely by closing the valve in 2sec, determine the following:(a) the maximum water hammer pressure that candevelop.(b) the maximum pressure at the valve.(c) the elongation of the pipe in mm (△=ForcexL/AE) foran almost instantaneous closure.
Obtain the gage pressure at the center A of the pipe shown. Neglect surface tension effects. For Liquid 1 specific gravity= 1.5, for liquid 2 specific gravity= 3.2, h1=15cm, h2= 30cm,h3=75cm
Q1: A: What will be the (a) gage pressure (bJabsolute pressure of water, at depth 14m below surface. Use (Pwater 1000 kg/m, PATM 101 kN/m3).
Water is flowing at the rate of 4.7 cu.m./min. through a 150mm-dia. pipe which slopes downwardsuch that a 75mm-dia. exit orifice is 0.60m lower than the upper end. Assume no friction loss. The sharp edged orificehas a coefficient of contraction of 0.65. What is the pressure at the point A in KPa?
(b) A horizontal pipe is diverted upwards with an angle of 25 degrees. Water enters with a velocity of 4.5 ms-1 and exits upwards. The pipe entrance has a diameter of 200 mm and increases two times at the outlet. The inlet gauge pressure reads 80 kPa. If the difference vertical distance between inlet and outlet is 0.4 m, calculate the magnitude and direction of the resultant force on the pipe bend. Neglect energy losses and take the volume of water to be 0.18 m3
An open tank contains 4.93m of oil (sp.g=0.8) and 5.51? of water. Find the pressure (Kpa) at the midpoint level of water
The flowrate of the flow is 0.20 + a/10 m3 /s in a pipe placed on a horizontal plane. The pipe diameters are D1= 0.30 m and D2= 0.20. Please find the force acting to the pipe by the flow. The gauge pressure at (1) is p1 =200 + b*10 kN/m2 . (g=9,81 m/s2, g=10kN/m3 ) a= 4 b=3
Water flows through pipe A whose diameter is 30 cm and into parallel pipes 1, 2 and 3 and out through Pipe B (diameter= 30 cm). The properties of the pipe are as follows: for pipe 1, L= 300 m, diameter = 10 cm f= 0.020; for pipe 2 L= 240 m diameter= 15 cm f= 0.018 and for pipe 3, L= 600 deiameter= 20 cm f= 0.017. The upstram junction has an Elev. 90 m with pressure of 205 kPa; the downstream junction is at Elev. 30 m. If the average velocity in pipe A is 3.0 m/s, find the pressure at downstream junction B. CHOICES: a.496 kPa b.256 kPa c.136 kPa d.376 kPa
A pump draws water from a 20 cm diam suction pipe and discharges through a 15 cm diam pipe in which the velocity is 3.60 m/s. The pressure is – 34. 465 kPa at A in the suction pipe. The 15 cm diam pipe discharges horizontally into air at C inclined at 30 degrees. Find the maximum height and range that the water can reach if B is 1.8 m. above A and 20 hp is delivered to the pump? Assume that the pump operates at 80 % efficiency and that the frictional loss in the pipe between A and C is 3 m.