Q) A two-segment shaft is used to transmit power at constant speed through the pulleys shown above and to the right. Power is input to the shaft at B through a torque of Tg = 230 N-m. A torque of TA = 60 N'm is observed at A, and a torque of Tc= 170 N'm is observed at C. The external torques act in the directions indicated in the figure. Both shaft segments are made of phosphor bronze [G= 42 GPa] and both segments are solid shafts. Segment (1) has a diameter of di = 20 mm and segment (2) has a diameter of dz = 35 mm. a. Determine the torque observed in segments b. Determine the maximum shear stress observed in the shaft c. Determine the angle of twist observed in segments TA TB Tc (1) B L = 300 mm L2 = 915 mm.

Q) A two-segment shaft is used to transmit power at constant speed through the pulleys shown above and to the right. Power is input to the shaft at B through a torque of Tg = 230 N-m. A torque of TA = 60 N'm is observed at A, and a torque of Tc= 170 N'm is observed at C. The external torques act in the directions indicated in the figure. Both shaft segments are made of phosphor bronze [G= 42 GPa] and both segments are solid shafts. Segment (1) has a diameter of di = 20 mm and segment (2) has a diameter of dz = 35 mm. a. Determine the torque observed in segments b. Determine the maximum shear stress observed in the shaft c. Determine the angle of twist observed in segments TA TB Tc (1) B L = 300 mm L2 = 915 mm.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.3.17P: A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and...

See similar textbooks

Similar questions

2-Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller shaft with the following specification. (i) power tranmission = 230 kW(ii) speed = 80 rpm,(iii) Maximum shear stress = 60 MPa(iv) diameter ratio = 1.74(v) The maximum value of the twisting moment is 40% greater than its mean. (i) The mean torque is (Unit is in Nm)=__________ (ii) The maximum torque is (Unit is in Nm)=__________ (iii) The outer diameter of the shaft (unit in mm)=_______________ (iv) The inner diameter of the shaft (unit in mm)=_______________
A shaft is fixed at support C and has a torque of 75lb.ft with respect to free end at a distance of 0.75ft from C. It remains constant for 0.75ft before a negative uniformly distributed torque of 1200lb.ft/ft at a distance of 1.5ft is introduced. The shaft then remains flat for 1.5ft to free end with a torque of 600lb.ft. where in the shaft is the torque equals to negative 1200lb.ft measured from the free end?
What are the maximum, minimum, and average power values for the shaft shown in the figure below if the shaft speed is 50 rpm, l = 14 cm, a = 4 cm, b = 12 cm, P = 750 N, Tmin = -200 N-m, Tmax = 400 N-m.
A steel 0.75-in diameter shaft (G= 12,000 ksi) is subjected to the following torques in lb-ft: TA = 10; TB = 30; TC = 70; TD = 50. The directions of the applied torques are indicated in the figure The bearings shown allow the shaft to turn freely. The length of each segment is equal to 38 in. (a) Plot a torque diagram showing the internal torque in segments (1), (2) and (3) of the shaft. Show the FBD of each segment using a double-headed arrow to represent each torgue. Determine (b) the maximum shear stress magnitude in the shaft. (c) the rotation angle of pulley C with respect to pulley A.
A steel 0.75-in diameter shaft (G= 12,000 ksi) is subjected to the following torques in lb-ft: TA = 50; TB = 70; TC = 30; TD = 10. The directions of the applied torques are indicated in the figure. The bearings shown allow the shaft to turn freely. The length of each segment is equal to 38 in. (a) Plot a torque diagram showing the internal torque in segments (1), (2) and (3) of the shaft. Show the FBD of each segment using a double-headed arrow to represent each torgue. Use the same rule of signs as in the lecture. Determine (b) the maximum shear stress magnitude (ksi) in the shaft. (c) the rotation angle, in degrees, of pulley D with respect to pulley B. Note: Follow the rule of signs with FBD in each sections. Show complete step by step solution and proper FBD. Solid shaft: J = (₶/32 )( D4) Hollow: J = (₶/32)(D4 - d4)
Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller shaft with the following specification. ) power tranmission = 270 kw (1) speed 65 rpm, () Maximum shear stress = 55 MPa (iv) diameter ratio = 1.78 (v) The maximum value of the twisting moment is 40% greater than its mean. Find, (i)The mean torque is (Unit is in Nm)=, (ii)The maximum torque is (Unit is in Nm)=. (iii) The outer diameter of the shaft (unit in mm) (iv) The inner diameter of the shaft (unit in mm)
The circular shaft shown (Figure 2) has dimensions D1 = 24 cm , L1 = 6 m, D2 = 17.5 cm, and L2 = 4 m with applied torques T1 = 100 kN⋅m and T2 = 40 kN⋅m. The shear modulus is G1 = 60 GPa. Point B is halfway between points A and C. a) Draw the torque diagram for the shaft, using the right-hand rule to determine the correct signs. b) For the given shaft, what is the angle of twist at the free end, point D?
A solid shaft in a rolling mill transmits 30kW at 100 rpm. Find the diameter in mm of the shaft so as not to exceed a shearing stress of 80 MPa and an angle of twist of more than 10 degrees in a length of 8 meters. G = 83 GPa
A circular shaft of the dimensions shown in the following figure is subjected to three torques : T1 = 28 k-in, T2 = -8 k-in and T3 = 10 k-in. (a) What is the angle of twist of the right end due to the applied torque? (b) Plot the angle of twist diagram along the shaft. Let, G= 12×106 psi.
A solid constant-diameter circular shaft is subjected to the torques of TA = 560 lb·ft, TB = 1080 lb·ft, TC = 850 lb·ft, and TD = 330 lb·ft, acting in the directions shown. The bearings shown allow the shaft to turn freely.(a) Plot a torque diagram showing the internal torque in segments (1), (2), and (3) of the shaft. Use the sign convention presented in Section 6.6.(b) If the allowable shear stress in the shaft is 4200 psi, what is the minimum acceptable diameter for the shaft?
Engineering Mechanics. A solid circular steel shaft having an outside diameter of 2.00 in. is subjected to a pure torque of T = 8940 lb-in. The shear modulus of the steel is G = 12,000 ksi. Determine the magnitude of the angle of twist in a 6.50-ft length of shaft.
What is the minimum diameter in meter of a solid steel shaft that will not twist through more than 3˚ in 6 meter length, when subjected to a torque of 14 kN m. Use G of 83 Gpa.