Q: For the open loop transfer function ,Draw the root locus after the following additions on the open loop transfer function, then answer the required questions A- Addition a zero at s=-1. What would be the range of for stable closed loop? B- Addition two zeros at s=-1 and s=-4. What would be the range of for stable closed loop and the maximum overshoot? C- Addition two zeros at s=-4 and s=-6. What would be the range of for stable closed loop and the maximum overshoot?

Q: For the open loop transfer function ,Draw the root locus after the following additions on the open loop transfer function, then answer the required questions A- Addition a zero at s=-1. What would be the range of for stable closed loop? B- Addition two zeros at s=-1 and s=-4. What would be the range of for stable closed loop and the maximum overshoot? C- Addition two zeros at s=-4 and s=-6. What would be the range of for stable closed loop and the maximum overshoot?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

b) G(?)=K [(S−1)(S−2) / (S+2)(S+3)] ; Construct nyquist curves for K=1, 5/3, 9 values. Write down the Nyquist stability criterion and explain whether the system is stable or not. c) Define the gain and phase margin, this time on the nyquist curve.
1. Finding the closed loop transfer function of the system2.What is the steady state error of the system when a unit ramp signal is applied to its input?3. Given Km=5 and Kb=0.01, what should be the K value for a steady-state error to occur at the unit ramp input of the system?
sketch the root locus if or the system shown in the figure 2 and answer the following questions the forward transfer function is given by please i need help with 1,2,3,4,5,6
a) Explain the drawing rules and formulas of the Nyquist curve. b) G(?)=K [(S−1)(S−2) / (S+2)(S+3)] ; Construct nyquist curves for K=1, 5/3, 9 values. Write down the Nyquist stability criterion and explain whether the system is stable or not. c) Define the gain and phase margin, this time on the nyquist curve.
The value of the transfer function and constant are unknown, but the system behavior is. The constant was removed from the block diagram, which resulted in the step response curve shown. What should the value of K be so that the steady-state error for a step input is zero?
For the transfer functions given in the control system in the figure, find the relevant E(s) steady state error and approximately draw the response curve for the relevant input. Note: Find the kaher state error ess and the permanent state response yss and show the rise time tr, peak time tp, settling time ts, maximum overshoot M and steady state regions on the curve you drew.
A robotic system with transfer function ?(?) =(100)/(s(0.1s+1)(0.1s +1)) is controlled with gain K as shown in the figure. A)To analyze the frequency response of this system, draw the Nyquist graph. B)Apply the Nyquist stability criterion. C)Verify the stability analysis you made in part (b) by plotting root locus plots for the positive and negative values of the K gain. D)Calculate the gain value that makes this system borderline stable and show it on Nyquist and Root locus graphs. E)Calculate the gain margin, phase margin, gain crossover frequency and phase crossover frequency values. F)Explain whether the system is stable over the gain margin and phase margin values. WE NEED TO SOLVE THE PROBLEM IMMEDIATELY. PLEASE HELP.
Solutions have been given for each part. However, please show the work necessary to reach the transfer function and the equation that satisfies our conditions for settling time.
What is the z-transfer function of the system
Q1: Without using Routh's criterion, determine if the following systems are a asymptotically stable, marginally stable, or unstable. In each case the closed loop transfer function for each system is given؟
Consider a closed loop system with zero order hold.consider Gp(s)=400/s2+400.determine the closed loop transfer function T(z) for the system at T=1sec
A continuous-time system (transfer function) with a frequency layer of 2π / T between its poles. sampling time is not selected in accordance with the Nyquist criteria (overlap should be formed) and zero-pole map, by obtaining the discrete-time transfer function for cases where the open Examine, compare and report the loop and closed loop unit step responses.