Q) In the positive feedback, which of the following statement is true. * (a) It is used in oscillators and the input voltage is decreased (b) The feedback energy is in phase O with the input signal & it is called degenerative Feedback. (c) The gain stability & BW is O decreases while the gain, noise & distortion are increases O (d) All the above

Q) In the positive feedback, which of the following statement is true. * (a) It is used in oscillators and the input voltage is decreased (b) The feedback energy is in phase O with the input signal & it is called degenerative Feedback. (c) The gain stability & BW is O decreases while the gain, noise & distortion are increases O (d) All the above

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.3P

See similar textbooks

Similar questions

The circuit as shown is a shunt-shunt feedback amplifier. Use feedback analysis to find the midband input resistance, output resistance, and transresistance of the amplifier if RI = 500 Ω, RE = 2 kΩ, β0 = 100, VA = 50 V, RL = 5.6 kΩ, and RF = 47 kΩ, when vi and RI are replaced by a Norton equivalent circuit. What is the voltage gain for the circuit as drawn?
The classic feedback ampliﬁer as shown has β =0.125. What are the loop gain T, ideal closedloop gain AIdeal v , actual closed-loop gain Av, and the fractional gain error FGE if (a) A =∞? (b) A =84 dB? (c) A =20?
A. If the forward gain is 5 and feedback gain is 1, determine the close-loop gain of a negative feedback amplifier. answer: B. For a Wien-bridge oscillator (as presented in the lecture), if the feedback resistor has a value of 10-kohm, determine the value of Ri (in kilo-ohm). answer:
The transistor parameters for the circuit shown are VTN = 0.4 V, Kn =0.5 mA/V2, and λ = 0.(a) Discuss the feedback topology, show the input ant output connections (series orshunt)(b) Find the feedback factor β (find the transfer function without feedback first)
Assume for a moment that perfectly accurate resistors were available for feedback networks; that is resistor tolerance is 0%. Then any deviation from the value set by the feedback resistor ratio is caused by insufficient raw op-amp gain. What minimum raw gain would be needed to get within 1% if an intended overall gain of 10? What if the intended gain is 100 instead?
Find the loop gain, ideal transconductance, actual transconductance, input resistance, and output resistance for the feedback ampliﬁer as shown with RI =15 kΩ, RL =10 kΩ, and R1 =3kΩ.
A For a monolithic negative feedback system defined by the open path function, find the gain range (to operate the system at steady state
An op amp has a dc gain of 100 dB and a unity-gain frequency of 10 MHz. (a) What is the bandwidth of the op amp? (b) If the op amp is used to build a noninverting ampliﬁer with a closed loop gain of 60 dB, what is the bandwidth of the feedback ampliﬁer? (c) Write an expression for the transfer function of the op amp. (d) Write an expression for the transfer function of the noninverting ampliﬁer.
Find the desired values below in the feedback amplifier circuit in the figure. a) Find the no-load voltage gain in the amplifier circuit when the Rf resistor is open circuit. b) Voltage and current in amplifier circuit when Rf resistor is open circuit and RL resistor is present Find your earnings. c) When the Rf feedback resistor is connected, the Rf value that makes the feedback current gain Ai/3 find it. Indicate the assumptions you take in your transactions.
Given in the figure is a two-stage amplifier design that employs negative feedback. Answer the following questions. Use the notation (R1 + R2 + ... + Rn) for series resistors and (R1 || R2 || ... || Rn) for parallel resistors for clarity and ease. Assume that the transistors are already biased properly in the saturation region and ro1 = ro2 → ∞. Also assume that the capacitors have infinite capacitance. 1.) Find the expression for the open loop gain Av 2.) Derive the resistance Rin which is the resistance that can be seen at the input port of the amplifier
Is this system internally stable? Now, consider the following feedback diagram: where ? denotes the system above. Is this new overall system internally stable? Comment on the result.
Find the closed-loop transconductance, input resistance, and output resistance for the series-series feedback ampliﬁer as shown if the op amp has an open-loop gain of 80 dB, an input resistance of 25kΩ , and an output resistance of 1kΩ. Assume the ampliﬁer is driven by a signal voltage with a 10-kΩ source resistance, and the feedback network is implemented with R2=91kΩ and R1=10kΩ.