Q. 4 A thick cylinder of 100 mm internal radius and 150 mm external radius is subjected to an internal pressure of 60 MN/m² and an external pressure of 30 MN/m². Determine the hoop and radial stresses at the inside and outside of the cylinder together with the longitudinal stress if the cylinder is assumed to have closed ends.

Q. 4 A thick cylinder of 100 mm internal radius and 150 mm external radius is subjected to an internal pressure of 60 MN/m² and an external pressure of 30 MN/m². Determine the hoop and radial stresses at the inside and outside of the cylinder together with the longitudinal stress if the cylinder is assumed to have closed ends.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cylindrical tank steel pressure vessel 200mm in radius and 4.0m in length, is subjected to an internal pressure of 3.0 MPa. Determine the thickness of tank (nearest mm) if the following stresses are not to be exceeded: tangential stress of 45 MPa and longitudinal stress of 30 MPa. and also show the free body diagram
A thick cylinder internal diameter 240mm external diameter 240mminternal diameter ‘D’ is subject to external pressure of 40MPa. Determine the diameter‘D’ if the minimum hoop stress in the cylinder is not to exceed 200MPa in mm.
Problem No. 1 A standpipe with an inside diameter of 108 in. contains water, which has a weight density of 62.4 lb/ft3. The column of water stands 30 ft above an outlet pipe, which has an outside diameter of 6.625 in. and an inside diameter of 6.065 in. (a) Determine the longitudinal and hoop stresses in the outlet pipe at B. (b) If the maximum hoop stress in the standpipe at point A must be limited to2,500 psi, determine the minimum wall thickness that can be used for the standpipe.
A thick cylinder internal diameter 240mm external diameter240mm internal diameter ‘D’ is subject to external pressure of 50MPa. Determinethe diameter ‘D’ if the minimum hoop stress in the cylinder is not to exceed200MPa.
A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 30 mm. The outer diamter and thickness of the pressure vessel is 500 mm and 10 mm. Its length is 2m. Determine the maximum internal pressure (MPa) that can be applied if the longitudinal stress is limited to 155 MPa, and the circumferencial stress is limited to 55 MPa.
Two brass rods AB and BC, each of uniform diameter, will be brazed together at B to form a nonuniform rod of total length 100 m, which will be suspended from a support at A as shown. The density of brass is 8470 kg/m^3 Determine normal stresses of ((σzz)AB and (σzz)BC) as a function of z, and draw the variation of stresses with respect to z-axis on the same graph.
A composite square member of varying sizes is subjected to axial forces along its centerline, as shown. The members' cross-sectional dimensions, from smaller to larger, are 50 mm ´ 50 mm, 75 mm ´ 75 mm, and 100 mm ´ 100 mm, respectively. (a) What are the normal stresses (in MPa) induced in the bar material at Section A-A, Section B-B, Section C-C? (b) What are the changes in the axial (4.28 ft), width (100mm), and thickness (100 mm) direction (in mm), at Section C-C? Assume n = 0.25 and E = 200,000 MPa., 1 ft = 0.3048 m
A cylindrical steel pressure vessel has an inner radius of 24 inches and wall thickness of 0.25 inches. Determine the tangential and longitudinal stresses when the vessel is pressurized to 125 psi.
A bar of rectangular section shown in is subjected to stresses σx, σy and σz in x, y and z directions respectively. Show that if sum of these stresses is zero, there is no change in volume of the bar.
For a steel rod with a circular cross section with a diameter of D = 20 mm, the following is required: 1. Draw a diagram of the longitudinal force 2. Draw a diagram of normal stresses 3. Determine the total elongation of the rod if Е = 2∙10^5 MPa When calculating, take: а = 2 m, b =1.2 m, F=10 кN - The point of application of force! The work must be done on one sheet of A4 paper, which must show: - Using the method of sections to determine the longitudinal forces in the rod. - Draw a diagram of longitudinal forces N - Determination of normal stresses based on the constructed plot of longitudinal forces. - Draw diagram a normal stresses - Determination of the full extension of the rod
A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E= 15,000 ksi] rods, and a solid steel [E= 30,000 ksi] rod. The bronze rods (1) each have a diameter of 0.625 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.375 in. If all bars are unstressed before the load P is applied, determine the normal stresses in the bronze and steel rods after a load of P= 14 kips is applied.
41.) A cylindrical steel pressure vessel 400 mm in diameter with a wallthickness of 20 mm, is subjected to an internal pressure of 7.875 MPa. Towhat value may the internal pressure be increased if the stress in the steelis limited to 100 MPa?