Q. Calculate the Moment of Inertia of shaded portion about X- axis. 50 mm 50 mm 100 mm 50 mm

Q: For a 3RPS parallel manipulator shown in Fig. 1, draw the graph, and derive the adjacency matrix.…

A:

Q: Task 2 Select a reasonable pressure for the evaporator and condenser in the following scenarios: A)…

A: Soon:- A  evaporator takes heat from refrigerated space which is maintaine at -10 °c , for proper…

Q: P/ IF the Flow vate through the Pum 0.1 mls of water, Find the Punp head.The manometer reading is…

A: The pump head is 14.7157 m.

Q: a) at the position of the image when the boom is horizontal.

A: Given Data The weigth of the boom is:m=25 kg K=500 kg To find: The cylinder force. Now draw the…

Q: 2. A steam-jet pump maintains a temperature 50°C in the evaporator. The cooled water leaves at the…

A: Given Data The temperature maintained by steam jet is:T1=T3=5°C The warm temperature is:T2=10°C The…

Q: e maximum stress and work done at maximum elongation, when 1 load of 75 kN is suddenly applied to…

A:

Q: 3. (a) Calculate the range of mass flow rates of water at 20°C for which the turbine meter of…

A:

Q: Water flows along a horizontal pipe of diameter 75 mm. An orifice plates of diameter 50 mm is…

A:

Q: 2 litre of petrol weighs 14N. Calculate the specific weight, density, specific volume and specific…

A:

Q: The bell crack mechanism shown in Figure is in equilibrium for an applied load of F1 - 15KN at A and…

A: Answer: The magnitude of the resultant reaction force acting at point B is 30.5 kN.

Q: 4 ft A 5 ft→ 7 ft→B At a forward speed of 30 ft/s, the truck brakes were applied, causing the wheels…

A:

Q: Consider a steam power plant operating on the ideal Rankine cycle. Steam enters the turbine at 3 MPa…

A:

Q: Suppose you have a 29 gm. weight of 100% cotton fabric, you need to Print i with reactive dye in two…

A: Reactive dye is a dye that may create a covalent connection with a fibre, producing a persistent…

Q: A torsion test shows that the shear modulus of an aluminum specimen is 4.60 x 10^6 psi. When the…

A: Material elastic properties E is modulus of elasticity G is modulus of rigidity K is Bulk Modulus…

Q: Do the following velocity components represent physically possible flows ? u =x + z? + 5, v = y² +…

A: The feasibility of a fluid flow can be determined using the Continuity Equation, which is…

Q: Radial transverse components: When the rod OA rotates, the pin P moves along the parabola BCD. If…

A:

Q: shows a plane wall of thickness Δx = 21 cm with a thermal conductivity k=0.7 W/(mK).  Given that the…

A:

Q: The hydrometer shown in Fig. P2.87 with no mer- cury has a mass of 0.01 kg. It is designed to float…

A:

Q: Figure Q2 shows a spool with a mass of 20 kg and a radius of gyration ko = 0.16 m. The 15 kg block A…

A:

Q: A pipe 5 m long is inclined at 15° with horizontal. The smaller section of the pipe is in 80 mm…

A: We have a 5 m long pipe that is 15o angled with the horizontal.The smaller piece of the pipe has an…

Q: II. Determine the degrees of freedom for regions U, V, X, Y in the Phase Diagram U X Temperature For…

A: Given : To find : Degrees of freedom

Q: 5. Calculate the magnitude of the horizontal force P, acting as shown, that will cause motion to…

A:

Q: A plate made of mild steel having 10 cm thick, maintaining temperature 250°C. The convection &…

A:

Q: 1. Calculate the forces in all members of the truss shown using the method of joints. 5,000 lb 1,000…

A:

Q: Two horizontal 5.92-kip forces are applied to pin B of the assembly shown. Knowing that a pin of…

A: P = 5.92 kip d = 0.82 inch t = 0.5 inch

Q: A soccer ball is kicked at an angle of 35 degrees and gained an initial velocity of 40 m/s.…

A: Given   Angle = 35o Velocity, U = 40 m/s Find  Maximum height, H  Range, R  Velocity, V

Q: 2.87. The hydrometer shown in Figure P2.87 with no mercury has a mass of 0.01 kg. It is designed to…

A:

Q: Problem. A reversible heat engine operates between high and low temperature reservoirs at TH and TL,…

A: given; In rigid tank;gas moles(n)=4kmolehigh temperature(T1)=500Kpressure(P)=4MPa…

Q: alculate the specific gravity of mater having a mass of 8.35x10-³ kg which displace 0.25 mL when…

A: Given    Mass, m = 8.35x10-3 kg Volume, V = 0.25 mL                  = 0.25 x 10-6 m3 Find…

Q: 6 m 1.0 m 2 m 3 m 2m 2 m The magnitude of one of the forces is T1 = 100 kN. Find the rectangular…

A:

Q: 2. A freezer of 20 TR capacity has evaporator and condenser temperatures of - 30°C and 25°C…

A: Refrigerant is a fluid which is used in a refrigeration cycle for air conditioning systems and in…

Q: Determine the length L of DC so that the center of mass is at the bearing O. Express your answer to…

A: Given:   mass of disk= 2kg d= 0.6m Mass per unit length of  of AB AND DC= 2kg/m   To find: Length L…

Q: For your company you need to mass produce 20-cmx10-cm heat sinks to dissipate heat quickly from an…

A: Given data, Dimension of the base/sink = 0.2 m×0.1 m Convective heat transfer coefficient of the…

Q: A pulley 590 mm in diameter transmits 50 kW at 520 rpm. The arc of contact between the belt and…

A:

Q: Determine the pressure of water at point 'A' In meters of water as shown in Fig. P. 1.13.13. Water…

A:

Q: A rolled l-shaped beam is connected to a steel girder by 4-25mm bolts as shown. Determine the…

A: Long before the flanges begin to yield, the web will entirely yield. As a result, the web yielding…

Q: Determine the distance x to the center of mass of the homogeneous rod bent into the shape shown. If…

A: Equation of the curve is y2= x3. Mass per unit length, m= 1 kg/m

Q: 02(s) for rotational system in Figure 1. T(s) Find the transfer functions G(S) %3D 250 N-m/rad N3 =…

A:

Q: What factors would you consider in selecting materials for US coins?

A: Coins are made of metals that have been chosen for their long-term durability. Coins serve a…

Q: 3. Water is flowing through a 15 cm diameter pipe that consists of a 3 m long vertical and 2 m long…

A:

Q: 6. Determine the moment of inertia of the composite area about the centroidal axis. 240 mm 50 mm 50…

A:

Q: A fan is driven by a belt from a motor which runs at 880 rpm. A medium double ply leather belt 5/16…

A: Calculate the tight side tension in the belt. T1=σallowbt=350 psi10 in×516 in=1093.75 lb

Q: From the given figure below, determine the following: a. Moment under each wheel b. Maximum moment…

A:

Q: The flowrate between tank A and tank B shown in the figure below is to be increased by 15% (i.e,…

A: Release through Pipe when pressure slope is realized number cruncher utilizes Dischargeq=-π8μR4×P…

Q: Density of liquid is 850 kg/m Determine relative density and weight density of the liquid.

A: We know the density of liquid is 850 kg/m3, thus we need to figure out the liquid's relative density…

Q: For Problems 5.16 through 5.29, use the method of sections. 5.16 Determine the forces in members CD,…

A:

Q: In uniaxial loading the poisson's ratio is 0.30 and the strain in the x- direction is 250 x 10^-6 .…

A: Given   Poisson's ratio = 0.30  Strain in the x- direction = 250 x 10-6 Find   Strain in the z-…

Q: The constant vertical force P is applied to the end of the rope that passes over a peg attached to…

A:

Q: Determine the projection of the force F along the pole. F = {2i + 4j + 10OK} kN 2 m - 2 m 1 m

A:

Q: Determine the angle 0 between the edges of the sheet-metal bracket. -400 mm 250 mm 300 mm 50 mm y

A:

Moment of Inertia

Inertia can be termed as a resistance offered by a body to change its state. A rigid body initially at rest will apply resistance when acted by an external force that tends to change its state of rest or velocity, or a body initially at motion will provide resistance in changing its state of velocity or motion for coming to a state of rest. In other words, Newton's first law of motion describes the law of inertia of a rigid body.